Yealink SIP-T42U Bedienungsanleitung

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Video Tutorial

■

3 Requirements

■

3.1 Identifying Phone Model

■

3.2 Phone Firmware

■

3.3 DHCP Server

■

3.4 PBXware Version

■

4 Installation

■

4.1 Power Adapter

■

4.2 Power over Ethernet (PoE)

■

4.3 Find the phone IP address

■

4.4 Reset to Factory Settings

■

5 Registering Phone

■

5.1 Manual Configuration

■

5.2 Auto Provisioning

■

5.3 Using TLS

■

5.4 DNS SRV

■

6 Configure BLF

■

6.1 Extension Settings

■

6.2 Phone Settings

■

7 Additional Configuration Template

■

Introduction

This Configuration Guide is written as a general guide on how to configure the Yealink phone

model SIP-T42U to work with PBXware 5.3.6.

Video Tutorial

Please refer to the video tutorial explaining the Auto Provisioning setup for the Yealink Phone on

PBXware 5.

Requirements

Identifying Phone Model

To start and successfully complete registration of your Yealink phone you need to know which

phone model to set up.

On the back of each Yealink phone, there is model information that you should check. Although

various phone models can have exactly the same requirements and installation procedures,

phone models can also have significantly different requirements and installation procedures, so

that is why it is important to know the model you own which results in you setting up the device

successfully.

Phone Firmware

Make sure that your phone is loaded with an appropriate firmware version, 108.84.0.30.

■

To find out the firmware version of your Yealink phone model, open a new browser window

■

and enter your phone IP address in order to access the phone's web administration interface

■

note that the factory default login details are as follows: username is admin and password is

admin.

DHCP Server

Fully configured and operational DHCP server.

PBXware Version

PBXware version 5.3.6

In order to find out the PBXware version:

■

Navigate to Settings: About.

■

On the top of About page, you may see a code similar to this one PBXware Edition: Business,

Release: 5.3.6 (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v5.3.6

(62b7bcd), API: 5.3, libmemcached version: 1.0.14, where Release denotes the current

version of your PBXware.

Installation

This section describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power Adapter

■

Power over Ethernet (PoE)

■

Factory Settings

■

Power Adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the Ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Power over Ethernet (PoE)

Connect the Network (only)

Using a regular Ethernet cable, your phone can be powered from a Power over Ethernet (PoE)

compliant router or switch.

Connect the Ethernet cable between the Internet port on the phone and an available port on

■

the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Find the phone IP address

Find out your Yealink phone IP Address.

Press the Menu keysoft.

■

Press the Enter keysoft to enter 1. Status.

■

The IP address will be displayed on the top of the display.

Reset to Factory Settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been

already used then it is a must.

Open a new browser window and enter your phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22.

■

note that the factory default login details are as follows: username is admin and password is

admin.

Click the Upgrade tab.

■

Click the Reset button in order to reset the phone to factory settings. A phone will reset to the

■

factory settings and reboot.

Wait some time for a device to reboot.

■

NOTE: Do not unplug or remove power from the phone while it is updating firmware and

configuration..

Registering Phone

This section describes how to identify the Yealink phone model, requirements that must be met,

and how to register a phone using Manual configuration or Auto provisioning.

The following topics are covered:

Manual Configuration

■

Auto Provisioning

■

Manual Configuration

This section describes how to set UAD settings, create the PBXware Extension, and register the

phone.

The following topics are covered:

UAD settings

■

Creating Extension

■

Registering Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings: UAD.

■

Make sure that the Yealink UAD is enabled. To check the UAD status, click the Edit icon

■

corresponding to your Yealink phone.

Make sure that Status is set to Active, Auto provisioning is set to No, and DHCP is set to

■

Yes.

Click the Save button to save changes.

■

Creating Extension

Add the Extension

Navigate to Extensions. Click the Add Extension button.

■

The standard options window will be shown below.

■

Select the Yealink phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Department

■

Define the Department to which the Extension belongs to. Example: Sales.

Click the Save button.

■

Registering Phone

This section describes how to register the Yealink phone using Hostname or IP Address, or

DNS SRV.

The following topics are covered:

Hostname or IP Address

■

DNS SRV

■

Hostname or IP Address

Open a new browser window and enter your phone IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22

■

note that for factory default login details, the username is admin and the password is admin.

Click Accounts.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Account Active

■

Make sure that the On radio box is selected.

■

Enter the PBXware Extension number. Example: 1003

User Name

■

Usually refers to the same number as the Phone Number.

Password

■

The Secret of the Extension as received in the e-mail associated with this Extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

Extension.

Sip Server

■

Enter the Hostname or IP Address of PBXware.

- Example of a Hostname: voip.bicomsystems.com

- Example of an IP Address: 192.168.1.10

Click the Confirm button.

■

You will have to wait some time for the device to reboot. If everything is done as described

■

above, you should have successfully registered your phone to PBXware.

Dial *123 to verify registration.

DNS SRV

This section describes how to use a DNS SRV record which specifies the location of PBXware.

NOTE: Your DNS Server needs to be configured correctly in order for this to work. Bicom

Systems can provide service to set up this for you.

Open a new browser window and enter your phone IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22

■

note that the factory default login details are as follows: username is admin and password is

admin.

Click Account.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Account Active

■

Make sure that the On radio box is selected.

■

Enter the PBXware Extension number. Example: 1003

User Name

■

Usually refers to the same number as the Phone Number.

Password

■

The Secret of the Extension as received in the e-mail associated with this Extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

Extension.

Sip Server

■

In the Sip Server field, enter the Hostname.

- Example of a Hostname: bicomsystems.com

Make sure that you replace Hostname from this example with your PBXware Hostname.

■

Make sure that DNS server is configured to automatically route registration request to

■

PBXware which is actually under another domain name. Example: newbicomsystems.com.

Transport

■

Select DNS SRV from the drop-down menu.

Click the Confirm button.

■

You will have to wait some time for the device to reboot. If everything is done as described

■

above, you should have successfully registered your phone to PBXware.

Dial *123 to verify registration.

Auto Provisioning

This section describes how to set UAD settings, create the PBXware Extension, and register the

phone using DHCP or Static IP address.

The following topics are covered:

UAD Settings

■

Creating Extension

■

Registering Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings: UAD.

■

Make sure that the Yealink UAD is enabled. To check the UAD status, click the Edit icon

■

corresponding to your Yealink phone.

Make sure that Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to

■

Yes.

Click the Save button to save changes.

■

Creating Extension

Add the Extension

Navigate to Extensions. Click the Add Extension button.

■

The standard options window will be shown below.

■

Select the Yealink phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet etc.

Click the Next step button.

■

Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter Yealink phone MAC address. Example: 001565FF1536. MAC address can be found

at the back of the phone.

Click on the Save button.

■

Registering Phone

This section describes how to register Yealink phone using DHCP, TFTP, HTTP & HTTPS, or

DNS SRV.

The following topics are covered:

DHCP

■

TFTP or HTTP & HTTPS

■

DNS SRV

■

DHCP

Configure DHCP

Make sure that your DHCP router is configured to use option 66 to automatically instruct

■

phones with the URL for Auto provisioning. For more information, please refer to your router

documentation or contact your network administrator.

Andere Handbücher für SIP-T42U

Inhaltsverzeichnis

Andere Yealink IP-Telefon Handbücher

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Yealink

Yealink Yealink SIP-T26P Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Yealink

Yealink Yealink SIP-T28P Bedienungsanleitung

Yealink

Yealink SIP-T41S Bedienungsanleitung

Yealink

Yealink Yealink SIP-T21P Bedienungsanleitung

Yealink

Yealink W73P Gebrauchsanweisung

Yealink

Yealink CP860 SERIES Service-Handbuch

Yealink

Yealink Yealink SIP-T20P Bedienungsanleitung

Yealink

Yealink T48G Bedienungsanleitung

Yealink

Yealink T20P Bedienungsanleitung

Yealink

Yealink SIP-T19(P) E2 Bedienungsanleitung

Yealink

Yealink SIP VP-T49G Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Yealink

Yealink T46G Skype For Business Edition Bedienungsanleitung

Yealink

Yealink SIP-T54W Bedienungsanleitung

Yealink

Yealink Yealink SIP-T41P Bedienungsanleitung

Yealink

Yealink T40P Bedienungsanleitung

Yealink

Yealink Verizon One Talk W60B Bedienungsanleitung

Yealink

Yealink Telkom W52P Bedienungsanleitung

Yealink

Yealink Yealink SIP-T42G Bedienungsanleitung

Yealink

Yealink SIP-T23P Bedienungsanleitung

Yealink

Yealink SIP-T41S Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung

Fiberme

Fiberme FAP260 Series Bedienungsanleitung