Yaesu VX-160U Bedienungsanleitung

VX-160U/180U

Alignment

VX-160U/180U Alignment

VX-160U/180U AlignmentVX-160U/180U Alignment

VX-160U/180U Alignment

The VX-160U/180U has been carefully aligned at the factory for the specified

performance across the frequency range specified for each version. Re-alignment should

therefore not be necessary except in the event of component failure, or altering version

type. All component replacement and service should only be performed by an authorized

VERTEX STANDARD representative, or the warranty policy may be void.

Required Test Equipment

Required Test EquipmentRequired Test Equipment

Required Test Equipment

CT-42 Programming Cable with CE44 Channel Programming Diskette

RF Signal Generator with calibrated output level at 1GHz

Deviation Meter (Linear Detector)

AC Voltmeter

SINAD Meter

In-Line wattmeter with 5 % accuracy at 500 MHz

Regulated DC Power Supply adjustable from 4 to 10 V, 3A

50ΩNon-reactive Dummy Load: 10 W at 500 MHz

Frequency Counter: ±0.2 ppm accuracy at 500 MHz

AF Signal Generator

DC Voltmeter: high impedance

Before beginning alignment, connect the transceiver and PC using the CT-42

Programming Cable, and run the CE44 Channel Programming Diskette, then download

the EEPROM data from the transceiver to the computer.

Then store this data in a disk file so that it can be uploaded when alignment is finished.

You should find the corresponding data file on the computer disk for the transceiver

version you are aligning, containing channel settings for the high edge, middle and low

edge of the transceiver’s frequency range in channels 1, 2 and 3, respectively. Up-load

this file to the transceiver.

Low Band Edge (Channel 1): 450.000 MHz

Band Center (Channel 2): 467.500 MHz

High Band Edge (Channel 3): 485.000 MHz

Note

NoteNote

Note

: Signal levels in dB referred in the alignment procedure are based on 0dBµ = 0.5

µV.

VX-160U/180U

Alignment

PLL & Transmitter

PLL & TransmitterPLL & Transmitter

PLL & Transmitter

Set up the test equipment as shown for transmitter alignment. Adjust the supply

voltage to 7.2 V for all steps where not specified otherwise.

PLL VCV (Varactor Control Voltage)

Connect the DC voltmeter between TP03 on the Main Unit and ground.

Set the transceiver to CH 3 (high band edge), and adjust L1004 on the Main Unit

for 4.1 V ± 0.1 V on the DC voltmeter.

Set the transceiver to CH 1 (low band edge), and confirm the low-end VCV is more

than 1.1 V while transmitting, and also while receiving.

PLL Reference

Set the transceiver to CH 2 (band center).

Open the “Adjust

AdjustAdjust

Adjust” window on the CE44, then select “Reference

ReferenceReference

Reference” parameter.

Press the [ENTER]key to enable programming of this parameter, use the [UP] or

[Down] arrow keys so that the frequency counter displays band center frequency

±100 Hz (for the version being aligned).

Transmitter Output Power

Set the transceiver to CH 2 (band center).

Open the “Adjust

AdjustAdjust

Adjust” window on the CE44, then select “TX Hi Power

TX Hi PowerTX Hi Power

TX Hi Power” parameter.

Press the [ENTER]key to enable programming of this parameter, use the [UP] or

[Down] arrow keys so that the power meter reading is 5 W. Confirm that the

current consumption is 2.0Aor below.

Select “TX Low Power” parameter.

Press the [ENTER]key to enable programming of this parameter, use the [UP] or

[Down] arrow keys so that the power meter reading is 1 W. Confirm that the

current consumption is 1.0Aor below.

Modulation Level

Set the transceiver to CH 2 (band center).

Inject a 1 kHz tone at 77 mVrms to the MIC jack.

Open the “Adjust

AdjustAdjust

Adjust” window on the CE44, then select “Modulation

ModulationModulation

Modulation” parameter.

Press the [ENTER]key to enable programming of this parameter, use the [UP] or

[Down] arrow keys so that the deviation meter reading is ±4.2 kHz (for 25 kHz

steps) or ±2.1 kHz (for 12.5 kHz steps) deviation.

VX-160U/180U

Alignment

Receiver

ReceiverReceiver

Receiver

Set up the test equipment as shown for receiver alignment.

Sensitivity

Set the transceiver to CH 3 (high band edge)

Tune the RF signal generator to the same frequency of the transceiver, then set the

generator output level to 40 µV with ±3.0 kHz deviation @ 1 kHz tone modulation.

Open the “Adjust

AdjustAdjust

Adjust” window on the CE44, then select “Sensitivity

SensitivitySensitivity

Sensitivity” parameter.

Press the [ENTER]key to enable programming of this parameter, use the [UP] or

[Down] arrow keys so that the RF signal generator output level should be –7dB or

less for 12 dB SINAD.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Yaesu Transceiver Handbücher

Yaesu

Yaesu FT-5100 Handbuch

Yaesu

Yaesu FT-8000R Bedienungsanleitung

Yaesu

Yaesu FT-890 Bedienungsanleitung

Yaesu

Yaesu FT-736R Bedienungsanleitung

Yaesu

Yaesu FT-757GX II Bedienungsanleitung

Yaesu

Yaesu FT-757GX II Bedienungsanleitung

Yaesu

Yaesu FTM-300DR Bedienungsanleitung

Yaesu

Yaesu FT-230R Bedienungsanleitung

Yaesu

Yaesu FT-2400H Bedienungsanleitung

Yaesu

Yaesu FT-900 Bedienungsanleitung

Yaesu

Yaesu FT-901DM Bedienungsanleitung

Yaesu

Yaesu FT-7800R Bedienungsanleitung

Yaesu

Yaesu FT-3000M Bedienungsanleitung

Yaesu

Yaesu FTDX5000 - SOFTWARE UPDATE INFORMATION... Technisches Handbuch

Yaesu

Yaesu FTDX-9000 - CAT OPERATION REFERENCE BOOK Service-Handbuch

Yaesu

Yaesu FT 201 Bedienungsanleitung

Yaesu

Yaesu FT DX 9000 - CAT OPERATION REFERENCE BOOK Service-Handbuch

Yaesu

Yaesu FT DX 9000 CONTEST - 2 Handbuch

Yaesu

Yaesu FT-416 Bedienungsanleitung

Yaesu

Yaesu FT-2000D - UPDATE V0150 AND V11.53 Technisches Handbuch

Yaesu

Yaesu FT-891 Bedienungsanleitung

Yaesu

Yaesu VX-3E Bedienungsanleitung

Yaesu

Yaesu FTM-200DR Bedienungsanleitung

Yaesu

Yaesu FT2DR Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung