Yamaha RX V3900 - AV Network Receiver Gebrauchs- und Pflegehandbuch

Firmware Update Procedure for RX-V3900

Page.1 of 6

February, 2010

Subject: RX-V3900 Firmware Update ver. 1.11

Yamaha is pleased to offer this firmware update to ensure the best possible

performance for your Yamaha RX-V3900 AV Receiver.

This firmware improves HDMI standby through function.

The following pages contain the firmware update instructions for the RX-V3900.

You can easily update the latest firmware either by using an USB thumb drive, or

by connecting the receiver to the Internet. In order to properly execute the update,

read all instructions carefully. The following links will also lead you directly to the

beginning of each individual section of the instructions.

9Click here to confirm the current firmware version before the update.

9Click here for the firmware update by USB thumb drive.

(Update by Network is recommended if your receiver is connected to the internet)

9Click here for the firmware update by Network.

9Click here for the firmware version confirmation after update.

9Click here for troubleshooting.

< IMPORTANT NOTICE >

Do not attempt to update your Yamaha receiver using any other data file except those provided

directly from the Yamaha website or through your network connection.

Follow the instructions carefully and do not attempt any other procedures not specified in the

instructions provided by Yamaha.

Improperly updated products may cause improper operation, and any parts or service required

to restore proper operation will not be covered under the Yamaha Limited Warranty.

Firmware Update Procedure for RX-V3900

Page.2 of 6

Confirming the firmware version

Step1: Set the MASTER ON/OFF button on the front panel to OFF, and confirm that

the AC power cable is properly connected to an outlet.

Step2 While pressing the STRAIGHT button, press (and release) the MASTER

ON/OFF button and then keep pressing the STRAIGHT key until

“ADVANCED SETUP” appears on the front panel display.

(Note: “ADVANCED SETUP” is only displayed for a few seconds.)

Step3 Rotate the PROGRAM selector counterclockwise to select “VERSION”.

Latest version would be “VERSION 1.11”.

If your receiver’s version is lower than above, perform the update described in

the following pages. NETWORK UPDATE is recommended if your receiver

is connected to the internet. If not, perform USB UPDATE.

If “ERROR” appears, refer to the troubleshooting procedures on page 6 and

retry the update.

STEP1 STEP2

ress & hold

STEP3

Firmware Update Procedure for RX-V3900

Page.3 of 6

Instruction for USB Update

Step1: Delete any existing files in the USB thumb drive.

Step2: Copy the downloaded firmware “RXV3900-xxxx.bin” into the root directory of

the USB thumb drive.

Step3: Set the MASTER ON/OFF button on the front panel to OFF, and confirm that

the AC power cable is properly connected to an outlet.

Step4: Insert the USB thumb drive in the USB terminal located on the front panel.

While pressing the STRAIGHT button, press (and release) the MASTER

ON/OFF button and then keep depressing the STRAIGHT button until

“ADVANCED SETUP” appears on the front panel display.

(Note: “ADVANCED SETUP” is only displayed for a few seconds.)

Requirement: (Formatting by FAT system is required in advance).

- USB thumb drive, with enough free space to store over 16 MB.

- Firmware file provided by YAMAHA,”RXV3900-xxxx.bin”.

Drag & Drop the file into USB drive.

STEP3 STEP4

press & hold

Insert USB thumb

drive with

RX-V3900.bin file

Firmware Update Procedure for RX-V3900

Page.4 of 6

Step5 Rotate the PROGRAM selector counterclockwise to select “FIRM UPDATE

USB”.

Step6 To start the firmware update, press the MENU button.

(Allow about 10 minutes for the update)

Firmware reprogramming in progress

Caution! Do not interrupt power or remove the USB thumb drive during the update.

In case the power is accidentally cut off, refer to troubleshooting

procedures on page 6 to recover.

Step7 When “UPDATE OK” appers on the display, firmware update is completed.

The receiver automatically powers off and on again in normal operation

mode.

Step8 Power OFF the unit by pressing MASTER ON/OFF button on the front panel.

Remove the USB thumb drive.

Step9 Check the updated firmware version.

STEP6

STEP8

STEP5

Firmware Update Procedure for RX-V3900

Page.5 of 6

Instruction for Network Update

Step1: Set the MASTER ON/OFF button on the front panel to OFF, and confirm that

the AC power cable is properly connected to an outlet.

Step2: While pressing the STRAIGHT button, press (and release) the MASTER

ON/OFF button and then keep depressing the STRAIGHT button until

“ADVANCED SETUP” appears on the front panel display.

(Note: the “ADVANCED SETUP” is only displayed for a few seconds.)

Step3 Rotate the PROGRAM knob counterclockwise to select “FIRM UPDATE

USB”.

Press STRAIGHT button to change update mode to network.

Step4 To start the firmware update, press the MENU button. (allow about 10mins)

Firmware reprogramming in progress

Caution! Do to not interrupt power during the update.

Step5 When “UPDATE OK” appers on the display, firmware update is completed.

The receiver automatically powers off and on again in normal operation

mode.

Step6 Power OFF the unit by pressing MASTER ON/OFF button on the front panel.

Step7

Check the updated firmware version.

Requirement: Network environment to be able to connect to the Internet via

RX-V3900. (For more information, refer to the owner’s manual.)

STEP1/STEP6

STEP3

STEP4

STEP2 press & hold

Firmware Update Procedure for RX-V3900

Page.6 of 6

Troubleshooting Firmware Update

Case #1: Instead of “UPDATE OK”, an error message appeared on the display during

updating or “ERROR” appeared when confirming the firmware version in

Advanced Setup.

To recover, retry the update procedure of USB/Network from first step again.

In case the update has failed with network method, perform USB update method

for recovery.

Case #2: “Thumb Data Err” / “Firm Update” appeared on the display.

To recover,

1. Press MENU button. “FirmUpdate, push MENU key” will appear on the display.

2. Unplug the USB thumb drive and copy the update file again.

3. Insert the USB thumb drive in the USB terminal on the front panel.

4. Start firmware update by pressing the MENU button.

5. When “UPDATE OK” appears on the display, firmware update is completed.

System will reboot automatically.

6. Power OFF the unit by pressing MASTER ON/OFF button on the front panel.

7. Remove the USB thumb drive.

Case #3: Firmware update doesn’t start for other reasons.

For example, the unit does not power up after the MASTER ON/OFF

button is pressed. Or, “DEVICE ERROR” appeared on the front

display.

To recover,

1. Unplug the AC power cable from the back of the receiver.

2. Set the MASTER ON/OFF button on the front panel to ON.

3. Insert the USB thumb drive in the USB terminal located on the front panel.

4. Press and hold the INFO key and keep it pressed while you plug the AC power

cable back into the receiver again. The front panel display shows

“FirmwareUpdate”

5. The update will start automatically.

6. When “UPDATE OK” appears on the display, firmware update is completed.

System will turn off and on again automatically.

7. Power OFF the unit by pressing MASTER ON/OFF button on the front panel.

8. Remove the USB thumb drive.

STEP4

press &

hold

Andere Handbücher für RX V3900 - AV Network Receiver

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Yamaha Empfänger Handbücher

Yamaha

Yamaha RX-V730RDS Bedienungsanleitung

Yamaha

Yamaha RX-V740RDS Bedienungsanleitung

Yamaha

Yamaha V665 - RX AV Receiver Bedienungsanleitung

Yamaha

Yamaha RX-V861 Bedienungsanleitung

Yamaha

Yamaha RX-V367 Bedienungsanleitung

Yamaha

Yamaha RXA830 Installationsanleitung

Yamaha

Yamaha RXV765 - RX AV Receiver Gebrauchsanweisung

Yamaha

Yamaha AVENTAGE RX-A2050 Kurzanleitung

Yamaha

Yamaha RX-V565BL Bedienungsanleitung

Yamaha

Yamaha BRX-610 Bedienungsanleitung

Yamaha

Yamaha RX-Z9 Bedienungsanleitung

Yamaha

Yamaha HTR-5750 Bedienungsanleitung

Yamaha

Yamaha RN1000ASL Bedienungsanleitung

Yamaha

Yamaha RX-V730RDS Bedienungsanleitung

Yamaha

Yamaha r-s202 Bedienungsanleitung

Yamaha

Yamaha RX-V595 Bedienungsanleitung

Yamaha

Yamaha RX V565 Bedienungsanleitung

Yamaha

Yamaha HTR-5063 Bedienungsanleitung

Yamaha

Yamaha R-V1103 Bedienungsanleitung

Yamaha

Yamaha RX-V550 Bedienungsanleitung

Yamaha

Yamaha HTR-5935 Bedienungsanleitung

Yamaha

Yamaha RX-V350 Bedienungsanleitung

Yamaha

Yamaha RX-N600D Bedienungsanleitung

Yamaha

Yamaha RX-V2067 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung