ZyXEL Communications ZyWALL USG 100 Series Bedienungsanleitung

ZyWALL USG 100/200 Series

Unified Security Gateway

Quick Start Guide

Version 2.10

3/2008

Edition 1

DEFAULT LOGIN

LAN Port P4

LAN IP Address http://192.168.1.1

User Name admin

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 9

ESPAÑOL 16

FRANÇAIS 23

ITALIANO 30

РУССКИЙ 37

简体中文 45

繁體中文 52

ENGLISH

1 Checking the Package Contents

2 Rack-mounted Installation

Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.

Note: Leave 10 cm of clearance at the sides and 20 cm in the rear.

1Align one bracket with the holes on one side of the ZyWALL and secure it with the included bracket

screws. Similarly, attach the other bracket.

2After attaching both mounting brackets, position the ZyWALL in the rack by lining up the holes in the

brackets with the appropriate holes on the rack. Secure the ZyWALL to the rack with the rack-mounting

screws.

Your package should

include one of each

of the following:

• ZyWALL

•Powercord

• Rack-mounting kit

• RJ-45 Ethernet cable

• RS-232 console Y-cable

• Printed Quick Start Guide

• Compact disk (CD)

ENGLISH

3 Connecting the Hardware

1It is recommended that you configure the ZyWALL before using it to protect your network. Use an Ethernet

cable to connect a computer to port P4.

2Use another Ethernet cable(s) to connect port 2 and/or port 3to an Ethernet jack with Internet access.

3Use the included power adaptor to connect the power socket (on the rear panel) to a power outlet.

4Look at the front panel. The PWR light turns on. The SYS light blinks during system testing and

initialization and then stays on when the system is ready.

4 Web Login

1Launch your web browser and go to http://192.168.1.1 (the

ZyWALL automatically redirects you to https://192.168.1.1).

ENGLISH

2Click Yes to proceed if you get a security alert or

certificate screen.

3Enter admin as the user name and 1234 as

the password. Click Login.

4It is strongly recommended that you change the

password. Type and retype a new password, and click

Apply.

ENGLISH

5 Installation Setup Wizard

Use an installation setup wizard to connect to the Internet and register the ZyWALL and/or activate trial

services, like IDP and content filter.

Note: Use the installation wizard only for initial configuration starting from the default configuration.

Changes you make in the installation wizard may not be applied if you have already changed the

ZyWALL’s configuration.

The Status screen

opens. Click the Wizard

icon in the upper

right corner.

•INSTALLATION SETUP, ONE ISP sets up a sin-

gle Internet connection for wan1.

•INSTALLATION SETUP, TWO ISP sets up Inter-

net connections for wan1 and wan2.

The wizard screens vary depending on the encapsulation

type you use. Refer to information provided by your ISP

and the web help screens to know what to enter in each

field. You can leave fields blank if you don’t have that

information.

ENGLISH

6 Default Settings and Port Details

The ZyWALL is configured for the following network topology by default. (ZyWALL USG 200)

ZyWALL USG 200

Port Interface Zone IP Address and DHCP Settings Suggested Use With Default Settings

P1, P2 wan1,

wan2

WAN DHCP clients Connections to the Internet

P3 opt OPT None, DHCP server disabled Third WAN, additional LAN, WLAN, or

DMZ port or a separate network.

P4, P5 lan1 LAN1 192.168.1.1, DHCP server enabled Protected LAN

P6 ext-wlan WLAN 10.59.0.1, DHCP server enabled Wireless access points

P7 dmz DMZ 192.168.3.1, DHCP server disabled Public servers (such as web, e-mail and

FTP)

AUX aux None None Auxiliary modem

CONSOLE n/a None None Local management

ENGLISH

ZyWALL USG 100

7 Troubleshooting

Port Interface Zone IP Address and DHCP Settings Suggested Use With Default Settings

P1, P2 wan1,

wan2

WAN DHCP clients Connections to the Internet

P3, P4, P5 lan1 LAN1 192.168.1.1, DHCP server enabled Protected LAN.

P6 ext-wlan WLAN 10.59.0.1, DHCP server enabled Wireless access points

P7 dmz DMZ 192.168.3.1, DHCP server enabled Public servers (such as web, e-mail and

FTP)

AUX aux None None Auxiliary modem

CONSOLE n/a None None Local management

Label Type Description

USB USB Connect a (USB) 3G wireless card to access the Internet through a 3G network. At

the time of writing, you can use the Huawei E220.

P1~P7 RJ-45 Use 8-wire Category 5e or above Ethernet cables to connect routers, switches,

computers, routers, access points, and so on.

AUX RS-232 Use an RS-232 console cable to connect dial backup/dial-in modem.

CONSOLE RS-232 Use an RS-232 console cable to connect a local computer for command-based

management.

EXTENSION

CARD SLOT

PCMCIA Insert a wireless LAN card to use the wireless LAN feature. At the time of writing, you

can use ZyXEL’s G-170S wireless card. You can optionally insert a 3G wireless card to

access the Internet wirelessly via a 3G network. At the time of writing, you can use a

Sierra Wireless AC850 or AC860 3G wireless card.

Problem Corrective Action

None of the LEDs

turn on.

Make sure that you have the power cord connected to the ZyWALL and plugged in to an

appropriate power source. Make sure you have the ZyWALL turned on. Check all cable

connections.

If the LEDs still do not turn on, you may have a hardware problem. In this case, you should

contact your local vendor.

ENGLISH

8 Procedure to View a Product’s Certification(s)

1Go to www.zyxel.com.

2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3Select the certification you wish to view from this page.

Cannot access

the ZyWALL from

the LAN.

Check the cable connection between the ZyWALL and your computer or switch. Refer to

section 3 for details.

Ping the ZyWALL from a LAN computer. Make sure your computer’s Ethernet card is

installed and functioning properly. Also make sure that its IP address is in the same subnet as

the ZyWALL’s.

In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In

the Command Prompt window, type "ping" followed by the ZyWALL’s LAN IP address

(192.168.1.1 is the default) and then press [ENTER]. The ZyWALL should reply.

If you’ve forgotten the ZyWALL’s password, use the RESET button. Press the button in for

about 5 seconds (or until the PWR LED starts to blink), then release it. It returns the ZyWALL

to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.; see your User’s

Guide for details).

If you’ve forgotten the ZyWALL’s IP address, you can use the commands through the

console port to check it. Connect your computer to the CONSOLE port using a console

cable. Your computer should have a terminal emulation communications program (such as

HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow

control and 115200 bps port speed.

Cannot access

the Internet.

Check the ZyWALL’s connection to the Ethernet jack with Internet access. Make sure the

Internet gateway device (such as a DSL modem) is working properly.

Check the WAN port’s status in the Status screen. Use the installation setup wizard again

and make sure that you enter the correct settings.

Problem Corrective Action

DEUTSCH

1 Prüfen des Packungsinhalts

2 Rackmontage

Montieren Sie die ZyWALL in einem 19"-Rack oder stellen Sie es auf eine stabile Unterlage.

Hinweis: Lassen Sie seitlich 10 cm und hinten 20 cm Platz.

1Richten Sie eine Halterung an den Löchern an der Seite der ZyWALL aus und schrauben Sie sie mit den

mitgelieferten Montageschrauben fest. Verfahren Sie ebenso mit der zweiten Halterung.

2Wenn Sie beide Montagehalterungen befestigt haben, richten Sie die ZyWALL so im Rack aus, dass die

entsprechenden Schraublöcher übereinander stehen. Befestigen Sie die ZyWALL mit den

Befestigungsschrauben am Rack.

Prüfen Sie ob alle

Teile vorhanden

sind:

• ZyWALL

• Netzkabel

• Rackmontage-Zubehör

• RJ-45-Ethernetkabel

• Y-Kabel für RS-232-Konsole

• Kurzanleitung in Druckform

•CD

DEUTSCH

3 Anschließen der Hardware

1Es wird empfohlen, die ZyWALL zu konfigurieren, bevor Sie diese in Ihrem Netzwerk einsetzen. Schließen

Sie einen Computer mit einem Ethernetkabel an Port P4 an.

2Schließen Sie an Port 2 und/oder Port 3Ihren Router mit Internetzugriff an.

3Schließen Sie den mitgelieferten Netzadapter an den Netzanschluss (an der Rückseite des Geräts) und an

eine Netzsteckdose an.

4Betrachten Sie das vordere Bedienfeld. Die PWR-LED beginnt zu leuchten. Die SYS-LED blinkt während

des Systemtests und der Initialisierung, und sie leuchtet, wenn der Test abgeschlossen und das System

bereit ist.

4 Anmelden im Internet

1Starten Sie Ihren Internetbrowser und rufen Sie die Seite

http://192.168.1.1 auf (der ZyWALL leitet Sie automatisch

zur Seite https://192.168.1.1 weiter).

Andere Handbücher für ZyWALL USG 100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications P-662H-61 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1435-B101 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL USG 100 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications G-4100 v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-793H 601156 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 70 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyAIR G-4100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3301 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ADSL2+ 4-port Gateway P-660H-D Series Handbuch

ZyXEL Communications

ZyXEL Communications P-324 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-662HW-D - V3.40 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-870H-53A v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG2100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1435-B101 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW Series Montageanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-T - V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL USG-1000 Handbuch

ZyXEL Communications

ZyXEL Communications MAX-200M1 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312-T20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG9827-B50A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications p-2302r series Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt