Xylem Laing Thermotech E-10 Series Bedienungsanleitung

ITT Laing E-10 circulation pumps E10-NCHN2W-19, E10-NCHN2W-26, E10-NCTN2W-19, E10-

NCTN2W-26, E10-NSHN2W-20

ITT Laing E-14 circulation pumps E14-NSTNNN2W

ITT Laing E-10 & E-14 Circulation Pump Installation, Operation and Warranty Manual

(To be read / used in conjunction with E series pump manual)

Unpacking when unpacking the unit, inspect carefully for any damage that may have occurred in transit.

Check for loose, damaged or missing parts. Any problem - contact the supplier purchased through immediately. Do

not attempt to repair or modify in any way or warranty may be void.

Installation

These pumps have been evaluated and authorized for water use only in spa / pool applications. Ensure the power

source is correct depending on which voltage pump you purchased and 60Hz. Ensure installation is in a clean, dry,

weather & humidity protected location with adequate air ventilation. Ambient temperature not to exceed 110

degrees F. Ensure the power cord is run in such a way that any water that may get on it, cannot run down the cord

to the motor. This unit cannot be submerged - ensure it cannot flood. Protect cords from sharp objects, hot

surfaces; avoid kinking or coiling of the cord. Replace damaged cords immediately. Locate pump as close as

possible to the fluid source thus making the suction line as short and direct as possible, using tubing on the suction

that cannot collapse, such as a reinforced type. Support the tubing independently of the pump. Use clamps to

secure and seal the tube to the pump. Laing pumps are liquid lubricated. How they are mounted and water

condition are important. Thoroughly clean and flush the system before installing the pump Plumbing valves,

fittings, etc. should be positioned to avoid leakage onto the pump. Ensure plumbing is designed and installed in

such a way that the pump will fill with water when the plumbing system fills, to avoid air locking and dry running.

Mounting

For installation purposes, the arrows on the side of the pump housing indicate the direction of water flow through

the pump. Ensure the pump and piping is adequately supported. Do not mount the motor above the wet end.

Correct orientation of the pump includes mounting horizontally or vertically with suction facing upward only. The

pump can roll on its foot to allow different angles of discharge alignment. Do not position with discharge port

lower than inlet / suction port. This helps prevent air locking.

Operation

Completely fill the plumbing system before operating the pump. Do not start the pump until the plumbing system

has been filled. Make sure isolation valves are fully open and the pump is flooded with water. Purge air from the

plumbing system prior to operating the pump. This can be achieved by loosening the plumbing connection at the

pump to allow any air present, to escape. These 2 steps are very important. The pump can never be allowed to run

dry as this can severely damage the pump and will void warranty. Operate the pump. Ensure water is pumping

through the plumbing system. Turn off immediately if no water is flowing within 30 seconds. Once running

correctly, recheck after 5 minutes to ensure continued proper operation. It may be necessary to open a discharge

valve, port or fixture to ensure all air is purged. The pump should be running quietly. If gurgling is heard, it may

mean that air is still in the system. Turning the pump on and off several times will generally clear remaining air. If

gurgling noises persist, recheck and purge the system (note that ozone injection can make a gurgling sound at the

injector and not be a pump issue). Dry run protection. Pump motors are fitted with dry run protection to preserve

the MOTOR. If a dry run condition occurs, the motor will stop and restart numerous times in the attempt to purge

air. If this condition remains, the motor will turn off and remain off until the power is interrupted. This does not

guarantee protection of the wetend / rotor bearing as dry running can cause failure NOT covered by warranty. This

dry run motor protection prevents motor failure. A failed rotor due to dry running or chemical / water condition

damage, can be ordered from Australian Spa Parts and replaced rather than a complete pump.

Trouble Shooting

Motor will not start or run: Improper electrical connection, blown fuse or circuit breaker, loose or broken wiring,

foreign object stuck in impeller, motor failure, dry run motor protection has operated. Pump will not prime: leak,

kink or obstruction in suction line, pump is worn, dirty / blocked filter Little or no discharge: Air in pump, suction

blockage, head to high, blockage in pump, pump not running, dirty / blocked filter Noisy operation: Air in pump

housing / dry running, worn rotor bearing, debris in pump.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xylem Wasserpumpe Handbücher

Xylem

Xylem GOULDS LB Bedienungsanleitung

Xylem

Xylem RM1100B Bedienungsanleitung

Xylem

Xylem Lowara MPB Handbuch

Xylem

Xylem e-AB3 Bedienungsanleitung

Xylem

Xylem Bell & Gossett 60 Series Bedienungsanleitung

Xylem

Xylem Jabsco 15170 Series Bedienungsanleitung

Xylem

Xylem Lowara Micro PRESFIX Bedienungsanleitung

Xylem

Xylem rule Tournament 401C Handbuch

Xylem

Xylem GOULDS 2GFK2412H Bedienungsanleitung

Xylem

Xylem LOWARA e-LNE Series Bedienungsanleitung

Xylem

Xylem LOWARA Sekamatik 12MK7 Bedienungsanleitung

Xylem

Xylem Bell & Gossett e3-4 Series Bedienungsanleitung

Xylem

Xylem Lowara Ecocirc Premium Series Bedienungsanleitung

Xylem

Xylem GOULDS 45HB-70HB Betriebsanleitung

Xylem

Xylem FLYFT P7900 Bedienungsanleitung

Xylem

Xylem Bell & Gossett P86108D Bedienungsanleitung

Xylem

Xylem McDonnell & Miller MM-706B Bedienungsanleitung

Xylem

Xylem FLOJET Industrial 2100 Bedienungsanleitung

Xylem

Xylem Bell & Gossett e-82SC Bedienungsanleitung

Xylem

Xylem LOWARA e-LNEEE Fehlerbehebungshandbuch

Xylem

Xylem e-1532 Series Bedienungsanleitung

Xylem

Xylem Rule Mate RM500A Bedienungsanleitung

Xylem

Xylem Bell & Gossett WEHT0311M Handbuch

Xylem

Xylem Rule Mate Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung