wtw KLE 325 Bedienungsanleitung
KLE 325
ba75798e02 01/2009 9
Operating manual
Standard conductivity measuring cell
KLE 325
10 ba75798e02 01/2009
Accuracy when going to
press The use of advanced technology and the high quality standard of our
instruments are the result of continuous development. This may result
in differences between this operating manual and your instrument.
Also, we cannot guarantee that there are absolutely no errors in this
manual. Therefore, we are sure you will understand that we cannot
accept any legal claims resulting from the data, figures or descriptions.
Copyright © Weilheim 2009, WTW GmbH
Reprinting - even as excerpts - is only allowed with the explicit
written authorization of WTW GmbH, Weilheim.
Printed in Germany.
KLE 325 Contents
11
Contents
ba75798e02 01/2009
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.1 Structure and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2 Recommended fields of application . . . . . . . . . . . . . . . . . . . . . 12
2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Overview KLE 325
12 ba75798e02 01/2009
1Overview
1.1 Structure and function
Structure
1.2 Recommended fields of application
zOn site measurements in rivers, lakes and wastewater
zFish farming
zGround water measurements
zApplications in water laboratories
1Measuring electrode
2Temperature sensor in graphite enclosure
3Shaft
4Closing head
5Cable screw joint
35214
KLE 325 Cleaning
13
ba75798e02 01/2009
2 Cleaning
CAUTION
To clean the sensor, disconnect it from the instrument.
Outside cleaning We recommend to clean the sensor thoroughly, especially before measuring
low conductivity values.
After cleaning, thoroughly rinse with deionized water and recalibrate if
necessary.
Aging of the
conductivity
measuring cell
Normally, the conductivity measuring cell does not age. Special measuring
mediums (e.g. strong acids and bases, organic solvents) or temperatures
that are too high may considerably reduce its lifetime or lead to damage. The
warranty does not cover cases where such conditions cause failure or
mechanical damage.
Disposal We recommend to dispose of the measuring cell as electronic waste.
3 What to do if...
Contamination Cleaning procedure
Lime sediments Immerse in acetic acid for 5 minutes (volume
share = 10 %)
Fat/oil Clean with warm water containing washing-
up liquid
Error symptom Cause Remedy
No temperature or
conductivity display
– No connection between
measuring instrument and
conductivity measuring cell
– Cable defective
– Connection between measuring
instrument and conductivity
measuring cell
Measurement delivers
implausible conductivity
values
– Incorrect cell constant adjusted at
the measuring instrument
– Measuring range exceeded
– Contamination in the area of the
electrodes
– Electrodes damaged
– Check / correct the cell constant
– Make sure the correct sensor is
being used for the application
– Clean the conductivity measuring
cell (see section 2).
– Return the sensor
Incorrect temperature
display
– The temperature sensor was not
immersed deep enough in the
measuring solution
– Temperature sensor defective
– Observe the minimum immersion
depth
– Return the conductivity measuring
cell
Technical data KLE 325
14 ba75798e02 01/2009
4 Technical data
General features Measuring principle 2-electrodes measurement
Cell constant 0.84 cm-1 ±1.5 %
Temperature sensor integrated NTC 30 (30 k:at 25 °C / 77 °F)
Dimensions
(in mm)
Weight approx. 135 g
Materials Shaft Epoxy
Connection head POM
Cable screw joint PA
Conductivity electrodes Graphite
Thermistor enclosure Graphite
Connection cable Length 1.5 m
Diameter 6 mm
Smallest allowed
bend radius
fixed installation: 50 mm
flexible use: 80 mm
Plug type Socket, 8 pins
Pressure
resistance Sensor with connection
cable
IP 68 (2 x 105Pa or 2 bar)
Cable plug IP 67 (when plugged in)
The KLE 325 meets the requirements according to article 3(3) of the
directive, 97/23/EC ("pressure equipment directive").
15.3 21.7
120.0
168.0
16.5
KLE 325 Technical data
15
ba75798e02 01/2009
Pin assignment
Measurement
conditions Conductivity measuring
range
10 PS/cm ... 20 mS/cm
Temperature range 0 ... 80 °C (32 ... 176 °F)
Max. allowed overpressure 2 x 105Pa (2 bar)
Minimum depth of
immersion
36 mm
Maximum depth of
immersion
Entire sensor +cable
Operating position Any
Storage
conditions Recommended storing
method
In air
Storage temperature 0 ... 50 °C (32 ... 122 °F)
Characteristic data
on delivery Temperature responding
behavior
t99 (99 % of the final value display after)
<20s
Precision of the temperature
sensor
± 0.2 K
8
6
1
7
NTC
30 kW
NTC
NTC
Shield
not used
Plug from the front: 4
5
7
38
2
6
1
4
2
5
3
Electrode
Electrode
Electrode
Electrode
Technical data KLE 325
16 ba75798e02 01/2009
Wissenschaftlich-Technische Werkstätten GmbH
Dr.-Karl-Slevogt-Straße 1
D-82362 Weilheim
Germany
Tel: +49 (0) 881 183-0
+49 (0) 881 183-100
Fax: +49 (0) 881 183-420
E-Mail: Info@WTW.com
Internet: http://www.WTW.com
Inhaltsverzeichnis
Andere wtw Messgerät Handbücher
wtw
wtw pH 315i Bedienungsanleitung
wtw
wtw LRD 01 Bedienungsanleitung
wtw
wtw LabStation LS Flex/430 Bedienungsanleitung
wtw
wtw VARIO Bedienungsanleitung
wtw
wtw Turb 555 Bedienungsanleitung
wtw
wtw Oxi 3310 Bedienungsanleitung
wtw
wtw inoLab Multi 9620 IDS Bedienungsanleitung
wtw
wtw pH/ION 340i Bedienungsanleitung
wtw
wtw Cond 3110 Bedienungsanleitung
wtw
wtw IQ SENSOR NET Bedienungsanleitung
wtw
wtw Cond 340i Bedienungsanleitung
wtw
wtw Cond 3150i Bedienungsanleitung
wtw
wtw NitraLyt NOA Bedienungsanleitung
wtw
wtw inoLab pH/Oxi Level 1 Bedienungsanleitung
wtw
wtw MULTILINE 1000 Bedienungsanleitung
wtw
wtw Cond 7310 Bedienungsanleitung
wtw
wtw Multi 350i Bedienungsanleitung
wtw
wtw pH 3110 Bedienungsanleitung
wtw
wtw Multi 3410 Bedienungsanleitung
wtw
wtw inoLab Multi 720 Bedienungsanleitung
