Zte MF652 Referenzhandbuch

MF652 High Speed USB Data Modem

MAC Help File

No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any

means, electronic or mechanical, including photocopying and microfilm, without the prior written

permission of ZTE Corporation.

The manual is published by ZTE Corporation. We reserve the right to make modifications on print

errors or update specifications without prior notice.

Edition：1

st edition, May 2011

Contents

1 USB Modem Introduction ........................................................................................................... 1

1.1 Introduction ..................................................................................................................... 1

1.2 Safety Warning and Notices.............................................................................................. 1

1.3 System Requirements....................................................................................................... 1

2 Installation ................................................................................................................................. 2

2.1 Unpacking ........................................................................................................................ 2

2.2 Hardware Installation....................................................................................................... 2

2.3 Install the Software .......................................................................................................... 2

2.4 Running the Application Software ................................................................................... 2

2.5 Disconnect the Modem Card Safely .................................................................................. 2

2.6 Software Removal ............................................................................................................ 2

3 Using the Software Interface ...................................................................................................... 3

3.0 LED Indications.................................................................................................................. 3

3.1 Main Interface ................................................................................................................... 3

3.2 Connecting to the Internet ................................................................................................ 4

3.3 Settings ............................................................................................................................. 4

3.3.1 Security Settings ............................................................................................................ 4

3.3.2 Network Settings............................................................................................................ 4

3.3.3 SMS Settings................................................................................................................... 5

3.3.4 Alert Settings.................................................................................................................. 5

3.3.5 System Settings .............................................................................................................. 5

3.4 Contacts ............................................................................................................................ 5

3.4.1 New Group...................................................................................................................... 5

3.4.2 Searching Records .......................................................................................................... 5

3.4.3 Buttons Description........................................................................................................ 5

3.5 SMS ................................................................................................................................... 6

3.5.1 Reading SMS Messages .................................................................................................. 6

3.5.2 Creating a new message ................................................................................................. 6

3.5.3 SMS Interface Operating Guide ...................................................................................... 6

4 Help............................................................................................................................................ 7

4.1 Troubleshooting Guide..................................................................................................... 7

1 USB Modem Introduction

1.1 Introduction

Thank you for choosing the MF652 USB modem. Please read this manual carefully and keep it for future

reference.

The pictures, symbols and contents in this manual are for reference only. They are correct at the time of

publication but might not be completely identical with your modem. We operate a policy of continuous

development. We reserve the right to update the technical specifications in this document at any time without

prior notice.

The USB modem is a multi-mode 3G high speed modem suitable for GSM, GPRS, WCDMA, EDGE and HSDPA

networks. It uses the USB 2.0 standard interface for easy connection to any laptop or desktop PC or MAC.

Compatible with 2G and 3G mobile networks it connects to wireless data and SMS services to give you high

speed data access wherever you are.

1.2 Safety Warning and Notices

To the owner

Some electronic devices are susceptible to electromagnetic interference. The modem is a transmitting

device and may cause interference to sensitive electronic equipment such as audio systems, vehicle

systems and medical equipment. Please consult the manufacturer of the other device before using the

modem.

Operating of computers with the modem may interfere with medical devices like hearing aids and

pacemakers. Please keep the modem more than 20 centimetres away from such medical devices. Turn the

modem off if necessary. Consult a physician or the manufacturer of the medical device before using the

modem near such devices.

Be aware of the regulations when using the modem at places such as oil warehouses or chemical factories,

where there are explosive gases or explosive products being processed. Turn off your modem as

instructed.

Don’t touch the antenna area unnecessarily whilst connected. This can affect your modem performance

and reduce the signal quality.

Store the modem out of the reach of children. The modem may cause injury or get damaged.

The modem contains sensitive electronic circuitry. Do not expose the modem to any liquids, high

temperatures or shock.

Only use original accessories or accessories that are authorized by the manufacturer. Using unauthorized

accessories may affect your modem’s performance, damage your modem and violate related national

regulations.

Avoid using the modem in areas that emit electromagnetic waves, or in enclosed metallic structures eg

lifts.

The modem is not waterproof. Please keep it dry and store it in a cool, dry place.

Don’t use the modem immediately after a sudden temperature change eg from an air conditioned

environment to high temperature and humidity outside. In such cases there could be condensing moisture

inside the modem which can cause internal damage. Unplug the modem and leave it for 30 minutes

before use.

Always handle the modem with care. Be careful not to drop or bend the modem.

There are no user serviceable parts inside the modem. Unauthorised dismantling or repair of the modem

will void the warranty.

The USB Wireless modem is a transmitting device with similar output power to a mobile phone. It uses an

internal antenna to connect to the mobile network. To get the best performance from your device do not

cover or shield the device in any way as this will lead to increased output power. Always leave a clear space

around the device to allow the transmit and receive signals to propagate. SAR tests have been completed

and comply with the Australian regulatory requirements.

1.3 System Requirements

Operating System：Version 10.4.11 or above

Configuration：CPU PowerPC or Intel

Processor 500MB or above

Memory 512M or above

The performance of the modem may be reduced if the configuration is below the recommended

requirement.

2 Installation

2.1 Unpacking

Check the following articles are in the package: 1 x USB Modem, 1×USB Extension cable, Quick Start

Guide, and warranty card.

2.2 Hardware Installation

1. Inserting the USIM Card into the Modem:

The USIM card is the UMTS Subscriber Interface Module provided by your Service Provider. Before using

the modem make sure the USIM card supports data services.

Insert the USIM card with the metal contacts facing downwards and the beveled corner on the outside

edge . There is a diagram showing the correct orientation printed onto the SIM slot label.

2.3 Install the Software

Insert the modem into a USB port and wait for the CD-ROM Join Air to be detected. Go Computer >

Modem and double click Join Air.

Complete the following steps:

a) Press Continue on the welcome page.

b) Select the destination volume then click Install.

c) Enter your user name and password and click OK to install.

d) Click Close to complete the software installation.

If you have problems with installation please contact your service provider for help or see our website for

more info at zte.com.au/optus

2.4 Running the Application Software

Select Finder > Applications > Join Air to run the software.

2.5 Disconnect the Modem Card Safely

Please close the application first then remove the modem.

2.6 Software Removal

Close the application program before the software uninstalling.

Select Finder > Applications >Uninstall Join Air to uninstall the software.

3 Using the Software Interface

3.0 LED Indications

LED indicator Modem Status

Red Offline. Not registered on the network

Greensolid Registered on the 2G network

Greenblinking Active data transfer on the 2G network

Bluesolid Registered on the 3G network

Blue blinking Active data transfer on the 3G network

3.1 Main Interface

The software interface comprises three parts: Function Buttons, System Information Bar, and User

Information areas.

1. Function Buttons

Use the Function buttons to carry out the corresponding operations:

Connect to the Internet Dial Records

SMS Interface Settings Interface

Contacts Help

2. System Information Bar

Use the System Information Bar to monitor your network and modem status

Shows network signal strength USIM card is roaming

P - Packet-switch connection

C - Circuit Switched connection

Current network service type:

UMTSorGSM

Modem Connected Modem disconnected

USIMcardinserted

USIMcardnotinserted

3. User Area

Shows user records such as connected time and data usage.

3.2 Connecting to the Internet

Once you are connected you can browse web pages and access the Internet through the modem. You

can also receive SMS while surfing on the Internet.

Connect to the Internet

Click the Internet button, then click Connect to proceed.

The card takes a few seconds to verify your connection and then shows ‘Status: Connected …’, .

The data amount, connected time etc are displayed in the main window

You can access the Internet and receive email etc by launching your usual applications eg Browser or

Mail software.

When you are connected the Connect button changes to Disconnect. Click Disconnect to end

your session.

Disconnect from the Internet

Click Disconnect to disconnect from the Internet.

Internet Connection Records

Click Logs to show the internet connection records interface.

3.3 Settings

Click the Settings icon to switch to the settings interface.

Note:

Normally there is no need to change any of these settings as they are pre-configured for your network. If

you change networks or are roaming you may need to modify some settings. Consult your service

provider for more information.

3.3.1 Security Settings

Enable the PIN Code:

You can enable a PIN code using the PIN enable feature. When enabled you need to enter your PIN to

start the modem. The PIN code is stored on the USIM card. Consult your service provider for more

information or if you forget your PIN. Click Revise PIN to modify the number.

3.3.2 Network Settings

1. Operator Selection:

Automatic: The system selects the preferred network automatically depending on the user’s selected

rules and the network status.

Manual: The network can be manually selected by the user.

When Manual is selected click Apply to search for available networks.

2．Preferred Mode:

Automatic: The system chooses the best network connection with priority for 3G Networks

3G Only: The system only connects to 3G Networks

2G Only: The system only connects to 2G (GSM) Networks

3.3.3 SMS Settings

The Message Center number is preset for your operator. You may need to update this if you are

roaming on an overseas network. Contact your network supplier for assistance.

3.3.4 Alert Settings

Use the alert settings to modify the system sounds if required

3.3.5 System Settings

You can configure your modem to auto start and auto connect if required.

3.4 Contacts

Click “Contacts” icon to switch to the Contacts interface. The Contacts information can be saved on the

computer or (U)SIM card.

3.4.1 New Group

You can add new groups on the computer. But you cannot add new groups on the (U)SIM card.

Click and name the new group in the group folder tree. Select the folder group you want to add

or edit information, and input all the information according to the prompt.

3.4.2 Searching Records

You can enter any part of the record characters or phone number you are searching for. The

corresponding records or names are listed, scroll to the record you want to view in detail.

Click to edit the information.

3.4.3 Buttons Description

If any records are selected, you can carry out the following steps:

Delete selected records.

Edit the information of the selected record.

CopyTo Copy the records information between computer and the (U)SIM card.

Send message to the mobile phone numbers in the records.

3.5 SMS

Click “SMS” icon to switch to the SMS interface and it shows the number of the SMS in the InBox, OutBox

and Draft. Click the button , or to enter relative interface.

Save received SMS.

Save sent SMS.

Save SMS edited as a draft before sending or after failure.

3.5.1 Reading SMS Messages

Click button or SMS icon in system information area to read the SMS saved in the InBox. Use

the corresponding buttons to Delete, Reply, Edit, SaveTo, or create New message(s).

3.5.2 Creating a new message

Click button to input the recipient’s number and content.

Input the recipient’s number directly or select it from the phonebook, and then press “SMS” button.

The recipient’s number(s) can be one or more, using “;” to separate.

SMS text can not exceed 800 individual English characters (including English symbols) or 350 Chinese

and English mixed characters.

Click “Send” button to send the message. After sending successfully, the SMS will be saved into OutBox

automatically. If sending fails, failure notification will appear, and the message will be saved in Drafts.

Please note:

The maximum number of characters per SMS is 160. If you send more than 1 SMS you will get charged for

multiple messages.

Sending SMS while browsing the web

If network supports, you can send short messages when surf on the Internet. Click “SMS” icon button,

enter the short message interface and send SMS in normal way.

3.5.3 SMS Interface Operating Guide

Enter any of the InBox / OutBox / Drafts to execute the following functions:

Delete: Delete selected short message(s).

Reply: Reply short message to the sender. (OutBox / Drafts do not include this item)

Edit: Edit short message to the other recipients.

SaveTo: Save the selected SMS from the computer to the (U)SIM or from (U)SIM to the computer.

The system indicates when the USIM/SIM card is full (USIM/SIM cards differs in capacity). New messages

can only be received after the user deletes message(s) on the USIM/SIM card.

4 Help

Click the Help icon to see the help information.

4.1 Troubleshooting Guide

If you have any problems with your modem please check this section. If the problem still exists test on an

alternate PC and contact your service provider. Check for more details and FAQ’s at zte.com.au/optus

Problem Possible Causes Suggested Solution

When the device is plugged

in the CDROM drive does not

appear

Previous traces of installed

programs are preventing the

CDROM detection

If you have previously installed the

Connection Manager make sure it is

fully uninstalled. TIP: You can

download the install pack from our

website at zte.com.au/optus

The user interface doesn’t

start or stays ‘Initializing’ after

the modem is plugged in.

PC configuration is not correct.

(No Autorun)

Start the program manually by going

Start > Program Files or use the

shortcut on the desktop. Check the

drivers, try Safe Mode.

The antenna is at the wrong angle

or position.

Use the extension cable and adjust

the angle and position of the USB

modem.

You have no

network coverage.

Try moving location until you get

good reception. Try the extension

cable.

The modem has no signal.

Is your SIM card active and inserted

correctly.

Check your SIM insertion, account

and PIN number if applied.

Message sent failed.

The SMS centre number isn’t

correct.

Contact your Service Provider. Enter

the correct number in the Message

settings.

You have no

network coverage.

Try moving location until you get

good reception. Try the extender

cable

The APN configuration is wrong Check with your service provider and

set the APN in the configuration

settings.

The manual network selection is

wrong.

Select the correct network for your

service provider. Restore Automatic

mode.

Data connection failed.

You are using the wrong APN. Consult your service provider.

The modem cannot connect

to the internet abroad.

You don’t have roaming enabled

on your plan.

Contact your service provider to

enable roaming.

The MicroSDTM card cannot

be read or is not found.

Re-insert the MicroSDTM card. The

maximum capacity is 32GB. The

card is not formatted correctly.

Try another MicroSDTM card and make

sure the capacity and format is

correct.

2GB is FAT16 format

32GB is FAT32 format

Quick Tips

1. Install and test the modem in another computer

2. Check your SIM is working in another device – eg mobile phone

3. Insert a known working SIM card into your modem

4. Confirm your account is active – contact your service provider

5. If the software installation fails download the current version from zte.com.au/optus

Inhaltsverzeichnis

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung

Aztech

Aztech HW831 Bedienungsanleitung