Wurth Elektronik 600 600 Installationsanleitung

Read these instructions

completely before

using this tool!

Crimp Tool PN: 600 600

Crimp Head PN:

600 600 601 01

Crimp Head Die Size

.1" / .128" / .151" / .213"

Crimp Tool

Basic Information

Operation Manual – Crimp Tool

02 www.we-online.com

Preface

The Operating Instructions must always be within

reach of the hand crimping tool. This Crimp Sys-

tem Tool may be used only for the intended appli-

cation and in strict compliance with all applicable

safety rules, regulations and practices. It must be

properly maintained, undamaged and in good

working order. Unauthorized modification is pro-

hibited and voids the manufacturer’s warranty.

Always wear safety glasses with side shields and

other appropriate personal protective equipment.

MISUSE MAY CAUSE PERSONAL

INJURY. KEEP OUT OF REACH

OF CHILDREN!

NEVER INSERT FINGERS BETWEEN

THE JAWS OF THE TOOL!

Crimp Steps

Make sure ferrule is well sit in crimp head slot.

Locate ferrule at appropriate hex size according to datasheet.

www.we-online.com

Application

The Crimp System Tool has been developed for

optimal crimping of a large variety of connec-

tors and terminals by using different interchan-

geable crimping dies.

Description

This Crimp System Tool is comprised of the

basic tool with adjustment dial and quick re-

lease, a set of dies, two setscrews for the dies

and positioning locator. The crimping force can

be adjusted (refer to “Adjustment of the Jaw

Spread”).

The ratchet has six steps. It automatically opens

after the sixth step has been passed (principle

of compulsory completion). To prevent dama-

ge to the crimping die or connector, the built-in

quick release (lock) enables the tool to be ope-

ned prematurely in the event of failed crimping.

Release the handle until last click.

Crimp the ferrule manually.

*click*

04 www.we-online.com

For quick release the lock: The lock will open automatically at the end of the crimping process. If

the crimping process is interrupted, the handles of the tool must be pressed together a little and the

lock pushed with an appropriate tool (e.g. scew driver).

Built in quick release (lock)

Press the silver button at lower handle, in order to release the crimp head.

Release completed.

For the moments that is necessary to release to crimp head.

open

*click*

press

www.we-online.com

Insert crimp head manually. Match middle screw hole.

Place. And screw.

1 2

3 4

Crimp Head Assembly

Unscrew. Remove screw.

Slowly remove crimp head manually.

1 2

Crimp Head Replacement

Warranty

These crimp system tool are subject to thorough

quality control before leaving the factory. The en-

closed general terms and conditions of warranty

apply.

Service

Before using the crimp system tool, make sure it

is in a clean and proper operating state. Always

remove crimping residue. Protect the joints from

soiling and apply light machine oil to them re-

gularly. Check the bolts regularly to ensure that

the lock washers and headless screw, securing

the adjustment dial, are intact and tight. All other

maintenance should be performed by the manu-

facturer.

www.we-online.com V1.0/2021

DIENECKARPRINZEN 999900009.0321.500.FLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wurth Elektronik Crimpwerkzeuge Handbücher

Wurth Elektronik

Wurth Elektronik 600 001 Bedienungsanleitung

Wurth Elektronik

Wurth Elektronik 600 620 230 220 Bedienungsanleitung

Wurth Elektronik

Wurth Elektronik 600 648 230 220 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung