Zte MF60 Bedienungsanleitung
TABLE OF CONTENTS
Introducon
Cauon for iPhone & Smartphone Users
Connecng to the Internet
Troubleshoong
Frequently Asked Quesons
Customer Support
1
2
3
4
6
7
7
8
11
14
16
17
About the device
Screen indicators
If hotspot displays ‘insert SIM’ and/or will not charge or power on
If hotspot displays ‘limited service’ and/or has no signal strength
If hotspot displays ‘disconnected’ and/or will not connect over Wi-Fi
If hotspot does not prompt you for a password and/or connect aer reset
Indicators and Their Meaning
Network Type
“3G” (High Speed), HSPA+/ WCDMA
“E” (Mid Speed), EDGE
“2G”(Low Speed), GPRS/GSM
Signal Strength
5 bars is best. If there is no signal, only the antenna
shows.
Baery Life Remaining
4 bars is a full charge.
Flashes when charging.
Carrier Name
Try reseng the device when you see “Limited service”
(See page 8)
Connecon Status
Try troubleshoong the device when you see
“Disconnected” (See page 11)
Auto/Manual Connect
“A” indicates it will automacally connect to a
network when receiving a signal.
“M” indicates that you must manually connect to a
network. (See page 8)
Number of Wi-Fi Devices Connected
Indicates number of devices connected to the mobile
hotspot. When “0” is shown, your device (computer,
tablet, smartphone, etc.) is not connected to the
hotspot via Wi-Fi.
3
3G
AT&T
Connected
M
A
1
Network Type
Signal Strength
Baery Life Remaining
Carrier Name
Connecon Status
Auto/Manual Connect
Number of Wi-Fi
Devices Connected
※CAUTION※ iPhone and Smartphone Users
Please be sure to turn OFF data roaming on WiFi-enabled mobile phones. Failure to
do so may result in internaonal roaming charges incurred with your local carrier.
How to turn off data roaming on iPhone (iOS 7)
How to turn OFF data roaming on Android Smartphone
1. From the home screen, select Sengs ⇒ Select Cellular ⇒ Select Roaming
2. Ensure the Voice & Data Roaming switch is disabled.
⇒ Enabled when the switch is in the green posion.
“Sengs“⇒ “Wireless and network“⇒ “Mobile networks“⇒ “Data roaming“
Please ensure that Data roaming is UNCHECKED.
Note: Please check your phone manufacturer's guide for instrucons on how to turn off data roaming
4
Please Turn OFF iCloud & Automac Downloads (iOS7)
1. “Sengs“→ “iCloud“
→ “Storage and Backup“
2. “Sengs“→ “iCloud“ → Turn OFF
“Photo Stream“ and “Documents & Data“.
If iCloud is turned on and connected to the internet, it will send
and receive data automacally, which could result in exceeding
the limits of a carrier’s fair usage policy. (See page 16)
Please be sure to also disable
Automac Downloads.
Tap Sengs > iTunes & App Stores
on your device.
Tap Sign In if you're not already
signed in to the iTunes Store.
Enter your Apple ID and password.
Tap to disable Automac
Downloads for each content type.
5
1.
2.
3.
4.
Press and hold the power buon for 5 seconds. Your mobile hotspot
starts up and is ready for you to connect another device to it (such as
your computer, tablet or smartphone).
Follow these instrucons to connect up to ten Wi-Fi enabled devices
to the Internet using your XCom Global ZTE Mobile Hotspot.
How To Connect To The Internet
SSID：※※※※※※※※※※
PW: ※※※※※※※※
Connect your computer or other device to your mobile hotspot
2
Check the browser icon on the mobile hotspot to ensure at least
one device is connected. Launch your browser and access the
Internet.
3
6
※ The password is case-sensive. Please type it carefully.
0=#zero, O=alphabet, 5=#five, S=alphabet,
8=#eight, B=alphabet I=alphabet “eye”, 1=#one,
l=Small “el”, L=Capital “el”
Guide to leers/numbers on the password label:
a. On your computer, view the list of available Wi-Fi networks.
b. Select the Wi-Fi SSID (Network Name) displayed on the label
underneath the mobile hotspot LCD screen, and connect to it.
c. When prompted, enter your Wi-Fi password as it appears on the
label underneath the mobile hotspot LCD screen --or -- it is printed
inside the baery compartment of your mobile hotspot.
1
Hotspot Displays 'Insert SIM', And/Or Will Not Charge Or Power On
- When the mobile hotspot does not power on
- When the mobile hotspot displays “Insert SIM”
- When the mobile hotspot does not indicate that the baery is charging
⇒ Remove the SIM card, wipe off the metal contacts with clean cloth,
and reinstall it.
Li up the baery cover from the boom of the mobile hotspot,
then remove the baery.
Remove the SIM card by sliding in the direcon of the arrow
Wipe off the metal contacts with so clean cloth
Insert the SIM card and baery with the contacts located against
the metal springs and press the baery down in the case. Line the
baery cover up correctly and press gently to close the case.
7
Troubleshoong
1) Type “192.168.0.1” into the address bar of your web browser.
2) Type “admin” to login to the administraon page. The entry field is
located on the right side of the screen.
⇒Use Manual Search to enable your hotspot to manually search for a
cellular carrier network signal.
Click “Sengs” on the menu bar.
Access the mobile hotspot configuraon page from a device that is
acvely connected to the hotspot.
Hotspot Displays 'Limited Service' And/Or Has No Signal Strength
- When the mobile hotspot has no signal.
- When the hotspot displays "limited service".
8
Troubleshoong
Andere Handbücher für MF60
7
Inhaltsverzeichnis
Andere Zte WLAN-Router Handbücher
Zte
Zte MF93D Bedienungsanleitung
Zte
Zte Z289L Bedienungsanleitung
Zte
Zte MF23 Bedienungsanleitung
Zte
Zte 203Z Montageanleitung
Zte
Zte MF612 Bedienungsanleitung
Zte
Zte MF910 Bedienungsanleitung
Zte
Zte MF65 Bedienungsanleitung
Zte
Zte MF275U Bedienungsanleitung
Zte
Zte MF93D Bedienungsanleitung
Zte
Zte Telstra MF90 Bedienungsanleitung
Zte
Zte AC30 Bedienungsanleitung
Zte
Zte R226 Bedienungsanleitung
Zte
Zte MF60 Bedienungsanleitung
Zte
Zte MF269 Bedienungsanleitung
Zte
Zte MU5001 Bedienungsanleitung
Zte
Zte MF971V Bedienungsanleitung
Zte
Zte MF283U Bedienungsanleitung
Zte
Zte ZXV10 W300 Technische Daten
Zte
Zte MF51 Bedienungsanleitung
Zte
Zte MF985U Bedienungsanleitung
