Xylem YSI Pro20 Bedienungsanleitung

Pro20 / Pro20i

Quick Start Guide

Item #605645

This Pocket Guide is meant to serve as a quick reference in calibrating and operating the

Pro20/Pro20i. It is not intended to replace the information found in the User Manual.

Installing the DO Membrane

1. Prepare the O2probe solution according to the instructions on the bottle. After

mixing, allow the solution to sit for 1 hour. This will help prevent air bubbles

from later developing under the membrane.

2. Remove, and discard the red protective cap or used membrane from the sensor.

3. Thoroughly rinse the sensor tip with distilled or deionized water.

4. Fill a new membrane cap with probe solution. Avoid touching the membrane

portion of the cap.

5. Thread the membrane cap onto the sensor, moderately tight. A small amount of

electrolyte will overﬂow.

6. Screw the probe sensor guard on moderately tight.

Setting Sensor & Membrane Type

The instrument will step you through an initial conﬁguration when powered on for the

ﬁrst time. This allows you to set the language, sensor, and membrane options. Use the

up or down arrow keys to highlight the appropriate language, sensor, and membrane,

then press enter to conﬁrm. To change the sensor or membrane type after the initial

conﬁguration, press the Menu key.

The instrument’s Sensor Type must be conﬁgured for the sensor installed.

Failure to do this may result in damage not covered under warranty.

Barometer Calibration

The barometer reading must be accurate to ensure accurate DO% calibrations and DO

readings.

If your barometer requires an adjustment:

1. Determine your local barometric pressure (BP) in mmHg from a mercury

barometer, an independent laboratory, or from a local weather service. If the

BP reading has been corrected to sea level, use the following equation to

determine the true BP in mmHg for your altitude.

True BP = (Corrected BP in mmHg) – {2.5 * (Local Altitude in feet/100)}

DO Calibration

The Pro20/Pro20i can be calibrated in % saturation, mg/L, or ppm. Calibration of any

option (%, mg/L, or ppm) will automatically calibrate the others. The Pro20/Pro20i can

be calibrated with the press of one key when One Touch Cal is enabled in the System

Setup menu.

The following procedure outlines the % saturation calibration option with and without

One Touch Cal enabled.

1. Moisten the sponge in the cal/transport sleeve with a small amount of water

and install it on the probe. The cal/transport sleeve ensures venting to the

atmosphere. Make sure the DO and temperature sensors are not immersed

in the water.

2. Turn the instrument on. If using a polarographic sensor, wait 10 minutes for the

DO sensor to stabilize. Galvanic sensors do not require a warm up time.

3. Ensure the barometer reading and salinity correction values along the bottom of

the screen are accurate.

4. Press and hold the Cal key for three seconds.

5. If One Touch Cal is enabled, the instrument will indicate Calibrating %DO on

the display and automatically calibrate the sensor to the barometer reading and

salinity correction value.

6. If One Touch Cal is not enabled, highlight %or %Local and press Enter. The

Pro20/Pro20i will display the current DO% and temperature readings along

with the % calibration value. Wait at least 3 seconds, then, once the DO% and

temperature readings are stable, press Enter to complete the calibration.

7. Calibration Successful will display for a few seconds to indicate a successful

calibration and then the instrument will return to the run screen.

8. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the error message and return to the run screen.

Salinity Compensation Calibration

The Pro20/Pro20i uses an inputted salinity value in ppt (parts per thousand) to

compensate dissolved oxygen mg/L values.

2. From the run screen, use the up or down arrow keys to highlight the barometer

box then press enter.

3. Use the up or down arrow keys to adjust the barometer reading to the local,

true barometric pressure.

4. Press enter to conﬁrm and save the barometer adjustment.

To adjust the salinity compensation value:.

1. Use the up or down arrow keys to highlight the salinity box on the run screen,

then press enter.

2. Use the up or down arrow keys to adjust the salinity compensation value to the

salinity of the water you are testing.

3. Press enter to conﬁrm and to save the new salinity compensation value.

Taking Measurements

The Pro20/Pro20i can be calibrated in %saturation, mg/L, or ppm. Calibration of any

option (%, mg/L, or ppm) will automatically calibrate the others. The Pro20/Pro20i can

be calibrated with the press of one key when One Touch Cal is enabled in the System

Setup menu.

The following procedure outlines the % saturation calibration option with and without

One Touch Cal enabled.

1. Turn the instrument on and wait 5-15 minutes if using a polarographic sensor.

2. To take readings, insert the probe into the sample. Move the probe in the

sample at a rate of at least 6 inches per second until the readings stabilize.

3. Highlight Save and press Enter to store the reading. The instrument will

conﬁrm that the reading was successfully saved.

Visit YSI.com/Pro20 or YSI.com/Pro20i to

ﬁnd the User Manual, specs, and accessories.

Item# 605645 Dwg# 605645

January 2020 Rev E

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Contact Information

This page is intentionally left blank.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xylem Messgerät Handbücher

Xylem

Xylem ebro SSX 210 Bedienungsanleitung

Xylem

Xylem wtw pHotoFlex pH Bedienungsanleitung

Xylem

Xylem Sensus 412 Series Bedienungsanleitung

Xylem

Xylem ebro EBI DA Set Bedienungsanleitung

Xylem

Xylem WTW SenTix ORP-T 900-P Bedienungsanleitung

Xylem

Xylem YSI Pro1020 Bedienungsanleitung

Xylem

Xylem SI Analytics Lab 865 Bedienungsanleitung

Xylem

Xylem YSI ProQuatro Professional Series Bedienungsanleitung

Xylem

Xylem FLYGT CCD 301 Bedienungsanleitung

Xylem

Xylem WTW Oxi 3310 Bedienungsanleitung

Xylem

Xylem WTW pHotoFlex pH Bedienungsanleitung

Xylem

Xylem wtw Multi 3310 IDS Bedienungsanleitung

Xylem

Xylem SonTek RiverSurveyor Bedienungsanleitung

Xylem

Xylem Bellingham+Stanley OPTi Bedienungsanleitung

Xylem

Xylem SENSUS PolluFlow Bedienungsanleitung

Xylem

Xylem YSI Pro2030 Bedienungsanleitung

Xylem

Xylem SENSUS PolluTherm Integrator Bedienungsanleitung

Xylem

Xylem SI Analytics HandyLab 200 Bedienungsanleitung

Xylem

Xylem WTW TetraCon 925 Bedienungsanleitung

Xylem

Xylem WTW Turb PLUS 2000 Bedienungsanleitung

Xylem

Xylem wtw Cond 7110 Bedienungsanleitung

Xylem

Xylem wtw pH/ION 7320P Bedienungsanleitung

Xylem

Xylem Sontek River Surveyor RS5 Bedienungsanleitung

Xylem

Xylem WTW pH/ION 3310 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung