3Com AirConnect 9550 Bedienungsanleitung

Part Number 10016854 Rev. AA

Published May 2008

Quick Start Guide

3Com®AirConnect®9550

11n 2.4+5GHz PoE Access Point

3CRWE955075 / WL-605

3Com®AirConnect®9150

11n 2.4GHz PoE Access Point

3CRWE915075 / WL-604

Guide de mise en route…11

Français

Guida introduttiva…21

Italiano

Kurzanleitung…31

Deutsch

Guía de inicio rápido…41

Español

Guia de Início Rápido…51

Portuguese

any form or by any means or used to make any derivative work (such as translation, transformation, or

adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to

time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied

or expressed, including, but not limited to, the implied warranties, terms, or conditions of merchantability,

satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the

product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license

agreement included with the product as a separate document, in the hardcopy documentation, or on the

removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,

please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGENDS:

If you are a United States government agency, then this documentation and the software described herein are

provided to you subject to the following:

United States Government Legend: All technical data and computer software is commercial in nature and

developed solely at private expense. Software is delivered as Commercial Computer Software as defined in

DFARS 252.227-7014 (June 1995) or as a commercial item as defined in FAR 2.101(a) and as such is provided

with only such rights as are provided in 3Com’s standard commercial license for the Software. Technical data is

provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987),

whichever is applicable. You agree not to remove or deface any portion of any legend provided on any licensed

program or documentation contained in, or delivered to you in conjunction with guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not

be registered in other countries.

3Com, the 3Com logo, and AirConnect are registered trademarks of 3Com Corporation.

Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United

States and/or other countries. Oracle is a registered trademark of Oracle Corporation.

All other company, brand, and product names may be registered trademarks or trademarks of the respective

companies with which they are associated.

Quick Start Guide

3Com®AirConnect®9550

11n 2.4+5GHz PoE Access Point

3CRWE955075 / WL-605

3Com®AirConnect®

9150 11n 2.4GHz PoE Access Point

3CRWE915075 / WL-604

This Quick Start Guide describes the basic steps necessary to install and configure your 3Com

AirConnect 9550 11n 2.4+5GHz PoE Access Point and 3Com AirConnect 9150 11n 2.4GHz PoE

Access Point. Note: This guide refers to these devices as the Access Point or AP.

Before you install or move the AP, you must carefully read the safety information provided in

“Safety Information” on page 3 of this manual.

About This Guide

This guide describes the basic installation of the AP. It covers these topics:

•AP Features

•Register Your Product for Services and Repair

•Safety Information

•1: Unpacking the AP

•2: Preparing for Installation

•3: Mounting the AP

•4: Connecting Power

•5: Checking the LED Indicators

•6: Installing Software

•7: Connecting to the AP

•8: Configuring the AP

•Troubleshooting

AP Features

Feature Description

Ethernet Port The Ethernet port provides a 10/100/1000 BASE-T Ethernet connection

to a switch. Use a suitable Category 5 cable with straight-through

wiring and standard RJ-45 connectors to connect your AP to the

network.

LEDs The LEDs indicate power and activity. See “Checking the LED

Indicators” on page 8 for details.

Antenna Connectors The AP has three built-in internal antennas. In addition, three RSMA

antenna connectors allow you to connect optional external antennas.

Reset Button To restore factory settings, during power-up, press the Reset button and

hold it for 5 or more seconds.

RJ-45 Console Port Provides a serial interface to the AP for diagnostic use. Default: 115.2K

speed, 8 bits, no parity, 1 stop bit.

Wall-Mounting Bracket

and Table-Top Stand

The combined wall-mounting bracket and table-top stand allows you to

mount the unit on a wall or stand it on a table top.

Ethernet Port

Wall Mounting Bracket/

Connectors for optional antennas

LEDs

RJ-45 Console Port

Reset Button

Table Top Stand

Slots for desktop

mounting

Slots for wall

mounting

To obtain telephone support as part of your warranty and other service benefits, you must first

http://eSupport.3com.com/

Telephone Technical Support and Repair

3Com offers telephone, e-mail, and Internet access to technical support and repair services. To

access these services for your region, use the appropriate telephone number, URL, or e-mail

address from the following URL:

http://csoweb4.3com.com/contactus/

Safety Information

This equipment must be installed in compliance with local and national building codes, regulatory

restrictions, and FCC rules. For the safety of people and equipment, only professional network

personnel should install the AP.

You must read the following safety information carefully before you install or remove the

unit.

Approved Channels

Use of this product is only authorized for the channels approved by each country. For proper

installation, select your country from the country-selection list.

To conform to FCC and other country restrictions, your product may be limited in the channels

that are available. If other channels are permitted in your country, please visit the 3Com web site

for the latest software version:

www.3Com.com

WARNING: Warnings contain directions that you must follow for your personal safety.

Follow all directions carefully.

WARNING: Exceptional care must be taken during installation and removal of the unit.

WARNING: This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 950 / IEC 60950. The conditions are only maintained if the equipment

to which it is connected also operates under SELV conditions.

WARNING: There are no user-replaceable fuses or user-serviceable parts inside the

unit. If you have a physical problem with the unit that cannot be solved with problem

solving actions in this guide, contact your supplier.

WARNING: RJ-45 ports. These are RJ-45 data sockets. They cannot be used as

standard traditional telephone sockets, or to connect the unit to a traditional PBX or

public telephone network. Only connect RJ-45 data connectors, network telephony

systems, or network telephones to these sockets.

Either shielded or unshielded data cables with shielded or unshielded jacks can be

connected to these data sockets.

WARNING: To comply with FCC radio frequency (RF) exposure limits, a minimum

body-to-antenna distance of 20 cm (8 in.) must be maintained when the AP is

operational.

1. Unpacking the AP

Make sure that you have the following items, which are included with the AP:

•One 3Com AirConnect 9550 Access Point or 3Com AirConnect 9150 Access Point

•Wall-mounting hardware:

•1 combined wall-mounting bracket and table-top stand

•4 screws

•4 wall anchors

•8 adhesive rubber feet

•1 CD-ROM containing the WIDMan Utility software

•1 copy of this Quick Start Guide

•One 3Com Warranty document

2. Preparing for Installation

3Com recommends that you connect and check the Ethernet cable and LEDs before you install the

AP in a hard-to-reach location. Also, observe these items before you mount or connect the AP:

Feature Description

Switch Port To connect your wireless network to your wired network, you need a

switch that is connected to the AP.

Cabling Make sure that a standard Ethernet cable with straight-through wiring

is installed at the site before you install the AP.

Make sure that the cable is highly flexible and that the RJ-45 connector

has no extra covering that could prevent the cable from being routed

through the mounting bracket.

Power Requirement Power is supplied using an 802.3af Power Over Ethernet (PoE)

compliant device such as a PoE switch or a PoE injector (also called a

PoE midspan). Example: 3CNJPSE-GIG. For maximum performance,

3Com recommends that you use a Gigabit link.

MAC Address Record the AP MAC address in a safe place before the AP is installed in

a hard-to-reach location.

The MAC address is printed on the back of the AP. Additional MAC

address labels are shipped with the AP.

3. Mounting the AP

The AP can be mounted on the following types of surfaces:

•Wall or electrical box (NEMA enclosure)

•Table top

Wall or Electrical Box Mounting

To install your AP on a wall or electrical box, use the mounting bracket that comes with the

device. Follow these steps:

1Following these guidelines, screw the mounting bracket to a wall or electrical box (NEMA

enclosure):

•The mounting bracket tabs should be pointing upward.

•If mounting to drywall, use the 4 screws and 4 wall anchors.

•If mounting to an EU electrical box (60.3mm), use 2 threaded screws and insert into the

holes marked “A” in the diagram shown below.

•If mounting to a US electrical box (83.3mm), use 2 threaded screws and insert into the

holes marked “B” in the diagram shown below.

2Connect the Ethernet cable (for power and network connection) to the LAN port on the back

of the AP.

3To mount the AP onto the mounting bracket, insert the mounting-bracket tabs into the slots

on the back of the AP.

CAUTION: If you are mounting the AP on a wall, you cannot use the slots on the bottom narrow

edge of the device. Instead, you must use the slots on back of the AP.

Tabletop Mounting

To install the AP on a flat surface such as a table or desktop, follow these steps:

1Insert the tabs on the table stand into the slots on the side of the AP, as shown in the

illustration. Align the cable routing cut out toward the upper part of the stand.

2To lock the stand to the AP, slide the stand back and the AP forward, as shown here:

3Place the AP and table stand on the table.

4Connect the Ethernet cable for power and network connection to the LAN port on the back

of the AP.

Cable routing cut out

4. Connecting Power

This section describes how to power the AP in either of these ways:

•By Power Over Ethernet (PoE) supplied over the LAN by an 802.3af PoE compliant device

such as a switch.

•By PoE supplied by a PoE injector or midspan (not included with the AP).

Power over Ethernet (PoE) from the LAN

To power the AP using PoE provided by a switch or other 802.3af compliant device, plug the

network cable from the device into the AP’s Ethernet port.

Power over Ethernet from a PoE Injector

To power the AP using a PoE injector or midspan (not included), follow these steps:

1Connect the LAN cable from a switch to the Switch port on the PoE injector. 3Com

recommends that you use a Gigabit PoE injector such as 3CNJPSE-GIG

2Connect a LAN cable from the Ethernet port on the AP to the other LAN port on the PoE

injector.

3Plug the PoE injector into a properly grounded electric outlet. See the illustration.

PoE Switch

Access Point

Switch

(non-PoE)

Access Point

To Access Point

To Switch

5. Checking the LED Indicators

When the AP is connected to power, LEDs indicate activity as follows:

6. Installing Software

The following application is included on the 3Com WIDMan Utility CD-ROM:

•Wireless Infrastructure Device Manager (WIDMan Utility)

To discover and configure the AP, you must first install the Wireless Infrastructure Device Manager

software (WIDMan) on your computer.

1Turn on your computer.

2Insert the 3Com Installation CD into the CD-ROM drive.

The CD menu appears. If it does not appear, start the Setup menu from the Windows Start

menu. For example: Start > Run > d:\autorun.exe

3On the menu, click Install/Uninstall WIDMan.

4On the next screen, double-click 3Com Wireless Infrastructure Device Manager and then

click Install. The installation begins.

5Follow the instructions on each screen to complete the installation. If prompted, reboot the

computer.

Indicator Color State Description

LED 1

(Power/

System)

Off No power

Amber On Failure of CPU or system

Blinking System initiation or reset (software self-

testing and loading)

Green On Powered on and ready for operation

LED 2

(2.4G)

Green Off Radio disabled

On Radio enabled

Blinking Activity

LED 3

(5G)

(on the 3Com

AirConnect 9550

Access Point only)

Green Off Radio disabled

On Radio enabled

Blinking Activity

LED 4

(Ethernet)

Off No 10/100/1000 BASE-T link detected, or

administratively disabled

Amber On 10/100 BASE-T link detected; no activity

Blinking 10/100 BASE-T link activity

Green On 1000 BASE-T link detected; no activity

Blinking 1000 BASE-T link activity

Andere Handbücher für AirConnect 9550

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere 3Com Drahtloser Zugangspunkt Handbücher

3Com

3Com AirProtect Sensor 5750 Bedienungsanleitung

3Com

3Com AP2750 Bedienungsanleitung

3Com

3Com AirConnect 9550 Bedienungsanleitung

3Com

3Com AirConnect 9550 Installationsanleitung

3Com

3Com 3CRWX395075A - Wireless LAN Managed Access Point... Bedienungsanleitung

3Com

3Com 3CRWE91096A - Wireless LAN Building-to-Building... Bedienungsanleitung

3Com

3Com WL-607 Bedienungsanleitung

3Com

3Com Wireless LAN 11 Mbps Bedienungsanleitung

3Com

3Com Wireless 11n USB Adapter Bedienungsanleitung

3Com

3Com 8250 Bedienungsanleitung

3Com

3Com WL-455 Bedienungsanleitung

3Com

3Com 8760 - Wireless Dual Radio 11a/b/g PoE Access... Bedienungsanleitung

3Com

3Com 3CRWE870075A - Wireless LAN Access Point... Bedienungsanleitung

3Com

3Com 3CRWE876075 / WL-546 Bedienungsanleitung

3Com

3Com 8000 Bedienungsanleitung

3Com

3Com 3CRWX275075A - Wireless LAN Managed Access Point... Bedienungsanleitung

3Com

3Com AirConnect Bedienungsanleitung

3Com

3Com AP7760 Bedienungsanleitung

3Com

3Com 3CRWE675075 - 11a/b/g Wireless LAN Workgroup... Bedienungsanleitung

3Com

3Com 3CRWX315075A - Wireless LAN Managed Access Point... Bedienungsanleitung

3Com

3Com 3CRGPC10075 Bedienungsanleitung

3Com

3Com 8500 Bedienungsanleitung

3Com

3Com OfficeConnect 3CRWE454A72 Bedienungsanleitung

3Com

3Com 7250 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung