Yoshimura RACE SERIES Bedienungsanleitung
RESEARCH&DEVELOPMENT OF AMERICA, INC.
NOTE: IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM, WHICH INCLUDES THE CARBURETORS OF ANY VEHICLE.
You must know how to remove and replace your stock exhaust in order to install this product
otherwise have it installed by a professional mechanic. Keep all stock parts from your existing
system as some components may be necessary to install your new Yoshimura exhaust depending
on the application. Read through all instructions before beginning installation. Exhaust system can
be extremely hot. Let motorcycle cool down before beginning installation. Always wear hand and
eye protection and take precautionary measures to avoid injury.
RACE SERIES
13630AP520 (SS/CF)
136301P720 (TI/CF)
Alpha Taper Full-System
Yamaha R6
Qualified Manufacturer Declared “Modified Part ”
FOR CLOSED COURSE COMPETITION ONLY; NOT INTENDED FOR STREET USE
2006~2017
Race Series systems are:
• NOT CARB/EPA tail-pipe emissions compliant.
• NOT street legal.
• For “Closed Course Competition” use only.
Assembly Diagram
2
** Not shown on the diagram.
**** Not compatible with European model.
NO. DESCRIPTION QTY PART #
1 Yoshimura Stainless Steel Manifold 4 13630SDM
2 Yoshimura Aluminum Flange 4 YZ616SDR-04
Yoshimura Stainless Steel Header 13630-404
Yoshimura Titanium Header 13630-704
Yoshimura Stainless Steel Tailpipe 13630-419
Yoshimura Titanium Tailpipe 13630-719
Yoshimura Stainless Steel Muffler 13630AP520-RMA
Yoshimura Titanium Muffler 136301P720-RMA
6 8mm Flanged Nut 2 8MMNUT
7 Medium Exhaust Spring 10 RACE-SPS-1
8 O2 Sensor Bung Plug 1 M18X9PLG
** Low Volume Sound Insert 1 INS-20-K
** Yoshimura Decal Sheet 1 17029
** Spring Puller Tool 1 ST-200
3 1
4 1
5 1
1
2
3
4
5
6
6
7
7
7
8
1. Remove left and right side fairing.
2. Remove the three bolts that secure the black
muffler protector, exposing the exhaust valves
and exhaust clamp.
3. Disconnect and remove the exhaust valve
cables (refer to your service manual for
complete removal instructions).
Note: Do not unplug servo motor. Unplugging
the servo motor may cause the bike to
run in a power limited fail safe mode.
4. Loosen the stock exhaust clamp
5. While securely supporting the stock muffler,
remove the muffler mount bolt and carefully
remove the stock muffler assembly by sliding
toward the rear of motorcycle.
6. Remove O2 sensor from the stock header.
7. Remove the two header chassis mount bolts.
8. While securely supporting the stock header
assembly, remove header nuts and carefully
remove the stock header assembly.
Note: The stock exhaust port gaskets will not be
used with the Yoshimura full-system.
Remove gaskets from exhaust ports
before installing Yoshimura manifolds.
9. Remove the bolt securing left side muffler stay
to frame as it will not be used with the
Yoshimura full-system.
Removal
3
CAUTION: Exhaust system can be extremely hot.
Let motorcycle cool down before
beginning installation. Always wear
hand and eye protection and take
precautionary measures to avoid
injury.
WARNING: Always properly support vehicle with
a stand and/or lift when servicing or
performing any work. Unstable
vehicles may present dangerous
conditions and may cause property
damage and/or personal injury.
NOTE: Read through all instructions before
beginning installation. 1. Install (No. 1) 13630SDM, manifold and (No. 2)
YZ616SDR-04, flange onto exhaust port using
the stock header nuts. Do not torque at this time.
See below for proper orientation of flanges.
Note: Hook (No. 7) RACE-SPS-1, medium
exhaust springs onto flanges before
installing header. Access will be limited
once header is installed.
2. Install (No. 3) 13630-404/13630-704, header
onto manifolds by slipping one header leg at a
time from one end to the other. Using a rubber
mallet, gently tap header legs to make sure
header is fully seated onto the manifolds.
Remove Left Side Muffler Stay
Installation
2
1
Flange Orientation & Spring Location
Incorrectly SeatedCorrectly Seated
3. Torque header nuts to factory specification and
hook springs onto header legs.
