A.O. Smith CONSERVATIONIST BTPV-650A Bedienungsanleitung

A 107.0

Revised December 2004

COMMERCIAL GAS DIRECT VENT

TANK-TYPE WATER HEATERS

BTP-540A, BTPV-540A, BTP-650A,

BTPV-650A, BTP-740A, BTPV-740A

STANDARD FEATURES

Meets ASHRAE/IES 90.1-1999 thermal efficiency and standby loss

requirements. Meets SCAQMD Low NOx requirements.

Professional Start-Up is provided.

BTP ATMOSPHERIC CONVENTIONAL (Vertical Venting) — A barometric

draft regulating damper is provided.

BTPV HORIZONTAL AND DIRECT VENT — Optional vent kits allow for

sidewall venting or direct venting.

GLASS-LINED TANK — Exclusive corrosion protection with glass-lining

and nickelous oxide on all interior tank surfaces. Multiple anodes provide

corrosion protection. Factory installed A.G.A./ASME rated Temperature and

Pressure relief valve.

POWERED GAS BURNER — Premix Low NOx burner design with internal

FGR. Features an internal blocked flue sensor, separate pilot system, internal

thermal cutoff & anti-flashback barrier. Inlet gas pressures: 14" W.C. max.,

8" W.C. min. natural gas only.

FULLY AUTOMATIC CONTROLS — Safety shut off, high temperature limit

control, dual thermostat (adjustable 120°F thru 180°F) for accurate

temperature control.

HIGH ALTITUDE INSTALLATION — Equipped with adjustable air intake

damper, easy to reset for high altitude installation by Authorized BTP

Start-Up agent.

DRAFT EQUALIZING COMBUSTION CHAMBER — Patented dome system

balances pressures inside the combustion chamber to ensure even heat

distribution, optimum flue loading and maximum heat transfer.

THICK PERMAFOAM INSULATION — Saves fuel, reduces standby heat loss.

JACKET — Is of heavy gauge steel with baked enamel finish over bonderized

undercoat.

U.L. CERTIFIED.

ASME CONSTRUCTION — Rated working pressure 160 PSI.

A.G.A./ASME TEMPERATURE & PRESSURE RELIEF VALVE — Factory installed.

OTHER FEATURES

• Two layers of high temperature ceramic fiber insulation surrounding

combustion chamber • Flame inspection port opening • Mounted on rugged

channel iron skids • Multiple anodes for protection.

EASY CLEANING — One handhole clean out provided.

CAUTION: Must be installed on noncombustible surface.

Based on 80% thermal efficiency obtained in A. O. Smith engineering laboratories.

NOTE: To compensate for the effects of high altitude areas above 2000 feet, recovery ratings

should be reduced approximately 4% for every 1000 feet above sea level.

Low NOx Certified

LIMITED WARRANTY OUTLINE

If the tank should leak anytime during the first three

years, under the terms of the warranty, A.O. Smith

will furnish a replacement heater less burner and

controls; installation, labor, handling and local de-

livery extra.

THIS OUTLINE IS NOT A WARRANTY.

For complete information, consult the written

warranty or A.O. Smith Water Products Company.

Warranty does not apply to product installed

outside of the United States of America or its

territorial possessions and Canada.

Storage Input Recovery Recovery Rating

Capacity Rating Rating Rating Current Draw

U.S. Gals. BTU/HR. GPH GPH 120V

Models (Litres) Nat. 100°°

°°

°F Rise 140°°

°°

°F Rise 60Hz 1 Phase

BTP(V)-540A 85 (261) 540,000 523 374

BTP(V)-650A 85 (261) 650,000 630 450

BTP(V)-740A 85 (261) 740,000 718 512

6.0 Amps

CONSERVATIONIST

Printed in U.S.A.

A 108.0

A. O. Smith Corporation reserves the right to make product changes

or improvements at any time without notice.

A. O. Smith

Water Products Company

Ashland City, TN

A Division of A. O. Smith Corporation

A. O. Smith Water Products Company, Inc.

On Line www.aosmithwaterheaters.com

For Technical Information and

Automated Fax Service

Phone: 800-527-1953

BTP(V) SUGGESTED SPECIFICATION

GENERAL

Water heater(s) shall be Model______________as manufactured by A.O. Smith or equal. Water heater(s) shall be of glass-lined design and include a

powered gas burner, redundant main gas valves, gas pressure regulator and flame inspection port. Heater(s) shall have an input rating of ______and a

recovery rating of_________GPH at a temperature rise of 100°F with a maximum storage capacity of 85 gallons. Heater(s) shall be equipped with 1-1/2"

