Zatech ZMCBR-H65 Bedienungsanleitung

ZMCBR-H65

General introduction

Preface

Please read this manual carefully before using your Digital Satmeter for the first time.

This operating manual will help you in the

• Appropriate,

• Safe

• Favorable

The technical specifications and operating methods included in this manual are

subject to changes without notice. In case of any inquires after a period of usage,

please contact the manufacturer.

+Safety Precaution

Please read the safety instructions carefully before operating the device.

Please follow all warnings and instructions on the equipment and in the operating

manual.

4 Safety of persons

Ensure that nobody can be hurt by falling tools or parts of the sate antenna during

the adjustment and installation of the antenna. For own security, use a rope on

sloping roofs.

4 Attention for adapter

The devise should only be operated with the supplied AC adapter at the mains. Do

not open the meter or the included AC adapter. There is danger of life through

electric shock! Wrong usage of the ports can lead to the destruction of the

measuring device.

4 Proceed carefully with the measuring device:

• Avoid low temperatures (below 0 °C) or to high humidity.

• The TFT display can be damaged by mechanical impacts.

• Avoid excessive input voltages. Please refer to the technical data

4 Do not operate with the device:

• If it has visible damage,

• If there are loose parts in the device,

• If the device was located outdoors or in damp rooms a extended period of time.

4 Main Supply:

Before operating, please check the units operating voltage is 90~240V AC 50/60Hz.

ZMCBR-H65

4 Overload:

Do not overload a wall outlet, extension cord or adapter, neither use damaged

power cord or touch it with wet hand as this may result in electric shock.

4 Liquid:

The receiver shall not be exposed to dripping or splashing water, and that no objects

filled with liquids, such as base, shall be placed on the apparatus.

4 Ventilation:

Keep the slots on top of the receiver uncover to allow sufficient airflow to the unit. Do

not put the receiver on soft furnishings or carpets. Do not expose there receiver to

direct light or do not place it near a heater or in humid conditions. Do not stack

other electronic equipments on top of the receiver.

4 Cleaning:

Plug out the receiver from the wall outlet before cleaning. Clean the receiver by a

soft cloth or mild solution of washing-up liquid (no solvents).

4 Location:

Put the receiver indoor in order to avoid lightening, raining or sunlight.

4 Uncover:

Do not remove the cover, to reduce the risk of electric shock. Contact qualified and

licensed service personnel to repair the receiver, or contact your dealer.

1. Reference

1.1 General Features

- DVB-S2 Compliant (MPEG-4), ISDB-T Complian

- MPEG-4 MPEG-2 Video (MP@ML), MPEG-1 Audio Layer1, Layer2

1.2 Brilliant on Screen Graphic

- User Friendly OSD Menu with Full Function

- Storing 8000 Channels

- USB 2.0 Host Controller

- Software Upgrade via USB

- Satellite Identify

- DiSEqC Search

- Spectrum

- Constellation

ZMCBR-H65

2. Product Overview

DVB S2/ ISDB-T

4. LOCK light：

This light will be on when signal is locked

5. 13V/18V light:

Indicate the 13V/18V

6. Function key：

Made of 4 keys, F1 - F4

7. Arrow key and OK key：

Press the Arrow key to select the right item then

press OK key to confirm

8. SYSTEM key：

Enter the settings menu, you can set all system

parameters products

9. AV IN key:

Use this product as a television

10. FIND key:

Enter the menu of measurement signal, you can

measure the signal about transponder quickly.

11. MENU key:

Enter the main menu

12. EXIT key：

Exit from the present menu and back to the

previous menu

13. SCAN key：

In the S2 model, it is blind scan, in the ISDBT

model ,it is auto search

14. USB Port:

One USB Host Port

15.HDMI Port：

Use HDMI line connect to TV

15.ON/OFF：

Switch the battery on/off

1. POWER key:

Turn the product on/off

2. LCD Screen：

Shows Menus and Programs clearly

3. Power light：

Indicates the power status

Red: the product is power on

Green: the product is power off

ZMCBR-H65

3. Connection with Other Device

The following chapter shows you the connections among product, ANT and

other equipment, please read this first if you are not sure about the connection,

and it will guide you to the correct connection.

You can connect one receiver directly to the ANT IN.

4. Detailed operation Guide

You should installation the receiver when powering on your product for the first

time after purchase.

4.2 Satellite

Main Menu-> satellite

Press OK enter the satellite model

4.1 Powering On

1. Connect the power cord of the product to

a wall outlet.

2.Power on by pressing the POWER button on

the panel.

ZMCBR-H65

4.2.1 TP Search

Main Menu-> Satellite -> TP Search

Press OK enter the TP search, first, you should select satellite, in this picture, you also

can delete, move, and rename the satellite.

When you fixed on a satellite, then press OK the following window will appear. Use

[p/q] button to move cursor, it’ll show the satellite name, transponder, LNB, 22 KHz,

DiSEqC port. When all parameters confirm, press F2 button search the channels. You

also can press F1 to delete the sat, or press F3 to view the constellation, or press F4 to

explorer the signal information.

You can display constellation by F3 button.

4.2.2 Satellite IDE.

Main Menu-> Satellite ->Satellite IDE.

If you don’t know the signal information of some usual sat, in this menu, please wait a

moment, it will find the satellite identify.

4.2.3 Packet Control

Main Menu-> Satellite -> Packet Control

In this menu, you can know the strength and

quality of each transponder under the

satellite.

ZMCBR-H65

4.2.4 DiSEqC Search

Main Menu-> Satellite -> DiSEqC Search

Press OK enter the DiSEqC search, in this menu, connect the DiSEqC port, the view

will be display the sat which can connect, then you can search the channel by

DiSEqC. Press F4 button to switch LNB Type.

4.2.5 Motor Search

Main Menu-> satellite -> Motor

Press OK enter the Motor search, select

satellite and any transponder, if signal and

quality OK press F3 button to start search, press

F1 button turning Motor to west. Press F2 button

turning Motor to east. Press the F4 button you

can search by Motor; however, you should set

up the Angle about the sat use the Angle

button first of all.

4.2.6 Spectrum

Main Menu-> satellite -> Spectrum

In this menu, you can know the strength of all transponders.

Press the F1 button to keep the spectrum , and press the F2 button to analyze

spectrum , and press the F3 button to mark spectrum , and press F4 button to next

page.

Press the F1 button to change Polarization control Hor / Ver, and press F2 button to

switch 22khz signal on or off, and Press the F3 button to switch DiSEqC , and press F4

button to previous page .

ZMCBR-H65

4.3 TERRESTRIAL

Main Menu-> TERRESTRIAL

Press OK enter the terrestrial model

4.3.1 TP Search

Main Menu-> TERRESTRIAL-> TP Search

In this menu, you can Delete, Add, Manual Search,

Auto Search transponders.

- Delete

In this menu, when you highlight the channel item,

you can press the t/u key to choose the transponder

which you want to delete, then press the F1 key to

delete.

- Add

You can add the transponder which you want with the F2 key. Here you can input

new Frequency, Bandwidth. Press the OK key to confirm the setting, then this new

transponder will be added to the Transponder list.

- Search

You can Manual Search the transponder which you want with the F3 key. You will

be asked to confirm whether only search FTA channels or not. If you select “Yes”,

you will only search FTA channels.

- Auto Search

You can search all transponders with the F4 key.

ZMCBR-H65

4.3.2 TP IDE

Main Menu-> TERRESTRIAL-> TP IDE.

In this menu, you can know the exact

information about the transponder and you

can also Delete, Add, Manual Search, Auto

Search transponders .

1. SNR: It will show you the Carrier to Noise Ratio of the transponder you selected.

3. BER：Error Correction

5. Power: It will show you the strength of the transponder you selected.

6. Modulate: Modulation efficiency.

4.3.3 Packet Control

Main Menu-> TERRESTRIAL-> Packet Control

In this menu, you can know the strength

and quality of each transponder

4.3.4 Spectrum

Main Menu-> TERRESTRIAL->Spectrum

In this menu, you can know the strength of

all transponders.

1. t/u : Press the t/ukey to change the

transponder.

2. p/q : Press the p/qkey to change the

range of the Y-axis.

3. Span: Press the F3 key to set transponder

of span.

4. Save Spectrum: Press the F4 key to save

the picture of spectrum.

ZMCBR-H65

4.4 Watch TV

Main Menu-> Watch TV

Press OK enter the Watch TV menu, in this menu, you can press the F1 button to

select any satellite or press the F2 button to enter the Channel/Radio menu,

press the up/down key jump to next/previous channel.

Press the F3 button to watch Full Screen.

Press the F4 button to analyze program.

4.5 Settings

4.5.1 System

Main Menu-> Settings-> System

In this menu, you can set all the settings

here by pressing the t/ukey.

1. Menu Language: Set the menu

language.

2. Audio1: Set the preferred audio

language.

3. Audio2: Set the sub-prime audio

language.

4. Digital Audio: Select PCM / RAW as default output.

5. Power Out 12V: If you set it on, it will support 12V voltage.

6. DVBT Power: If you set it on, it will provide voltage for T tuner.

7. Signal Audio: If you set “ON”, in the TP Search interface when you highlight a

transponder with signal, it will sound automatically. If you set “OFF”, in the TP Search

interface when you highlight a transponder with signal, it will not sound.

8. Power Unit: Change the power unit.

ZMCBR-H65

4.5.2 OSD Setup

Menu->Settings>OSD Setup

1. Display Mode: Set the HD format between 1080p, 1080i, 720p, 480i, 480p.

2. TV Type: Set the TV Type on PAL/NTSC/Auto state.

3. Screen Mode: Set the display format according to the screen ratio. Select TV

screen mode either 4:3 or 16:9 according to the TV type, or press the MODE button of

RCU directly.

4.5.3 Times

Menu->Settings>Times

1. Time Settings

In this menu, you will set the time mode,

time zone and summer time

2. Sleep Timer

Set the time to make receiver sleep

automatically.

4.5.4 Factory Default

Main Menu-> Settings-> Factory Default

In this menu, you can restore the product to the factory default and also setup it

according to the wizard.

1. All: All data and settings will be deleted.

Tip: If you select “Yes” all data and setting will be lost. Then wait a moment, you will

enter the wizard menu where you can set the parameter according your mind.

2. Channel List Only: All channels data will be deleted.

3. Radio Channel Only: All radio channels data will be deleted.

4. Scramble Channel Only: All scramble channels data will be deleted.

4.5.5 Color Settings

Main Menu-> Settings-> Color Settings

You can set the Brightness/Contrast/Saturation in this menu.

4.5.6 Screen

Main Menu-> Settings-> Screen

In this menu, you can set up Sharpness/Brightness /Contrast/Saturation/LCD

Backlight/LED Backlight.

Inhaltsverzeichnis

Andere zatech Messgerät Handbücher

zatech

zatech ZMCE 1.1AD Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

zatech ZMCBR-H65 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken