Yamaha AVENTAGE RX-A1060 Gebrauchs- und Pflegehandbuch

Choose from the following 2 methods to update to the latest firmware.

Click here for Firmware Update Through the Internet

(Connection to the Internet is required)

Click here for Firmware Update by USB

(A USB thumb drive is required)

In case of error, see the Troubleshooting section

IMPORTANT NOTICE

Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the

Yamaha website or through your network connection.

Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by

Yamaha.

Improperly updated products may cause improper operation, and any parts or service required to restore proper

operation will not be covered under the Yamaha Limited Warranty.

FIRMWARE UPDATING PROCEDURE

MAIN ZONE key

Enter the ADVANCED SETUP mode

PROGRAM key

Firmware Update Through the Internet

Requirement: Internet connection

Your receiver is connected to the Internet if you can receive Internet radio stations.

(See owner’s manual for details)

Power off the receiver (Standby mode)

Select “FIRM UPDATE” from the menu

Start firmware update

While pressing the STRAIGHT key, press the MAIN ZONE key and keep STRAIGHT key pressed until

“

ADVANCEDSETUP

” appears on the front panel display.

*“

ADVANCEDSETUP

” is displayed only for a few seconds.

a. Press the PROGRAM key until “

FIRM UPDATEUSB

” is displayed.

b. Then, press STRAIGHT key until “

NETWORK

” is displayed.

a. Press INFO (WPS) key to start the update.

(Update process may take up to 15 minutes)

*If “

UPDATE SUCCESS

” appears, this means your receiver is already up-to-date. In this case, power off to

exit from Advanced Setup. Your AV receiver is ready for normal use.

Firmware update in progress

Caution

DO NOT interrupt power during the update.

In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to

the troubleshooting method (Troubleshooting CASE 2) on the last page.

b. When completed, “

UPDATESUCCESS

”, “

PLEASE...

”and “

POWEROFF!

” appears on the display.

c. Turn off the power of the receiver by pressing the MAIN ZONE key.

INFO (WPS) key

STRAIGHT key

(The design may differ by models.)

Check the updated firmware version

a. Power on the AV receiver and press the ON SCREEN key on the remote control.

b. Select “Information” > “System”.

c. Confirm that the firmware version is updated to the latest version.

ON SCREEN key

Congratulations!

You have completed the firmware update. Your AV receiver is ready for normal use.

Firmware Update by USB

Requirement: USB thumb drive, with enough free space to store the firmware.

(File system with FAT16 or FAT32 format)

Firmware file provided by YAMAHA, “R0411-xxxx.bin”.

Prepare USB thumb drive for the update

Download the firmware, unzip and copy “R0411-xxxx.bin” into the root directory of the USB thumb drive.

Drag & Drop the file into USB thumb drive.

Power off the receiver (Standby mode)

Insert the USB thumb drive

USB port is located at the lower left corner of the front panel.

Enter the ADVANCED SETUP mode

While pressing the STRAIGHT key, press the MAIN ZONE key and keep STRAIGHT key pressed until

“

ADVANCEDSETUP

” appears on the front panel display.

Select firmware update from the menu

Press the PROGRAM key until “

FIRM UPDATEUSB

” is displayed.

USB port

STRAIGHT key

PROGRAM key

MAIN ZONE key

R0411-xxxx.bin

(The design may differ by models.)

Start firmware update

a. Press INFO (WPS) key to start the update.

(Update process may take up to 10 minutes)

*If “

UPDATE SUCCESS

” appears, this means your receiver is already up-to-date. In this case, power off to

exit from Advanced Setup. Your AV receiver is ready for normal use.

Firmware update in progress

Caution

DO NOT interrupt power during the update.

In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to

the troubleshooting method (Troubleshooting CASE 2) on the last page.

b. When completed, “

UPDATESUCCESS

”, “

PLEASE...

”and “

POWEROFF!

” appears on the display.

c. Turn off the power of the receiver by pressing the MAIN ZONE key.

Check the updated firmware version

a. Power on the AV receiver and press the ON SCREEN key on the remote control.

b. Select “Information” > “System”.

c. Confirm that the firmware version is updated to the latest version.

ON SCREEN key

Congratulations!

You have completed the firmware update. Your AV receiver is ready for normal use.

USB port

MAIN ZONE key

INFO (WPS) key

(The design may differ by models.)

CASE 1

Error message appeared during the update

Cause: For some reason, the receiver can’t read the firmware data.

Method: For your solution, check the following

[Update through Internet]

❏

Check Internet connection.

Your Internet connection is working by playing an Internet radio station.

(See owner’s manual for details)

[Update by USB thumb drive]

❏

USB thumb drive is connected properly to the receiver.

❏

USB thumb drive is not password protected.

(AV receiver cannot read data from a security protected USB thumb drive)

❏

Make sure the USB thumb drive is inserted before the receiver is powered on for the

update.

❏

The firmware data, R0411-xxxx.bin is stored in the root directory of the USB thumb drive.

❏

There is no other data except the firmware data in the USB thumb drive.

❏

No folders are created in the USB thumb drive.

Else, retry the update by USB using another USB thumb drive.

CASE 2

Firmware update doesn’t start for other reasons

●Receiver doesn’t power up after the update.

●Or, error message appeared when confirming the firmware version.

Recovery method using USB method:

1. Unplug the AC power cable from wall outlet.

2. Insert the USB thumb drive which has the firmware data stored inside, into the USB port

located on the front panel.

3. Press and hold the PURE DIRECT key and keep it pressed while you plug the AC power

cable back into the wall outlet again.

“

FIRM UPDATE USB

” will appear on the front display. Then, release the PURE

DIRECT key.

4. The update will start automatically.

5. When “

UPDATE SUCCESS

”, “

PLEASE...

”, “

POWEROFF!

” appears on the

display, firmware update is completed.

Power off the receiver and remove the USB thumb drive.

6. Confirm updated firmware version.

PURE DIRECT key

USB port

Troubleshooting

(The design may differ by models.)

Andere Handbücher für AVENTAGE RX-A1060

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Yamaha Empfänger Handbücher

Yamaha

Yamaha SR-PGB54P Bedienungsanleitung

Yamaha

Yamaha RX-V430 Bedienungsanleitung

Yamaha

Yamaha RX-V396RDS Bedienungsanleitung

Yamaha

Yamaha RX-V675 Bedienungsanleitung

Yamaha

Yamaha RX-V396 Bedienungsanleitung

Yamaha

Yamaha htr-5890 Bedienungsanleitung

Yamaha

Yamaha RX-V659 Bedienungsanleitung

Yamaha

Yamaha RXV463BL Bedienungsanleitung

Yamaha

Yamaha RX-V650 Bedienungsanleitung

Yamaha

Yamaha RX-A3000 Bedienungsanleitung

Yamaha

Yamaha RX-V2400RDS Bedienungsanleitung

Yamaha

Yamaha HTR-5835 Bedienungsanleitung

Yamaha

Yamaha HTR-4065 Bedienungsanleitung

Yamaha

Yamaha HTR-5750 Bedienungsanleitung

Yamaha

Yamaha RP-U200 Bedienungsanleitung

Yamaha

Yamaha RX-V2400 Bedienungsanleitung

Yamaha

Yamaha Piano Craft RX-E600 Bedienungsanleitung

Yamaha

Yamaha RX V365 - AV Receiver Bedienungsanleitung

Yamaha

Yamaha MusicCast R-N2000ASL Bedienungsanleitung

Yamaha

Yamaha YHT-693 Bedienungsanleitung

Yamaha

Yamaha RX-V795RDS Bedienungsanleitung

Yamaha

Yamaha R-N1000A Bedienungsanleitung

Yamaha

Yamaha Piano Craft RX-E600 Bedienungsanleitung

Yamaha

Yamaha HTR-5940 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung