Xtracycle KickBack 3 Bedienungsanleitung

KickBack 3 Manual

REV3

Our mission:

To empower people with

transformational tools that

move the body and spirit.

www.xtracycle.com

3KB5000

KickBack 3

www.xtracycle.com

Warranty

Xtracycle KickBack 3 Kickstands are guaranteed to be free from manufacturing defects for

one (1) year from the original date of purchase.

Defective products will be repaired or replaced at Xtracycle’s discretion. To determine if a warranty

claim is valid you may be required to return the product to Xtracycle for inspection. Xtracycle is not

responsible for removal, installation or shipping costs. This warranty applies only to the original buyer

and is not transferable.

This warranty does not cover damage from use of this product outside of its intended range or that

resulting from modification or neglect. It also does not cover wear and tear resulting from the normal

use of the product.

Double your warranty to two years!

of purchase to extend your warranty to two years.

http://www.xtracycle.com/register

What’s Included:

A rock steady, dual sided kickstand designed for

strength, safety and easy Xtracycle compatibility.

A: One KickBack 3 (Uncut Legs)

B: Two Xtracycle BridgeBolts

C: Four Nuts and Round Washers

D: One 28mm x 35mm Rectangular Washer

E: Two M5x20mm Bolts

F: Two Plastic End Plugs

G: Two 7/8 Inch Rubber Feet

H: One BoomStrap

Recommended Tools:

10mm Socket Wrench

5mm Allen Wrench

Pipe Cutter or Hacksaw/Cutting Guide

Digital Manual:

http://XCY.CL/kb3install

STEP 1:

If your Xtracycle has a threaded

boss on the underside of the

boom tube (A), just ahead of

the front bridge: start to thread

one m5 bolt into it far enough

to keep the KickBack attached

to the frame. Do not tighten.

Hold the Stand in Place

If it does not: fasten the

included BoomStrap over the

boom tube with two M5 bolts.

Do not tighten.

STEP 2:

Step 2a: With the KickBack legs

folded up, place both Xtracycle

BridgeBolts over the Xtracycle’s

front bridge (B).

Step 2b: The front, left BridgeBolt

leg passes through a rectangular

cutout. Place the rectangular

washer over this leg, then lightly

thread on a washer and nut.

Step 2c: Thread a washer and

nut onto each of the other three

BridgeBolt legs.

Install the Bridge Bolts

STEP 3:

Step 3a: Moving the legs

as necessary, lightly snug all

four nuts with a 10mm socket

wrench. Alternating between

nuts can keep the KickBack

from pulling to one side or the

other.

Tighten Things Down

Step 3b: Put the legs into the

down position and pull them

towards the front of the bike

to ensure that the KickBack

is rotated as far forward as

possible and centered on the

boom tube (A).

Step 3c: Tighten the M5 bolts

on the BoomStrap or the single

M5 bolt below to 3Nm.

Step 3d: Torque all four nuts

to 6 Nm.

Note: You will need to lower the stand

to access two of the BridgeBolt legs.

STEP 4:

Note: If you are fitting the KickBack to an EdgeRunner and want to use the

default kickstand height, you can skip to step 5.

Measure the KickBack 3

Step 4a: With the KickBack

legs in the down position,

measure the distance between

the mounting plate and the

ground (C).

Step 4b: With the KickBack

legs in the up position, place

the rear wheel on something a

half inch above the ground (a

larger wrench works great) and

take the same measurement

(D).

Step 4c: Subtract your measurement (D) from your measurement (C) and write

down the result: __________

STEP 5:

Step 5a: Remove the rubber feet and plastic

end plugs from the KickBack’s legs

Step 5b:

If you are installing on an EdgeRunner: you can

cut the legs 3 inches (76 mm) from the bottom.

This will leave a little over half an inch between

the tire and the ground.

Cut the Legs

STEP 5 Cont’d:

If you’re installing on another Xtracycle or want to fine

tune things, measure up the distance you calculated

in Step 4c from the bottom of each leg and mark that

location to cut.

NOTE: Sometimes the markings on the KickBack legs are

inconsistent, always double check that your cuts are even

with a ruler.

Step 5C: Cut each leg where

appropriate. A pipe-cutter

is the easiest solution, but a

hacksaw and clamp-on guide

will also work.

STEP 6 Finishing Touches:

Replace the end caps and rubber feet. Enjoy your new steady steed!

Andere Xtracycle Fahrradzubehör Handbücher

Xtracycle

Xtracycle SlingSet Bedienungsanleitung

Xtracycle

Xtracycle Longtail CargoBay X3 Series Bedienungsanleitung

Xtracycle

Xtracycle Hooptie Bedienungsanleitung

Xtracycle

Xtracycle FreeLoader Too Bedienungsanleitung

Xtracycle

Xtracycle Everyday BikePack Bedienungsanleitung

Xtracycle

Xtracycle LEAP Bedienungsanleitung

Xtracycle

Xtracycle MagicCarpet Bedienungsanleitung

Xtracycle

Xtracycle P-Rail Bedienungsanleitung

Xtracycle

Xtracycle Freeloader too 2021 Bedienungsanleitung

Xtracycle

Xtracycle RFA Footsies Bedienungsanleitung

Xtracycle

Xtracycle PorterPack Bedienungsanleitung

Xtracycle

Xtracycle PeaPod LT Bedienungsanleitung

Xtracycle

Xtracycle PorterPack Bedienungsanleitung

Xtracycle

Xtracycle RFA Kickback Bedienungsanleitung

Xtracycle

Xtracycle Porterrack Bedienungsanleitung

Xtracycle

Xtracycle RFA Wheelskirt Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung