XSPC H1 Cube+ Bedienungsanleitung
H1 Cube+
XSpc®
Component list
Contents
Page 3 - 4
Accessories Page 5 - 6
Preparing the base panel Page 7
Preparing the back panel Page 8
Preparing the ront panel Page 9
Attaching the back panel Page 10
Attaching the ront panel Page 11
Fitting the L beams Page 12
Fitting the motherboard tray Page 13
Fitting the side panels Page 14
Radiator placements Page 15
XSpc Page 1
Troubleshooting Page 16
Introduction
XSpc Page 2
The XSPC H1 case is a PC case speci ically designed or high end PC
watercooling. It has support or up to three triple 120mm radiators, two dual
120mm radiators, and leaves plenty o space or tubing routing. The case is
supplied in lat pack orm, so you will need a little time and patience to get it
setup correctly. Assembly should take 1-2 hours, depending on your experience
level.
This manual gives step by step instructions or assembling the H1 case. It is
advisable to read all the way through the instructions at least once be ore you
start assembly. It will save time in the long run.
When you are ready to begin installation, you should irst unpack the box and
check that no components are missing (see pages 3-6). I any parts are missing
rom the box please contact XSPC technical support.
www.xspc.biz/support
Speci ication
Dimensions:
619.3 x 475.6 x 529.8mm
Material:
Brushed aluminium – Black anodized
Screw size:
6-32 UNC
Features:
8x 5.25“ bays *
5x HDD bays (10x with optional extra HDD cage.)
1x SSD tray (up to 10x with optional extra trays)
16x 120mm an grills
- 3x Triple 120mm
- 2x Dual 120mm
- 1x Single 120mm
2x Acrylic windows
*Front 5.25“ bay covers sold separately
[A] Base Panel x1
[D] Top Panel x1
[C] Front Panel x1
[E] Right Panel x1 [F] Left Panel x1
[B] Back Panel x1
Component List
XSpc Page 3
[ ] MB Cover Panel x1 [H] PCI Panel x1
[I] Motherboard Tray x1 [J] HDD Rack x1
[L] L Beam x2[K] 5.25“ Bay Cage x2
XSpc Page 4
SSD Tray x1 Castors x4
PCI Slot Covers x10 Neoprene Pad x1
Power Switch x1 Support Post x1
Accessories
XSpc Page 5
Part 1: Preparing the Base Panel
XSpc Page 7
Take panel [A] and place it on a
flat surface, protected by a clean
sheet.
Place a castor under a corner of
the panel and line up the 4 holes.
Put a screw through each hole.
On the underside of the panel
attach a washer and nut to each
screw and tighten using a
screwdriver.
Repeat the process for each of
the four castors.
Place the HDD cage over the
screw holes shown above.
Use four 6-32 thumb screws to
attach the HDD cage to the panel.
1 2
34
5 6
Part 2: Preparing the Back Panel
XSpc Page 8
Before you continue, make sure
your case matches the photo
above.
Remove the tape from the
neoprene pad and stick it to the
HDD cage. Make sure the holes
line up.
Put panel [B] on a flat surface
facing upward.
Place panel [ ] over panel [B]
and line up the four holes.
Attach panel [ ] using four 6-32
thumb screws.
1 2
3
7 8
Part 3: Preparing the Front Panel
XSpc Page 9
Place panel [C] facing down on a
flat surface.
Take one of the [K] bay cages and
attach it using 6 countersunk
screws.
You will need to use a small
screwdriver due to limited space. Repeat steps 2 and 3 for the other
side.
Flip the panel over and thread the
power cables through the hole on
the front.
On the reverse side place an o-
ring and nut over the switch then
tighten the nut.
12
34
5 6
Inhaltsverzeichnis
Andere XSPC Gehäuse Handbücher
