Xylem Rule LoPro 2004210 Bedienungsanleitung

Fully Automatic Bilge Pump

INSTRUCTION MANUAL

Purpose of this manual

The purpose of this manual is to provide necessary information for product installation,

operation and maintenance.

CAUTION: Read this manual carefully before installing,using or servicing this product.

Failure to follow the instructions within this manual could result in explosion, property

damage, severe personal injury and/or death.

General safety rules. These are safety rules that apply:

• Always keep work area clean

• Pay attention to the risks presented by gas and vapors in the work area.

•Avoid all electrical dangers. Pay attention to the risks of electric shock or arc ash

hazards

• Always bear in mind the risk of drowning, electrical accidents and burn injuries

User safety

DANGER: This product is not intended for damage control or to deal with ooding

resulting from hull damage. This product is intended to be used in Bilge Pumping

Systems for small craft with a hull length up to 24 meters, as described within the intro-

duction and scope of ISO 15083. Bilge Pumping Systems, as specied in ISO 15083,

are limited to normal amounts of water in an intact boat due to spray, rain, seepage,

spillage, and occasional small amounts of water shipped from boat movements in

heavy weather. Use of product in any other way could result in ooding, catastrophic

damage to craft, serious personal injury, or death.

WARNING: This pump is designed for use with fresh water and salt water ONLY. Use

with any other hazardous, caustic, or corrosive material could result in damage to the

pump and the surrounding environment, possible exposure to hazardous substances

and injury.

The following is a summary of typical wiring installations:

Disconnect power before installing or servicing the pump.

Our pump is equipped with silicone blocked, tin coated 16 gauge wire. Please follow the table below when extending

the wires.

This pump must be fused with a 7.5 amp fuse (not included).

All potential sources of ignition located in spaces containing gasoline powered machinery or gasoline fuel tank(s), or joint

tting(s), or other connection(s), between components of a gasoline system, shall be ignition protected in accordance with

the requirements of ABYC E-11,AC and DC Electrical Systems On Boats.

The electrical wiring, connections,and installation shall be in accordance with the requirements of ABYC E-11, AC and DC

Electrical Systems On Boats.

Electrical

Brown wire

Brown/white wire

Black wire

Automatic

Manual override

Ground

7.5 Amp

Fuse

ON-OFF -Auto

Switch

Brown-Automatic

Hold nger over black

dot for ve seconds to

test pump

Three position

switch

Brown/white-Manual

Black-Ground

Wire Size Table

Total Wire Length (positive to pump) - feet (meters)

0-15 ft 15 - 20 ft 20 - 30 ft 30 - 60 ft 60 - 90 ft

0-4.5 m (4.5 - 6 m) (6 - 9 m) (9 - 18 m) (18 - 27 m)

16 AWG 14 AWG 12 AWG 10 AWG 8 AWG

(1.5 mm2) (2.5 mm2) (4 mm2) (6 mm2) (10 mm2)

Bilge pumps shall be mounted in accordance with the pump manufacturer instructions, and in an accessible location to

permit servicing and cleaning of the intake and/or screening.

On boats with an enclosed accommodation compartment, an audible alarm shall be installed indicting that the bilge water

is approaching the maximum bilge water level.

Bulkhead penetrations shall be in accordance with the requirements of ABYC H-2, Ventilation of Boats Using Gasoline, to

minimize the potential for migration of carbon monoxide from machinery compartments containing gasoline engines to

adjacent accommodation compartments.

Potential electrical sources of ignition located in spaces containing gasoline powered machinery, or gasoline fuel tank(s),

or joint tting(s), or other connection(s) between components of a gasoline system, shall be ignition protected, unless the

component is isolated from a gasoline fuel source as described in ABYC E-11.5.3.3

Exception:

1. Boats using diesel fuel as the only fuel source.

2. Outboard engines mounted externally or in compartments open to the atmosphere in accordance with the

requirements of ABYC H-2,Ventilation of Boats Using Gasoline.

The bilge pump inlet shall be located so that excess bilge water can be removed from the bilge at static oating position,

and at maximum conditions created by the boat’s motion,heel, and trim.

Pumps with automatic controls shall be provided with a visual indication that power is being supplied to the pump.

7.5 Amp

Fuse

7.5 Amp

Fuse

ON-OFF

Switch

Seal closed

Brown-Automatic

Two position

switch

No switch

Brown/white-Manual

Black-Ground

Pump will cycle every 2.5 minutes to sense for water.

Water will reach approx 1.3” (3.3 cm).Good for

shallow bilges and small compartments.

To change from Low to High sensor setting,

unlock the motor cartridge by turning

counter-clockwise.Turn the cartridge 180º

until the “H” is on top and reinsert the motor

cartridge.Turn the motor clockwise to lock.

Water will reach approx 2” (5 cm).Good for shower

boxes,very wet areas, narrow bilges.

Best practice: Periodically clean the sensor housing with a mild detergent to remove any build-up that may interfere with

the proper operation of the bilge pump. If the sensor accumulates excessive build-up,the pump will enter the timer mode

to protect the pump and the vessels batteries.Once the debris is removed, the pump will return to level sense mode.

Installation:

We recommend using #8 Stainless Steel screws of an adequate length as to secure the pump but not penetrate the entire

thickness of the hull. Use a exible sealant in the screw holes to prevent water from penetrating the screw holes.

Screws

Disassembly and reassembly

Best practice: Use two stainless steel

hose clamps to attach hose to

hose barb.

During the winterization of a vessel, it’s recommended that you remove the check valve (if equipped) and drain any residual

water from the plumbing.

Please note that the check valve should NOT be used

with the elbow tting. The check valve and elbow

combination greatly restrict the ow.

Plumbing:

This bilge pump has been designed to be used with exible hose. Rigid piping or tubing may damage the pump or the pump’s

discharge.

Factors that reduce the ow of a bilge pump may include but are not limited to the following:

•The length of discharge piping (longer runs reduce ow)

• The number or radius of bends

•The roughness of the interior surfaces of piping and ttings (smooth bore hose is best)

•The reduction (hose restriction) in cross-sectional area of discharge system components such as check valves and

thru-hulls

Attach the discharge hose to the hose barb using stainless steel hose clamps.

The thru-hull discharge tting should be mounted at least 8” (20.3 cm) above the heeled water line to prevent water

siphoning in from outside the vessel or the discharge may be located below the maximum heeled waterline if the

discharge line is provided with both of the following:

•A seacock installed in accordance with the requirements of ABYC H-27, Seacocks, Thru-Hull Connections, and

Drain Plugs, and

•A vented loop or other means to prevent siphoning into the boat.A check valve shall not be used for this purpose.

If the discharges of several pumps are manifolded to discharge through a single thru-hull tting, the system shall be

designed so that the operation of one pump will not back feed another pump, and the simultaneous operation of each

pump will not diminish the pumping capacity of the system. A check valve shall not be used in the discharge manifold

system.

A check valve may be used only when necessary to prevent an automatic bilge pump from cycling on and off due to back

ow from the discharge line.

Hose connections shall be secured with a non-corrosive type of clamp, or be mechanically fastened with permanently-

attached end ttings, such as swaged sleeve. Threaded inserts shall be attached with corrosion resistant metallic clamps.

8.9"/22.6cm

2.4"/6.1cm

5.9"/15.0cm

3"/7.6cm

Mounting Holes

1.8"/4.5cm

Mounting Holes

2.35"/5.9cm

3"/7.6cm

2.4"/6.1cm

4.86"/12.3cm

0 100 200 300 400 500 600 700 800 900

Head (Ft H20)

Flow (GPH)

Performance at 12.0 Volts 1-1/8" Adapter

1" Adapter

3/4" Adapter

Dimensional Drawing

Flow Curves

SEALANT

We hereby declare, under our sole responsibility, that our product to which this declaration

relates has been designed to comply in accordance with the following Directives:

Electromagnetic Compatibility Directive 2004/108/EC

Recreational Craft Directive 2003/44/EC

RoHS 2011/65/EU. Regulation No. 1907/2006

With the relevant selections of the following Standards:

ISO 8846:1990 / Ignition Protection

ISO 8849:2003 / Electrically Operated DC Bilge Pumps

ISO 10133:2012 / Extra Low Voltage D.C.Installations

ISO 15083:2003 / Bilge Pumping Systems

This product is intended to be used in Bilge Pumping Systems for small craft with a hull

length up to 24 meters, as described within the introduction and scope of ISO 15083. Install

following the Provisions of the Recreation Craft Directives 2003/44/EC.

All mounting holes must be sealed with a marine

grade sealant to prevent water intrusion.

Install to ABYC

H-22 and E-11

&KHFNRXWWKHFROOHFWLRQRIERDWSOXPELQJZHRIIHU

Inhaltsverzeichnis

Andere Xylem Wasserpumpe Handbücher

Xylem

Xylem G&L A-C 8100 Series Bedienungsanleitung

Xylem

Xylem Bell & Gossett e-82SC Bedienungsanleitung

Xylem

Xylem FLYGT Concertor Bedienungsanleitung

Xylem

Xylem Bell & Gossett 1510 Series Bedienungsanleitung

Xylem

Xylem Bell & Gossett e-80SC Series Bedienungsanleitung

Xylem

Xylem FloJet 3426 Series Bedienungsanleitung

Xylem

Xylem Goulds NPE Handbuch

Xylem

Xylem Flojet G55 Series Bedienungsanleitung

Xylem

Xylem Bell & Gossett e-3530 Series Bedienungsanleitung

Xylem

Xylem Jabsco 18620-0003 Bedienungsanleitung

Xylem

Xylem FLYGT Compit 901 Series Bedienungsanleitung

Xylem

Xylem Lowara e-IXPSA Handbuch

Xylem

Xylem Goulds AquaBoost Advanced Bedienungsanleitung

Xylem

Xylem FLOJET BW5000 Series Bedienungsanleitung

Xylem

Xylem Flygt Top 50 Bedienungsanleitung

Xylem

Xylem Flygt 3085 Wartungshandbuch

Xylem

Xylem LOWARA Sekamatik 12MK7 Bedienungsanleitung

Xylem

Xylem LOWARA ecocirc PRO Bedienungsanleitung

Xylem

Xylem JABSCO 23920 Series Bedienungsanleitung

Xylem

Xylem Lowara Scuba Dry Series Handbuch

Xylem

Xylem DRAINAGE RED JACKET Series Handbuch

Xylem

Xylem FLYGT 3045 Wartungshandbuch

Xylem

Xylem Goulds AquaBoost VS Bedienungsanleitung

Xylem

Xylem Lowara Z8 Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

GÜDE

GÜDE HWW 900 GC Bedienungsanleitung