4. Install (No. 4) 13630-419/13630-719, tailpipe
over header outlet. Align tailpipe bracket to the
backside of the right muffler stay and secure
using the stock bolt and supplied (No. 6)
8MMNUT, flange nut. Do not torque at this time.
5. Install (No. 5) muffler, over tailpipe outlet and
align muffler bracket to the backside of the
muffler mount. Secure using the stock muffler
mount bolt, washer, and (No. 6) 8MMNUT,
flange nut.
6. Torque muffler mount bolt to factory
specification.
7. Torque tailpipe chassis mount bolt to factory
specification.
8. Install (No. 7) RACE-SPS-1, medium exhaust
spring between muffler to tailpipe connection
and tailpipe to header connection.
9. Re-install the stock O2 sensor plug into (No. 4)
13630-419/13630-719, tailpipe. Torque to
factory specification.
10. Re-install left and right side faring using the
opposite steps of removal.
Note: For 2017 model, it may be necessary to
trim the left side corner of the lower cowl
if close to the header leg.
4
Stock Bolt
& Washer
Muffler
Bracket
6
Works Finish
Care & Maintenance
Before starting vehicle, clean pipe thoroughly using
a soft cloth and rubbing alcohol to remove any oil
and finger prints.
The color of the exhaust will change once the
system has gone through a heat cycle of 15
minutes or more. Color will vary depending on
lean/rich conditions.
Clean using a soft cloth and soap. Do not use
abrasive materials as it will scratch the surface.
Surface reconditioning services are available to
remove scratches and undesirable discoloration
due to extreme heat.
11. Before starting motorcycle, check for proper
clearance between new exhaust system and
rear suspension (i.e. tire, swing arm, brakes,
rear shock, and etc.) If any problem is found,
please carefully follow through the installation
steps again.
12. It is recommended that the muffler and tailpipe
be wiped down with rubbing alcohol to remove
oil and fingerprints. This will help prevent
tarnishing of the finish after the exhaust is
heated up.
Note: After starting motorcycle, it is normal for
new exhaust system and muffler to emit
smoke until oil residue burns off.
Looking for dependable exhaust parts?
Rely on Yoshimura for quality and long-lasting products.
Andere Yoshimura Motorradzubehör Handbücher
Yoshimura
Yoshimura ZX649SO Bedienungsanleitung
Yoshimura
Yoshimura Enduro Series Bedienungsanleitung
Yoshimura
Yoshimura RS-12 Bedienungsanleitung
Yoshimura
Yoshimura RACE 13100CP520 Bedienungsanleitung
Yoshimura
Yoshimura 070BG149500 Bedienungsanleitung
Yoshimura
Yoshimura RS-3 Bedienungsanleitung
Yoshimura
Yoshimura RACE Series Bedienungsanleitung
Yoshimura
Yoshimura ENDURO 24140AH320 Bedienungsanleitung
Yoshimura
Yoshimura RACE Series Bedienungsanleitung
Yoshimura
Yoshimura 570-400-0300 Bedienungsanleitung
Yoshimura
Yoshimura 070BG141503 Bedienungsanleitung
Yoshimura
Yoshimura RACE Series Bedienungsanleitung
Yoshimura
Yoshimura 070BG141200 Bedienungsanleitung
Yoshimura
Yoshimura 070BG131000 Bedienungsanleitung
Yoshimura
Yoshimura 15002B0520 Bedienungsanleitung
Yoshimura
Yoshimura 070BG139600 Bedienungsanleitung
Yoshimura
Yoshimura 224500D320 Bedienungsanleitung
Yoshimura
Yoshimura X-TREAD 559-592-V000 Bedienungsanleitung
Yoshimura
Yoshimura Signature Series Bedienungsanleitung
Yoshimura
Yoshimura 14720BP520 Bedienungsanleitung
Beliebte Motorradzubehör Handbücher anderer Marken
SRC
SRC B-TRK502-01-01-SL Bedienungsanleitung
3M
3M Speedglas 9100 MP Bedienungsanleitung
hepco & becker
hepco & becker 6307520 00 01 Bedienungsanleitung
HOMCOM
HOMCOM AA0-077 Bedienungsanleitung
hepco & becker
hepco & becker 6307558 00 01 Bedienungsanleitung
Wunderkind Custom
Wunderkind Custom 106503-F15 Benutzerhandbuch
