ZyXEL Communications ES-105/ES-108 Bedienungsanleitung

ES-105/ES-108

Ethernet Switch

User’s Guide

December 2002

Interference Statements and Warnings

FCC Interference Statement

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operations.

FCC Warning

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the

interference at his own expense.

CE Mark Warning

This is a class A product. In a domestic environment this product

may cause radio interference in which case the user may be required

to take adequate measures.

Taiwanese BCIQ A Warning

Certifications

Refer to the product page at www.zyxel.com.

ZyXEL Limited Warranty

ZyXEL warrants to the original end user (purchaser) that this product

is free from any defects in materials or workmanship for a period of

up to two (2) years from the date of purchase. During the warranty

period and upon proof of purchase, should the product have

indications of failure due to faulty workmanship and/or materials,

ZyXEL will, at its discretion, repair or replace the defective products

or components without charge for either parts or labor and to

whatever extent it shall deem necessary to restore the product or

components to proper operating condition. Any replacement will

consist of a new or re-manufactured functionally equivalent product

of equal value, and will be solely at the discretion of ZyXEL. This

warranty shall not apply if the product is modified, misused,

tampered with, damaged by an act of God, or subjected to abnormal

working conditions.

Note

Repair or replacement, as provided under this warranty, is the

exclusive remedy of the purchaser. This warranty is in lieu of all

other warranties, express or implied, including any implied warranty

of merchantability or fitness for a particular use or purpose. ZyXEL

shall in no event be held liable for indirect or consequential damages

of any kind of character to the purchaser.

To obtain the services of this warranty, contact ZyXEL's Service

Center for your Return Material Authorization number (RMA).

Products must be returned Postage Prepaid. It is recommended that

the unit be insured when shipped. Any returned products without

proof of purchase or those with an out-dated warranty will be

repaired or replaced (at the discretion of ZyXEL) and the customer

will be billed for parts and labor. All repaired or replaced products

will be shipped by ZyXEL to the corresponding return address,

Postage Paid. This warranty gives you specific legal rights, and you

may also have other rights that vary from country to country.

Getting to Know Your Switch

Introduction

The switch is a multi-port switch that can be used to build high-

performance switched networks. The switch is a store-and-forward

device that offers low latency for high-speed networking. The switch

is designed for SOHO (Small Office Home Office) businesses.

Standalone Workgroup Application

The switch can be used as a standalone switch to which computers,

servers and print server are directly connected to form a small

workgroup.

Figure 1 Standalone Workgroup Example using the ES-108

Hardware Description and Installation

The switch is suitable for an office environment where it can be

placed on a desktop.

Desktop Installation

Step 1. Make sure the switch is clean and dry.

Step 2. Set the switch on a smooth, leveled and sturdy flat space

strong enough to support the weight of the switch and the

connected cables. Make sure there is a power outlet

nearby.

Step 3. Make sure there is enough clearance around the switch to

allow air circulation and the attachment of cables and the

power cord.

Do not block the ventilation holes. Leave

space between switches when stacking.

Rear Panel Connection

The RJ-45 ports and the power port are located on the rear panel of

the switch.

Figure 2 Rear Panel of the ES-105

Figure 3 Rear Panel of the ES-108

RJ-45 Auto-negotiating Ports

Your switch comes with 5 or 8 10Base-T/100Base-TX RJ-45 ports

depending on the model of your switch. The auto-negotiation feature

allows the switch to detect the speed of incoming transmission and

adjust appropriately without manual intervention. It allows data

transfers of either 10 Mbps or 100 Mbps in either half-duplex or full-

duplex mode depending on your Ethernet network.

Auto-sensing MDI/MDIX ports

Each 10Base-T/100Base-TX RJ-45 MDI/MDIX port allows you to

connect to a computer or to a hub using either a straight-through or a

crossover Ethernet cable.

Rear Panel Ethernet Cable Connections

Use unshielded twisted pair (UTP) or shielded twisted-pair (STP)

Ethernet cables for RJ-45 ports. The following table describes the

types of network cable used for the different connection speeds.

Table 1 Network Cable Types

SPEED NETWORK CABLE TYPE

10 Base-T 100Ω2-pair UTP/STP Category 3, 4 or 5

100 Base-TX 100Ω2-pair UTP/STP Category 5

Make sure the cable length between

connections does not exceed 100 meters (328

feet).

Power Port

Use the supplied power adapter to connect your switch to a power

source. Refer to the label on the power adapter for more information.

Front Panel LEDs

The LED indicators give real-time information about the status of the

switch.

Figure 4 The Front Panel LEDs of the ES-105

Figure 5 The Front Panel LEDs of the ES-108

The following table provides descriptions of the LEDs.

Table 2 The Front Panel LED Descriptions

LED COLOR STATUS DESCRIPTION

PWR Green On The switch is on and receiving power.

Off The switch is not receiving power.

LK/ACT Green On The port is connected to an Ethernet network.

Off The port is not connected to an Ethernet

network.

Blinking The port is receiving or transmitting data.

Orange On The port is operating in full-duplex mode.

Blinking Packet collision occurred on this port.

FD/COL

Off The port is operating in half-duplex mode or

no Ethernet device is connected to this port.

Troubleshooting

Troubleshoot the switch using the LEDs to detect problems.

Power LED

The PWR LED on the front panel does not light up.

Table 3 Troubleshooting Power LED

STEPS CORRECTIVE ACTION

1 Check the connections from your switch to the power source.

Make sure you are using the supplied power adapter and that

you are using an appropriate power source.

2 Make sure the power source is turned on and that the switch is

receiving sufficient power.

3 If these steps fail to correct the problem, contact your local

distributor for assistance.

LK/ACT LED

The LK/ACT LED does not light up when a device is connected.

Table 4 Troubleshooting LK/ACT LED

STEPS CORRECTIVE ACTION

1 Verify that the attached device(s) is turned on and properly

connected to your switch.

2 Make sure the Network Interface Cards (NICs) are working on

the attached devices.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications GS2210 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 971M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 202H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 2602R Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2024A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 128IMH Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3311 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ALC-1024L Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG6816 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2802HW(L)-IX Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-202H Plus v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2812HNU-51c Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NR/FWA Outdoor Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications o2 HomeBox 6641 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-108S Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-335U Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 641 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PMG5317-T20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG6604 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NXC2500 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-662HW-D - V3.40 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL VPN2S Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P650HW Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 128IMH Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise