Zortrax M200 Gebrauchs- und Pflegehandbuch

Extruder Bearing Replacement

SOURCE:

https://support.zortrax.com/extruder-bearing-replacement/

page 1 / 24

Table Of Content

Unplugging the Power Cable 4

Material Guide Removal 5

Unplugging the Extruder Cable 6

Unplugging all Cables from the Extruder PCB 7

Unscrewing the Extruder PCB 8

Extruder Lower Printed Cover Removal 9

Unscrewing the Extruder Aluminum Cover 10

Unscrewing the Extruder Motor 11

Extruder Motor Removal 12

Unscrewing the Extruder Bearing 13

Extruder Bearing Removal 14

Extruder Bearing Assembly 15

Extruder Motor Assembly, part 1 16

Extruder Motor Assembly, part 2 17

Extruder Aluminum Cover Assembly 18

Extruder Lower Printed Cover Assembly 19

Extruder PCB Assembly 20

Plugging all Cables into the Extruder PCB 21

Plugging the Extruder Cable 22

Material Guide Installation 23

Plugging the Power Cable 24

page 2 / 24

The extruder bearing supports extrusion by pressing the material to the extruder

motor sprocket wheel during loading and the printing process. Therefore, when

the material in your printer is not being extruded when loading or printing, or the

sprocket wheel is making clicking sounds, the extruder bearing may be faulty and

should be replaced. Follow the steps from this manual to see the correct

replacement procedure.

If the material is loaded into the extruder, unload the material using the “Material” ->

“Unload material” option in the printer menu.

The following manual shows the M200 repair work. For the M300, these procedures are

the same.

page 3 / 24

Unplugging the Power Cable

Turn off the printer and unplug the power cable and wait a few minutes for all the

capacitors to discharge.

page 4 / 24

Material Guide Removal

Detach the material guide from the extruder cover. Next, separate the guide from the

extruder cable.

page 5 / 24

Unplugging the Extruder Cable

Detach the extruder upper printed cover and unplug the extruder cable.

page 6 / 24

Unplugging all Cables from the Extruder PCB

Unplug all the cables from the extruder PCB.

page 7 / 24

Unscrewing the Extruder PCB

Unscrew the two screws that secure the extruder PCB using a 2mm Allen key. Remove

the PCB from the extruder.

page 8 / 24

Extruder Lower Printed Cover Removal

Remove the extruder lower printed cover.

page 9 / 24

Unscrewing the Extruder Aluminum Cover

Unscrew the screws that secure the extruder aluminum cover on both sides of the

extruder. Separate the cover from the extruder motor.

page 10 / 24

Andere Handbücher für M200

22

Dieses Handbuch passt für folgende Modelle

1

Andere zortrax 3D-Drucker Handbücher

zortrax

zortrax M300 Betriebsanleitung

zortrax

zortrax Z-NYLON Montageanleitung

zortrax

zortrax M200 Gebrauchs- und Pflegehandbuch

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M200 Plus Bedienungsanleitung

zortrax

zortrax M200 Gebrauchs- und Pflegehandbuch

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax Inventure Bedienungsanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax Apoller Bedienungsanleitung

zortrax

zortrax Endstop Sleeve Bedienungsanleitung

zortrax

zortrax M200 Betriebsanleitung

zortrax

zortrax M300 Merkblatt

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax Z-PLA Pro Montageanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax Inventure Merkblatt

zortrax

zortrax M300 Gebrauchsanweisung

zortrax

zortrax M200 Handbuch

zortrax

zortrax M200 Plus Bedienungsanleitung

zortrax

zortrax Z-PETG Bedienungsanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M Series Gebrauchs- und Pflegehandbuch

zortrax

zortrax M200 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch