Zte MG880 Bedienungsanleitung

CDMA2000 1X

Wireless Data erminal

User Manual

This Help is used for Wireless Data Terminal of MG880+.

Welcome to Use Help Document of Data Terminal

Through Help document, you could know about the following contents:

Introduction

Safety Warnings and Precautions

Run the Application

Connect/Disconnect

Connection Records

Voice Call

Call History

Short message

Contacts

Settings

Help

ZAPAK URL Web

Trouble-shooting

No part of this publication may be excerpted, reproduced, translated or utilized in any form or by

any means, electronic or mechanical, including photocopying and microfilm, without the prior

written permission of ZTE Corporation.

ZTE Corporation reserves the right to make modifications on errors or update specifications in this

Help without prior notice

1.Introduction

Thank you for choosing CDMA2000 1X Wireless Data Terminal (hereinafter referred to as Data

Terminal) of ZTE Corporation.

Through a standard USB interface, Data Terminal supports CDMA2000 1X network. In the area

where there is signal, it allows you to go surfing on the Internet, send & receive short messages, and

make & receive phone calls.

The pictures in this help are only used to demonstrate your Data Terminal’s functions, so they are

maybe different from what you see on your Data Terminal. Please refer to your Data Terminal if

they are differences.

2.Safety Warnings and Precautions

zUse the original accessories or those authenticated by the manufacturer. Using any

unauthenticated accessories may affect the data terminal’s performance, violate the

warranty provisions or relevant national regulations about telecom terminals, or even

cause body injury.

zDo not disassemble, modify, frequently pull/plug the antenna, stretch, rotate or bend the

antenna with great force.

zBefore pulling out the data terminal, please use Windows safely removing the hardware

and make sure to exit the application. Do not directly pull out the terminal to avoid the

damage of data terminal or the influence on the normal operation of operating system.

zDo not forcefully plug/pull the data terminal to avoid the damage of connector.

zDo not use your data terminal near weak signal or high-precision electronic devices.

Radio wave interference may cause misoperation of electronic devices or other

problems.

zTurn off your data terminal on airplane where it’s forbidden to use it. The data terminal

may affect the normal operation of electronic devices, therefore please follow the

relevant regulations when using your mobile phone on airplane.

zTurn off your data terminal in hospital where it’s forbidden to use it. The data terminal

may affect the normal operation of medical apparatus, therefore please follow the

relevant regulations when using your mobile phone in hospital.

zPlease do not use the data terminal near flammable or explosive materials, otherwise it

might cause failure or fire.

zKeep your data terminal away from water. This may cause overheating or failure if

water or any other kind of liquid enters your mobile phone. Please do not use your data

terminal near high temperature, damp or dusty place.

zKeep your data terminal away from children to avoid shock, plunge or impact. It may

cause body injury when the data terminal is used as a toy.

3.Run the Application

After the application is installed successfully, the application icon will appear on your desktop.

Double-click this icon or select from Start Programs ZTEMT ZTEMT UI Run the

application to display the user interface.

The icons on the interface are used to access the function, which indicate as below:

Connect ZAPAK Voice Call

Voice Log Short Message Net Connect

Net Log Phone book Setting

Help

Status Bar:

1X indication Call indication

Signal strength indication. The more

bars there are, the stronger signals are. Missed call indication

CDMA network unavailable Unread message

indication

Connection indication Inbox full indication

Sleep indication No R-UIM card

inserted indication

Roaming indication R-UIM card inserted

indication

4.Connect/Disconnect

Connect

Click icon to set the relevant parameters. For details, please refer to 12 “Setting”

for details.

Click to enter the interface.

Click .

After connecting to Internet, the current network information will appear on the interface.

Double-click any place in the display area to view the connection drawing.

Please connect the Data Terminal and PC with USB extension cable under weak signal to

obtain the optimal performance. If necessary, adjust the Data Terminal’s position and the

antenna’s direction.

Disconnect

After connecting to Internet, click .

5.Connection Records

Click icon to view connection records. Connection records save the previous relevant

information including Start at, Duration and Transmit bytes, which will help you know the status

easily.

By switching among “List”, “Monthly” and “Statistic”, you could inquire the records every time, by

month or by time.

Note:

The relevant information contained in connection records are just for user’s reference rather than

the charging basis.

Delete Connection Records

Click button to delete the records you have selected on the interface.

Clear Connection Records

Click button to delete all the records.

6.Voice Call

(If this feature is not supported by your Data Terminal, please skip over this chapter.)

Click to enter voice call interface.

Make a call

Click the digits in the right side of the interface, or input the digits directly from keyboard.

Press button or press “Backspace” to delete the previous input digit; press

button or press “Esc” to clear all the inputs.

Click button in the right side of the interface or press “Enter” to make a call.

Receive a call

When there is an incoming call, your computer will alert and the incoming caller ID will

appear on the interface.

Click button in the right side of the interface or press “Enter” to receive the call.

Press button or press “Esc” to reject the call.

Redial the latest outgoing call

Click button in the right side of the interface.

Call Waiting

During a call, you could select to answer the second incoming call, and then you could switch

between the two incoming calls.

Please firstly apply for this service from your local telecom operator.

During a call, if there is a new incoming call, a pop-up window will prompt you that you

have the second incoming call.

If you select to answer, please click “Accept waiting call” button. The previous call won’t

be ended, but temporarily paused.

You could switch between two incoming calls by clicking “Switch call”.

Three-way Call

This function allows for the call among three parties. Please firstly apply for this service from your

local telecom operator.

Note:

You need set “Show 3 way call button during calling”. Please perform the setting according to

“Setting”.

You could click “Dial second call” button during a call, input the third-partynumber in the

pop-up window, and then press “OK” button to call the third party. In this case, the original

call won’t be ended, but temporarily paused.

If the third party answers the call, click “Start conference” to enter the conference call.

During three-way conference call, click “Hangup second call” button to end the

conference call, and return to the original call.

7.Call History

(If this feature is not supported by your Data Terminal, please skip over this chapter.)

Click icon to view the call history. The outgoing/incoming calls are saved in call history,

including missed calls, incoming calls, outgoing calls, and talk duration. You could select the type

you want to view.

Missed/Received/Dialed Calls

Click button to delete your selected record.

Click button to delete all records in Missed/ Received/Dialed catalog.

Click button to dial the number.

Click button to send a short message to this number.

Click button to save this number to the phone book.

Data Log

Click button to clear the talk duration.

8.Short Message

(If this feature is not supported by your Data Terminal, please skip over this chapter.)

Click icon to enter Short message interface.

Send a Message

Input the text and the recipient’s number..

Input the recipient’s number or click button to select the recipient from phone book.

Add more recipients if you like.

Select priority.

Click button to send a message.

Click button to save the text into Draftbox.

The received messages will be saved in the Data Terminal In-box.

You could copy the messages from the Data Terminal In-box to PC In-box by selecting Copy or

Copy All; you could also copy the messages from PC In-box to the Data Terminal In-box by

selecting Copy.

Take Data Terminal In-box as an example:

Click to reply to the sender.

Forward

Click to forward this message to other recipients.

Dial Sender’s Number

Click to dial the sender’s phone number.

Save Sender’s Number

Click to save the sender’s number into phone book.

Delete

Click to delete your selected records.

Clear

Click to delete all the records in the inbox..

Copy

Click to copy your selected record into PC.

Copy All

Click to copy all the records from the data terminal to PC.

9.Contacts

(If this feature is not supported by your Data Terminal, please skip over this chapter.)

Click to view the Contacts. You could select to save the contacts in the PC,Modem (Data

Terminal) Emergent.

Take “Save the call history in PC” for example in the following:

Add

Click then input the contents and select “OK” to add a new contact.

Edit

Click then edit the contents and select “OK” to edit the contact information.

Search for contacts

Click to search for the contacts by name or number.

Delete

Click to delete your selected contact.

Delete All

Click to delete all the contacts.

Send messages from the Contacts

Click to compose the text. You could send the message to multiple recipients.

Dial from the Contacts

Click to dial your selected phone number.

Copy

Click to copy your selected contacts to other storage location.

Copy All

Click to copy all contacts to other storage location.

Import the call history.

Click to import the Contacts (*.txt format) in PC to the terminal.

Export the call history.

Click to export the Contacts (*.txt format) in the terminal to PC.

10. Settings

Click to enter the settings interface.

Network Connection Settings

Set up the relevant parameters on the “Network” interface.

After the settings, click “Apply” button to save the settings on the current interface.

Click “Default” button and then “Apply” button to restore the settings on the current

interface to factory default..

Note:

The default network setup parameters are as below. Different regions may have different network

setup parameters, so please consult your local telecom operator.

Phone: #777

User: card

Password: card

If your Data Terminal does not support some following functions, please neglect relevant

description.

Other Settings:

Click “Options” to switch the interface, and you could set URL, etc. If you want to use

conference call, please select “Show 3 way call button during calling”;

After the setting, click “Apply” button to save the settings on the current interface.

Click “Change Password” button to set lock device. The password is required when you

start the application. The setting has nothing to do with "Default" button.

Click “Default” button and then “Apply” button to restore the settings on the current

interface to factory default.

Select ring tone

After clicking “Ring”, you could set different ring tones for Unconditional forwarding,

No answer forwarding, Busy forwarding and Call waiting.

After the settings, click “Apply” button to save the settings on the current interface.

Andere Handbücher für MG880

Inhaltsverzeichnis

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung

Aztech

Aztech HW831 Bedienungsanleitung