NPT water inlet and outlet openings and a boiler-type handhole cleanout. Heater(s), for barometric venting and under UL795 for sidewall/direct venting,

shall be constructed and stamped in accordance with ASME Boiler and Pressure Vessel Code and be so marked for a maximum working pressure of 160

psi. Heaters shall include a high temperature limit control, dual bulb thermostat for accurate temperature control and anti-stacking compensation and a

factory installed A.G.A. rated temperature and pressure relief valve. Heater(s) shall be equipped with multiple anodes for corrosion protection, insulated

with polyurethane foam, and meet ASHRAE/IES 90.1-1999 requirements for thermal efficiency and standby loss, and meet SCAQMD R1146.2 low NOx

requirements. Heater(s) shall have a minimum thermal efficiency 80%. The outer jacket shall have a baked enamel finish over a bonderized undercoat. All

internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to

steel by firing at a temperature range of 1,400°F. Heater(s) tank shall have a 3 year limited warranty against corrosion as outlined in the written warranty.

METHOD OF VENTING

BTP heater(s) shall be factory supplied with a Barometric Draft Regulator for conventional atmospheric venting using conventional venting materials.

BTPV heater(s) shall be supplied with an optional vent kit allowing for horizontal sidewall venting or direct venting.

BURNER AND CONTROLS

Burner(s) shall be of the premix with internal FGR & thermal cutoff design. Design shall include a separate spark pilot ignition system. In addition,

burner(s) shall have an integral blocked flue sensor, glass view port, main gas regulator, automatic gas valve, manual test cock and manual gas shutoff

valve. Burner(s) must be factory installed, tested and started by an A. O. Smith Authorized BTP start-up agent before placing the unit(s) into operation.

ALL DIMENSIONS IN INCHES (MILLIMETERS)

Gas Approx.

Models A B C D** E*** F G H I Conn. Ship. Wt.

80 3/4 73 32 1/4 9 6 26 1/2 93 29 1/2 48 1/2 1* 950

2,051 1,854 819 229 152 673 2,362 749 1,232 25.4 431 kg

80 3/4 73 32 1/4 9 8 26 1/2 93 29 1/2 48 1/2 1* 950

2,051 1,854 819 229 203 673 2,362 749 1,232 25.4 431 kg

80 3/4 73 32 1/4 9 8 26 1/2 93 29 1/2 48 1/2 1* 950

2,051 1,854 819 229 203 673 2,362 749 1,232 25.4 431 kg

*Minimum gas supply pipe is 1 1/4”, reference Manual, Table 7 for gas supply pipe size.

** D dimension is for atmospheric vent size.

*** E dimension is for direct and side-wall vent size.

BTP(V)-540A

BTP(V)-650A

BTP(V)-740A

Dieses Handbuch passt für folgende Modelle

Andere A.O. Smith Boiler Handbücher

A.O. Smith

A.O. Smith FGR 100 Bedienungsanleitung

A.O. Smith

A.O. Smith FPS 75 Handbuch

A.O. Smith

A.O. Smith ITES Series Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith HSE-SES-025 Bedienungsanleitung

A.O. Smith

A.O. Smith BTF-80 Bedienungsanleitung

A.O. Smith

A.O. Smith GDVH-40 Bedienungsanleitung

A.O. Smith

A.O. Smith BURKAY HW-120M Anwendungshandbuch

A.O. Smith

A.O. Smith 185874-001 Bedienungsanleitung

A.O. Smith

A.O. Smith HSE-SDS-006 Bedienungsanleitung

A.O. Smith

A.O. Smith PROMAX SL RXLD-52 Bedienungsanleitung

A.O. Smith

A.O. Smith 120 through 250 Series Anleitung zur Verwendung

A.O. Smith

A.O. Smith RESIDENTIAL GAS WATER HEATER Bedienungsanleitung

A.O. Smith

A.O. Smith GCV/XCV 65/65L Bedienungsanleitung

A.O. Smith

A.O. Smith CYCLONE XHE BTH 300A Bedienungsanleitung

A.O. Smith

A.O. Smith CYCLONE Xi BTH 500A Bedienungsanleitung

A.O. Smith

A.O. Smith Voltex series Produktinformationsblatt

A.O. Smith

A.O. Smith Gdhe 50 Bedienungsanleitung

A.O. Smith

A.O. Smith GWV - 120 Handbuch

A.O. Smith

A.O. Smith TC-049-R2 Anleitung zur Verwendung

A.O. Smith

A.O. Smith DRE PLUS Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith MEV 50 EC Bedienungsanleitung

A.O. Smith

A.O. Smith 1000 SERIES 100 Bedienungsanleitung

A.O. Smith

A.O. Smith THR-160 Produktinformationsblatt

A.O. Smith

A.O. Smith ProMax Direct-Vent GDV-40 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung