3Com 3CWE820A Bedienungsanleitung

Ethernet Client Bridge

3CWE820A

Wireless Network Solution

Quick Start Guide

http://www.3com.com/

http://www.3com.com/productreg

Part No. 09-2067-000

Published March 2001

3Com Corporation

■

5400 Bayfront Plaza

■

Santa Clara, California

■

95052-8145

■

U.S.A.

any form or by any means or used to make any derivative work (such as translation, transformation, or

adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to

time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied

or expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability,

satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the

product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license

agreement included with the product as a separate document, in the hard copy documentation, or on the

removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,

please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are

provided to you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense.

Software is delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995)

or as a “commercial item” as defined in FAR 2.101(a) and as such is provided with only such rights as are

provided in 3Com’s standard commercial license for the Software. Technical data is provided with limited rights

only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You

agree not to remove or deface any portion of any legend provided on any licensed program or documentation

contained in, or delivered to you in conjunction with, this User Guide.

Portions of this documentation are reproduced in whole or in part with permission from (as appropriate).

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not

be registered in other countries.

3Com and AirConnect are registered trademarks and the 3Com logo is a trademark of 3Com Corporation.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

Wi-Fi is a trademark of the Wireless Ethernet Compatibility Alliance.

All other company and product names may be trademarks of the respective companies with which they

are associated.

Ethernet Client Bridge

This quick start guide describes a basic installation and conﬁguration of the

3Com Ethernet Client Bridge (ECB).

For more detailed information, refer to the online user guide available on the

Installation

CD (see “Conﬁguring the ECB” on page 5 of this quick start guide

for more information on how to access the user guide).

Product Registration and Support

To register this product with 3Com, go to the following Web site:

http://www.3com.com/productreg

For support information and links to the latest available drivers and utilities, go

to the following Web site:

http://www.support.3com.com

ECB Kit Contents

In your Ethernet Client Bridge package, you will ﬁnd the following components:

■

Ethernet Client Bridge

■

RJ-45 Ethernet cable

■

5.2V Universal AC-to-DC power adapter

■

AC Power cord

■

DC Power cable

■

Printed quick start guide

■

Installation

CD containing a user guide and conﬁguration software

■

Mounting hardware

If any of these items are missing or damaged, please contact the place of

purchase or 3Com Customer Service (http://www.support.3com.com).

System Requirements

■

Ethernet LAN

■

Computer with Windows 95, 98, 2000, Windows NT, or Linux with X11

Windows Manager and GTK installed

■

Wi-Fi-compliant wireless LAN PC Card (such as an AirConnect

PC Card)

for each 3Com ECB

■

One standard straight-through 10BASE-T Ethernet cable

Quick Start Guide

■

One or more Wi-Fi-compliant access points if using a wireless

infrastructure network (check the 3Com service and support Web site at

www.support.3com.com for a list of access points supported by 3Com

Corporation).

Installing the ECB

1 Remove your ECB from the packaging. The ECB ships fully

assembled. To install the PC Card and use the ECB, some

disassembly and reassembly is required.

2 Remove the cap from the ECB by pulling on the side of the cap to

release it as shown in the following ﬁgure. When you remove the

cap, you will see the PC Card slot.

3 If you are planning to mount the ECB on the wall or ceiling

(optional), remove the bottom mounting plate as shown in the

following ﬁgure.

NOTE:

The ECB package does not include a Wi-Fi-compliant wireless

LAN PC Card. These cards are sold separately.

Ethernet Client

Bridge

Power

Alert

Wireless

Ethernet

Serial

Ethernet Client Bridge

4 Remove the small combs from the end cap. The combs are

generally not needed, but when cut to an appropriate size they

prevent the PC Card from vibrating out of the socket when the

ECB is in an environment with extreme vibrations.

5 Gently insert the PC Card (face up) into the slot as shown in the

following ﬁgure.

6 Replace the cap, which you removed in step 2, by snapping the

cap straight down on the body.

Ethernet Client

Bridge

Power

Alert

Wireless

Ethernet

Serial

Quick Start Guide

7 If you are mounting the ECB on a wall or ceiling, install the bottom

mounting plate, which you removed previously, where desired. After

the mounting plate is installed, place the ECB onto the mounting

plate and snap it into place. Ensure that the ECB is secure.

8 Connect a standard straight-through 10BASE-T Ethernet cable

between the RJ-45 port (ECB ports and connectors are shown

below) on the ECB and the network port on the computer where

you will install the ECB Conﬁguration Utility software.

9 Connect the six-pin DC power cable to the power adapter.

10 Connect the AC power cord to the other side of the power adapter.

11 Connect the round power plug to the ECB power jack labeled 5 VDC.

12 Insert the AC power cord into an AC socket.

13 Verify that the Ethernet LED on the ECB is illuminated.

14 The ECB hardware is now ready for conﬁguration using the ECB

Conﬁguration Utility software. Refer to the following section.

Serial port Configuration

button

10BASE-T

Ethernet port

Power

jack

5 VDC RJ-45 Serial Config.

Ethernet Client Bridge

Conﬁguring the ECB

The following is an overview of how to conﬁgure the ECB for Ethernet

bridging. Refer to the

ECB User Guide

for detailed conﬁguration information.

This user guide is a .pdf ﬁle that can be read or downloaded from the

Installation

CD.

Conﬁguration Procedure

1 Complete the “Installing the ECB” hardware installation procedure

above and verify that the Ethernet LED on the ECB is illuminated.

2 Insert the

Installation

CD into the CD-ROM drive of your computer.

If the installation program does not begin automatically, click

Computer

on your desktop. Click the icon for the drive in which

the

Installation

CD is located, and then double-click

setup.exe

3 Open the Ethernet Client Bridge List screen (see ﬁgure below).

4 Select and double-click your ECB unit from the list in the screen.

The Main Conﬁguration screen appears (see ﬁgure below).

NOTE:

You must have Adobe Acrobat Reader installed on your system to

read the

ECB User Guide

.pdf ﬁle. You can download the latest Adobe

Acrobat Reader from www.adobe.com.

Quick Start Guide

5 From the File menu, select

Reset to Default

to initialize the ECB to

the settings of your wireless LAN PC Card.

6 Select the

Radio

tab on the left-hand side of the screen. The Basic

Radio Conﬁguration screen appears (see following ﬁgure).

Ethernet Client Bridge

7 Set the ESSID to match the ESSID of your access point.

8 Enter a station (client) name to identify the Ethernet client that

your ECB is bridging to.

9 Click

Update and Reset Unit

at the bottom of the screen.

10 Verify that the ECB is associated with your access point by

checking that the Wireless LED on the ECB is green. The ECB is

now bridging to your wireless network.

11 Connect the ECB to the Ethernet device (such as a printer) you

intend to connect to your wireless network.

12 Turn the ECB power off, and then back on. Your Ethernet device is

now wireless!

Inhaltsverzeichnis

Andere 3Com Netzwerk-Router Handbücher

3Com

3Com OfficeConnect Remote 812 Bedienungsanleitung

3Com

3Com WL-602 Bedienungsanleitung

3Com

3Com OfficeConnect WL-542 Bedienungsanleitung

3Com

3Com OfficeConnect 3CRWE754G72-A Bedienungsanleitung

3Com

3Com 3C13886 - Router OC-3 ATM SML Flexible Interface... Bedienungsanleitung

3Com

3Com 3CRWE754G72-A Bedienungsanleitung

3Com

3Com AirProtect Sentry 5850 Bedienungsanleitung

3Com

3Com Router 6040 Bedienungsanleitung

3Com

3Com Router 3030 Bedienungsanleitung

3Com

3Com Router 3030 Bedienungsanleitung

3Com

3Com 3CNJ205 Bedienungsanleitung

3Com

3Com OfficeConnect 3CP4144 Einrichtungshandbuch

3Com

3Com NJ220 - IntelliJack Switch Bedienungsanleitung

3Com

3Com Router 6040 Bedienungsanleitung

3Com

3Com 3C16980A SuperStack3300 Bedienungsanleitung

3Com

3Com 3C8S400 - SuperStack II PathBuilder S400... Bedienungsanleitung

3Com

3Com OfficeConnect Remote 812 Bedienungsanleitung

3Com

3Com Router 3033 Bedienungsanleitung

3Com

3Com Router 3030 Bedienungsanleitung

3Com

3Com 3C13751 Bedienungsanleitung

3Com

3Com OfficeConnect Ethernet Hub 16C Bedienungsanleitung

3Com

3Com USB Network Interface Bedienungsanleitung

3Com

3Com OfficeConnect 3CRWDR101A-75 Bedienungsanleitung

3Com

3Com 3C13636 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise