Zebex A-50M+ Bedienungsanleitung
A-50M+
Omnidirectional Laser Scan Module
Service Guide
Revision History
Changes to the original manual are listed below:
Version Date Description of Version
1.0 June. 10, 2014 Initial release
1.1 November 07, 2019 Engine updated
1.2 March 1, 2020 Buzzer board updated
SERVICE GUIDE
Preface
Laser Safety
The Omnidirectional Laser Scan Module Scanner complies with safety standard IEC 60825 for a Class II laser
product. It also complies with CDRH as applicable to a Class IIa laser product. Avoid long term staring into direct
laser light.
Radiant Energy: The Miniature Dual-Laser Omnidirectional Hands-free Scanner uses two low-power visible laser
diodes operating at 650nm in an opto-mechanical scanner resulting in less than 3.9µW radiated power as observed
through a 7mm aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to
0.8mW would be accessible inside.
Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this
product. A failure of the scanner motor, while the laser diode continues to emit a laser beam, may cause emission
levels to exceed those for safe operation. The scanner has safeguards to prevent this occurrence. If, however, a
stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately.
Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing
of the scanner. There are no user-serviceable parts inside.
Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous laser light exposure.
Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include
binoculars, magnifying glasses, and microscopes but do not include normal eye glasses worn by the user.
For CE-Countries
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit
should be used in order to maintain CE conformance.
This manual is in A4 format. Please check your printer setting before printing it out.
A-50M+ Service Guide 2 / 7
SERVICE GUIDE
Table of Contents
Preface..........................................................................................................................................................................2
Laser Safety............................................................................................................................................................................2
Scanner Parts ..........................................................................................................................................................................4
Take Apart ....................................................................................................................................................................5
Before You Start ....................................................................................................................................................5
Important Instructions ..................................................................................................................................................5
Tools to Prepare .....................................................................................................................................................................5
A-50M+ Service Guide 3 / 7
A-50M+ Service Guide 4 / 7
SERVICE GUIDE
Scanner Parts
The scanner includes the following parts:
NO. P/N Name Quantity
1 864-A50MP0-307 Top case assembly 1
2 864-A50MBC-000 Bottom case assembly 1
3 864-A50MP2-710 Center mirror base assembly 1
4 031-006508-000 FFC cable 1
5 864-A50MP1-711 Buzzer+LED board assembly 1
6 603-2A50M0-201 Buzzer sealing rubber 1
7 563-A30600-091 PC board spacer 1
8 521-002000-8R0 Self tapping screw,M1.6-8.0mm 4
9 521-202000-4R0 Self tapping screw M1.6-4.0mm 2
10 689-100000-201 LED light guide panel 1
11 170-50R425-200
170-50U303-200
RS-232 cable
USB cable 1
SERVICE GUIDE
Take Apart
Before You Start
Important Instructions
Read these instructions completely before you begin.
Follow all instructions.
Heed all warnings.
Tools to Prepare
Philips screwdriver.
Please follow these steps to take apart A-50M+.
1. Unscrews the screws and remove the cover.
2. Separate the front and back cover then remove the FFC cable.
A-50M+ Service Guide 5 / 7
SERVICE GUIDE
3. Remove the screws pointed by the red arows.
4. Take out the sealing rubber.
5. Remove the center mirror base.
A-50M+ Service Guide 6 / 7
A-50M+ Service Guide 7 / 7
SERVICE GUIDE
6. Remove the cables in circle.
7. Remove the FFC cable.
Inhaltsverzeichnis
Andere Zebex Barcode-Lesegerät Handbücher
Zebex
Zebex Z-6170 Bedienungsanleitung
Zebex
Zebex Z-6010 Bedienungsanleitung
Zebex
Zebex ZB- 800 SERIES Bedienungsanleitung
Zebex
Zebex Z-3070 Series Bedienungsanleitung
Zebex
Zebex z3190BT Bedienungsanleitung
Zebex
Zebex Z-3392BT Bedienungsanleitung
Zebex
Zebex Z-325x Bedienungsanleitung
Zebex
Zebex Z-6070 Series Bedienungsanleitung
Zebex
Zebex Z-6182 Bedienungsanleitung
Zebex
Zebex Z-5130 Bedienungsanleitung
Zebex
Zebex Z-2130 Bedienungsanleitung
Zebex
Zebex Z-3191BT Bedienungsanleitung
Zebex
Zebex Z-900XBT Bedienungsanleitung
Zebex
Zebex Z-8072 Bedienungsanleitung
Zebex
Zebex Z-5160 Bedienungsanleitung
Zebex
Zebex Z-3052 Bedienungsanleitung
Zebex
Zebex Z-8082 Lite Bedienungsanleitung
Zebex
Zebex Z-5112 Bedienungsanleitung
Zebex
Zebex Z-5252 Bedienungsanleitung
Zebex
Zebex ZB-2200AM SERIES Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
