ZyXEL Communications P-660W-Tx v2 Bedienungsanleitung

P-660W-Tx v2

ADSL Router over POTS/ISDN

Quick Start Guide

Version 3.40

03/2008

Edition 1

DEFAULT LOGIN

IP Address http://192.168.1.1

Password 1234

P-660W-Tx v2 Quick Start Guide

Overview

The P-660W-Tx v2 lets you:

• Set up a wireless network with IEEE 802.1b and IEEE 802.1g capability

• Set up a DSL connection to the Internet without the need for a modem

• Set up advanced router features, including a firewall and wireless security.

Follow these steps to set up a DSL connection to the Internet and a wireless network using

the P-660W-Tx v2.

1Set Up Your Hardware, page 2

2Configure the P-660W-Tx v2 for Internet Access, page 3

3Set Up a Wireless Network, page 9

See the User’s Guide on the included CD for details on all of the P-660W-Tx v2’s features.

Insert the CD into your CD-ROM, if a screen does not pop-up, use Windows Explorer (My

Computer) to go to the CD-ROM (commonly drive D) and browse for the User’s Guide.

Internet

P-660W-Tx v2 Quick Start Guide

1 Set Up Your Hardware

1 Antenna: Point the antenna upwards (perpendicular to the ground).

2DSL: Connect the P-660W-Tx v2 to a telephone jack using a telephone wire.

3ETHERNET: Use an Ethernet cable to connect the Ethernet port on your computer to

the Ethernet port on the P-660W-Tx v2.

4POWER: Use the included power adaptor to connect the POWER socket to an

appropriate power source (see the User’s Guide for power adaptors specifications by

region).

5ON/OFF: Push the power switch to the ON position to turn on the P-660W-Tx v2.

DSL

ETHERNET

POWER

ON/OFF

RESET

P-660W-Tx v2 Quick Start Guide

Look at the LEDs (lights)

The DSL light blinks and then stays on when a DSL connection is detected. The

ETHERNET light turns on if your computer is properly connected to the P-660W-Tx v2

using the Ethernet cable. When you connect the power, the POWER light blinks and stays

on once the device is ready.

VCheck your connections if the POWER or ETHERNET light does not turn on. If

this doesn’t help, disconnect the P-660W-Tx v2 from its power source, wait for

a few seconds and turn it back on.

2 Configure the P-660W-Tx v2 for Internet Access

You may configure the P-660W-Tx v2 for Internet access in one of these ways:

• Use Zero Configuration to set up your Internet connection automatically in section 2.1.

• If Zero Configuration does not detect your Internet access settings, use the Connection

Wizard to configure Internet access settings in section 2.2.

2.1 Set up Internet Access with Zero Configuration

Launch your web browser and navigate to any website (for example, www.zyxel.com). The

P-660W-Tx v2 automatically detects and configures your Internet connection. This may

take about two minutes.

If you have a PPPoE or PPPoA

connection, a screen displays

prompting you to enter your

Internet account information.

Enter the user name, password

and/or service name exactly as

provided. Click Apply.

P-660W-Tx v2 Quick Start Guide

2.2 Set up Internet Access with the Connection Wizard

If Zero Configuration does not detect your Internet access settings, use the Connection

Wizard to set up Internet Access. Access the P-660W-Tx v2’s web configurator so you can

use the Wizard. (The web configurator is the P-660W-Tx v2’s software interface that lets

you configure settings on the P-660W-Tx v2.)

2.2.1 Access the Connection Wizard

1Launch a web browser such as Internet Explorer.

Enter http://192.168.1.1 and press [ENTER].

2The Password window displays. Enter the

password (1234 is the default) and click Login.

VIf the login screen does not display, check your cable connections. If that

doesn’t help, check your web browser’s security settings. See the appendix

in the User’s Guide for more suggestions. If you’ve forgotten the password,

see the User’s Guide for instructions on using the RESET button.

3Change the password and click Apply.

4In the Site Map

screen, click

Connection

Setup.

P-660W-Tx v2 Quick Start Guide

2.2.2 Configure Internet Access and Local Network Settings with the

Connection Wizard

Use the Connection Wizard to set up access to the Internet through your ISP. These are

your WAN (wide area network) settings. Then use the Connection Wizard to set up the

connection from your computer to the P-660W-Tx v2. These are your LAN (local area

network) settings.

"Enter the Internet access information given to you by your ISP exactly in

each wizard screen. Follow the instructions in this guide or leave the field

blank or at its default setting. Click Next to continue or click Back to return

to the previous screen. Screen information is not saved when you click

Back. If your connection times out, log back in and restart the Wizard.

1From the Mode drop-down list box, select

Routing if your P-660W-Tx v2 is a gateway

between the Internet and your local network and

you need routing features such as NAT (Network

Address Translation) or a firewall. Select Bridge

if your P-660W-Tx v2 is on a private network

behind a router, and you do not need routing

features such as NAT or a firewall.

2Configure your Encapsulation, Multiplex and

other settings based on the settings your ISP

provides you.

Bridge

• If you selected Bridge and RFC 1483 in the previous screen, go to step 3in this section.

• If you selected Bridge in step 1of this sec-

tion and PPPoA, the following screen

appears. Type your User Name and Pass-

word. Select Nailed-Up Connection to set

a permanent connection which automatically

reconnects on disconnection. Select Con-

nect on Demand to allow connection only

when required and with an idle time-out

period (in seconds) in the Max. Idle Timeout

field. Click Next.

P-660W-Tx v2 Quick Start Guide

3Check your WAN and LAN settings in the

screen that appears. Click Save Settings.

Go to step 9of this section.

Routing

• If you selected Routing in step 1of this section, one of the following four screens appears

depending on the Encapsulation you chose in step 1of this section.

•PPPoA, PPPoE: Type your User

Name and Password.

•PPPoE, PPPoA, ENET: Select

Obtain an IP Address Automati-

cally if your ISP (Internet Service

Provider) assigns IP addresses

automatically. Otherwise, select

Static IP Address if your ISP has

assigned you an IP address.

Check with your ISP if you are

unsure of which setting to choose.

•PPPoA, PPPoE: Select Nailed-Up

Connection to set a permanent

connection which automatically

reconnects on disconnection.

Select Connect on Demand to

allow connection only when

required and with an idle time-out

period (in seconds) in the Max.

Idle Timeout field.

•PPPoE, PPPoA, ENET, RFC 1483:Select SUA Only for shared Internet access with a sin-

gle ISP. This is recommended. Otherwise, select None if accessing the Internet on a public

IP address, or select Full Feature for advanced NAT features. See your User’s Guide for

more details.

4Click Next.

PPPoE

PPPoA

RFC 1483

ENET

P-660W-Tx v2 Quick Start Guide

5Check your WAN and LAN settings in the screen that

appears. Click Change LAN Configuration to configure

the P-660W-Tx v2 for your local area network (LAN) and

go to step 6of this section.

• Otherwise click Save Settings and go to step 9of this sec-

tion.

6If you clicked Change LAN Configuration,

the following screen appears.

• Type the IP address and subnet mask for the P-

660W-Tx v2 on your LAN.

• Disable the DHCP Server if another device on

your LAN, such as a router, already allocates IP

addresses, or devices on your LAN have static

IP addresses. Go to step 8of this section.

Otherwise, if the P-660W-Tx v2 is to allocate IP

addresses on your LAN, enable the DHCP

Server. Computers on your LAN will then need

to be set to receive an IP address automatically.

See the User’s Guide for more information on

configuring this.

7If you enable the DHCP Server, ensure the Client IP Pool Starting Address is on the

same domain as your LAN IP Address (that is, the first three parts of the IP addresses

are the same). If you were given DNS Server settings, type them here. Otherwise leave

the default settings.

8Click Finish to save your settings and go to step 9of this section. Otherwise, click Back

to check your settings as in step 5of this section.

"If you change the P-660W-Tx v2’s LAN IP address, you must use the new

IP address if you want to access the web configurator again.

P-660W-Tx v2 Quick Start Guide

9The P-660W-Tx v2 automatically tests

the connection to the computer(s)

connected to the LAN port. To test the

connection from the P-660W-Tx v2 to the

ISP, click Start Diagnose. Otherwise

click Return to Main Menu to go back to

the main screen.

VIf the P-660W-Tx v2 cannot connect to the Internet, check the Internet

connection settings in the wizard. Make sure you entered the correct user

name and password if you are using PPPoE or PPPoA.

10 Congratulations. Open a web browser, such as Internet Explorer, to visit your favorite

website.

3 Set up a Wireless Network

Follow these steps to set up a wireless network.

3.1 Configure Wireless Settings on Your P-660W-Tx v2

1Click the Wireless LAN

link under Advanced

Setup.

P-660W-Tx v2 Quick Start Guide

2Click Wireless.

3Select Enable Wireless LAN.

4 ESSID: Type the name (up to 32

characters) you want to give to your

wireless network.

5ChannelID: Change the Channel ID

from the default if interference is a

problem on your network.

6 Security Mode: Select the strongest

Security Mode that devices on your

wireless network support. WPA2-PSK

is a good choice for a home network. In

this screen, select WPA Compatible

and type a Pre-Shared Key using a

combination of letters and numbers

(8~63 characters long). Then click

Apply to save your settings.

"Write down the Pre-Shared Key and ESSID as you will need to use them

again when you connect your computer to the P-660W-Tx v2.

3.2 Connect to the P-660W-Tx v2 Wirelessly From Your Computer

You can now connect to your P-660W-Tx v2 via a wireless connection, and access the

Internet. You need the ESSID and also the Pre-Shared Key if you set up security in the

previous section. The connection procedure is shown here (using Windows XP as an

example).

1Right-click the wireless adapter icon which appears in

the bottom right of your computer screen. Click View

Available Wireless Networks.

Write down the Pre-Shared Key!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications ES-105/ES-108 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-417N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2802HW-I Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660RU-Tx Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications A-6000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PRESTIGE 153 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660RU-Tx v3 SERIES Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 100L Gebrauchsanweisung

ZyXEL Communications

ZyXEL Communications ES-2024A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 652 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-335U Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XMG3512-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3311 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 623 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 660H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 2602HW-C Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications MAX-306 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R-F1 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8825-T50 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312-B10D Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications BG-418N v1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XS3700 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung