ABB Baldor BC145 Montageanleitung
MN1373
Installation & Operating Manual
4/17
BC145 SIGNAL ISOLATOR BOARD
Any trademarks used in this manual are the property of their respective owners.
Important:
Be sure to check www.baldor.com to download the latest version of this manual in Adobe Acrobat PDF format.
iMN1373
Chapter 1
Introduction
Safety Warning .............................................................................1-1
General Performance Specifications .............................................................1-4
Chapter 2
Installation
Mounting Instructions........................................................................... 2-1
Chapter 3
Wiring
AC Power .................................................................................3-1
Input Terminals .............................................................................3-2
Current Signal Input .........................................................................3-2
Voltage Signal Input .........................................................................3-4
Chapter 4
Adjustments
Output Signal ..............................................................................4-1
Table of Contents
1-1 MN1373
Chapter 1
Introduction
Introduction
The BC145 Signal Isolator is used to isolate, amplify and condition DC voltage and current signals from any source (motors,
tachs and transducers) which will provide most adjustable speed motor controls with a voltage following input. The
maximum output voltage of the isolator is 10 volts which is a linear function of the input signal.
The BC145 is versatile since it can accommodate a wide range of input voltages (0-25*, 0-120 and 0-550VDC) and, in
addition, a wide range of input current signals (4-20mA, 10-50mA and 1-5mA). The Voltage/Current (“VLT/CUR”) jumper is
used to change the BC145 from a voltage to current input.
BC145 is a unipolar input, providing 0-10V input. For Regenerative Drives with bipolar ±10V input, other Signal Isolators are
available.
A built-in power supply enables the BC145 to be controlled with a 5KΩ remote potentiometer (connect potentiometer to
terminals “P1”, “5” and “6”). The potentiometer can also be wired for Auto/Manual Operation.
*The input range of 0-25V is the maximum voltage that can be applied to terminals “5” and “6”. The minimum input voltage
is 0-5 volts which can achieve an output voltage of 0-10 volts. The unit is factory calibrated so that a 0-10VDC input yields a
0-10VDC output.
SAFETY NOTICE
A Warning statement indicates a potentially hazardous situation which, if not avoided, could result in injury or death.
A Caution statement indicates a potentially hazardous situation which, if not avoided, could result in damage to property.
A Note indicates additional information that is not critical to the installation or operation.
WARNING: This equipment may contain voltages as high as 1000 volts! Electrical shock can cause serious or fatal injury. Only qualified
personnel should attempt the start-up procedure or troubleshoot this equipment.
WARNING: Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that all grounding
instructions have been followed. Electrical shock can cause serious or fatal injury.
1-2MN1373
SAFETY NOTICE Continued
WARNING: Electrical shock can cause serious or fatal injury. Be sure that all power is disconnected and there is no voltage present
from this equipment or equipment to which it is or will be connected. Electrical shock can cause serious or fatal injury. Only
qualified personnel should attempt the installation and start-up procedures.
WARNING: Electrical shock can cause serious or fatal injury. Verify there is no voltage phase-to-phase or phase-to-neutral at the motor
leads before connecting motor to this control. Motor may have high voltage present even when disconnected from this control.
WARNING: Do not use motor overload relays with an automatic reset feature. These are dangerous since the process may injure someone
if a sudden or unexpected automatic restart occurs. If manual reset relays are not available, disable the automatic restart
feature using external control wiring.
WARNING: This unit has an automatic restart feature that will start the motor whenever input power is applied and a RUN (FWD or REV)
command is issued. If an automatic restart of the motor could cause injury to personnel, the automatic restart feature should
be disabled.
WARNING: Using a jumper to eliminate the start/stop function will cause the motor to run at the Main Speed Potentiometer setting when
the AC line is applied.
WARNING: If possible, do not adjust trim pots with the main power applied. Electrical shock can cause serious or fatal injury. If
adjustments are made with the main power applied, an insulated adjustment tool must be used to prevent shock hazard and
safety glasses must be worn.
WARNING: Do not use this drive in an explosive environment. An explosion can cause serious or fatal injury. This drive is not explosion
proof.
WARNING: When the Enable jumper is installed, the drive and motor will start and run when AC power is applied, when power is restored
after a momentary power loss, or after an overload or TCL fault is reset. The user must ensure that automatic start up of the
driven equipment will not cause injury to operating personnel or damage to the driven equipment. The user is responsible
for providing suitable audible or visual alarms or other devices to indicate that the drive may start at any moment. Failure to
observe this warning could result in severe bodily injury or loss of life.
WARNING: Do not use start/stop, inhibit or enable functions as a safety disconnect. Use only an AC line disconnect for that purpose.
Failure to observe this warning could result in severe bodily injury or loss of life.
Caution: Disconnect motor leads (A1 and A2) from control before you perform a Dielectric Withstand test on the motor. Failure to
disconnect motor from the control will result in extensive damage to the control. The control is tested at the factory for high
voltage / leakage resistance as part of Underwriter Laboratory requirements.
1-3 MN1373
SAFETY NOTICE Continued
Caution: Do not connect AC power to the Motor terminals A1 and A2. Connecting AC power to these terminals may damage the control.
Caution: Baldor recommends not to use Grounded Leg Delta transformer power leads that may create ground loops. Instead, we
recommend using a four wire Wye.
Caution: Suitable for use on a circuit capable of delivering not more than 5,000 RMS symmetrical short circuit amperes listed here at
rated voltage.
Caution: Adjusting the current limit above 150% of the motor nameplate rating can cause overheating and demagnetization of the PM
motor.
Caution: Do not leave the motor in a locked rotor condition for more than a few seconds since motor damage may occur.
Caution: Shunt wound motors may be damaged if field windings remain energized for an extended period of time without armature
rotation.
Receiving
Each control is thoroughly tested at the factory and carefully packaged for shipment. When you receive your control, there
are several things you should do immediately.
1. Observe the condition of the shipping container and report any damage immediately to the commercial carrier that
delivered your control.
2. Verify that the part number you received is the same as the part number listed on your purchase order.
3. Do not unpack until ready for use.
1-4MN1373
Table 1-1 General Performance Specifications
Description Specification
AC Power Requirements 115 or 208-230VAC, 50/60Hz (1)
Signal Input Voltage
(2)
0-25, 0-120, 0-550VDC
Signal Input Current
(2)
1-5, 4-20, 10-50mA (3)
Maximum Output Voltage 10 volts
Maximum Output Current 10mA
Range of “MIN” Trimpot ±3 volts
Range of “MAX” Trimpot 0 to 2 times the input voltage with maximum of 10 volts
Linearity (4) ±0.1%
Temperature Drift (4) 4mV per °C
Temperature Operating Range 0-40°C / 32-104°F
Operating Humidity Range (% Relative, Non-Condensing) 0 - 95
Storage Temperature -25 to +85°C / -13 to +185°F
Note: (1) To achieve full specifications, input voltage must be within ±10% of nominal.
(2) Floating (non-grounded) or grounded input signal may be used.
(3) To convert from 4-20mA to 1-5mA, add a 1kΩ 1/4W resistor across terminals “5” and “6”. To convert to 10-5-mA, add a 150Ω 1W
resistor across terminals “5” and “6”. See Figure 3-3.
(4) Specifications are based on an output of 10 volts.
2-1 MN1373
Chapter 2
Installation
Mounting Instructions
Mount the Signal Isolator using (4) 6-32 screws (not included). Use the Control Layout and Mechanical Specifications drawing
to locate the mounting holes. The unit is designed to be mounted in any position providing its components do not come in
contact with grounded or live wiring.
2-1 Control Layout & Mechanical Specifications (Inches/[mm])
(Illustrates Factory Setting of Jumper J1)
3-1MN1373
Chapter 3
Installation
Wiring
WARNING: READ SAFETY WARNINGS BEFORE ATTEMPTING TO USE THIS CONTROL.
Caution: To avoid erratic operation, do not bundle AC Line and motor wires with potentiometer, voltage following, enable, inhibit or other
signal wiring. Use shielded cables on all signal wiring over 12” (30cm). The shield should be earth grounded on the control
side only.
AC Power
The BC145 is powered with either 115 or 230VAC, 50/60 Hz by arranging the jumpers between terminals “1” to “4” properly.
See Figures 3-1 and 3-2. Be sure unit is wired in accordance with the National Electrical Code and other codes that may
apply. It is recommended that a 1 amp fuse be installed in series with the AC line.
3-1 115V Connection
3-2 MN1373
3-2 230V Connection
Input Terminals
A voltage or current signal from a microprocessor, tachometer, transducer, etc. is to be connected to terminals “5” through
“8”. The selection of the proper terminal is based on the maximum level of the input signal. See Figure 3-3, Table 3-1 and
Figure 3-4.
Current Signal Input
WARNING: READ SAFETY WARNINGS BEFORE ATTEMPTING TO USE THIS CONTROL.
The Signal Isolator accepts 4-20mA DC input to provide 0-9VDC output. Connect the current signal input common (-) to
Terminal “5” and the positive (+) to Terminal “6”, as shown in Figure 3-3. Other current signal input ranges can also be used
by installing appropriate resistors across terminals 5 and 6. Calibrate the Signal Isolator in accordance with the procedure
described below.
Note: Two resistors for 10-50mA and 1-5mA inputs are supplied in the hardware bag included with this kit.
Inhaltsverzeichnis
Andere ABB Industrieelektrik Handbücher
ABB
ABB Tmax RC223 T3 Bedienungsanleitung
ABB
ABB ACS880-607 Series Bedienungsanleitung
ABB
ABB 6AGC085345 Bedienungsanleitung
ABB
ABB SACE Emax 2 E2.2 Bedienungsanleitung
ABB
ABB Type A Bedienungs- und Wartungshandbuch
ABB
ABB ACS850 series Fehlerbehebungshandbuch
ABB
ABB UZE Bedienungsanleitung
ABB
ABB EBS862 Bedienungsanleitung
ABB
ABB JSM D28 Handle profile Bedienungsanleitung
ABB
ABB Arc Guard System TVOC-2-COM Merkblatt
ABB
ABB Emax Bedienungsanleitung
ABB
ABB DCS800 Bedienungsanleitung
ABB
ABB TA515 CASE Bedienungsanleitung
ABB
ABB V-Contact VSC Series Kurzanleitung
ABB
ABB SACE Tmax XT UL Bedienungsanleitung
ABB
ABB SACE PR010/K Bedienungsanleitung
ABB
ABB VD4 Series Kurzanleitung
ABB
ABB Cylon MATRIX-2 Bedienungsanleitung
ABB
ABB Tmax XT XT3 Montageanleitung
ABB
ABB SACE Emax 2 Bedienungsanleitung
Beliebte Industrieelektrik Handbücher anderer Marken
Rexroth Indramat
Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch
Abtech
Abtech HVJB Series Leitfaden
Murata
Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung
SAF-HOLLAND
SAF-HOLLAND CBX 5415.5 Bedienungsanleitung
Eaton
Eaton Ulusoy HMH24-04 Bedienungsanleitung
Newlong
Newlong NP-7H Bedienungsanleitung
Murata
Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung
Stahl
Stahl 8575/12 Bedienungsanleitung
SI
SI Pegasus Bedienungsanleitung
Murata
Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung
Murata
Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung
Cooper Power Systems
Cooper Power Systems VXE15 Bedienungsanleitung
S&C
S&C Vista SD Bedienungsanleitung
Murata
Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung
Siemens
Siemens 3VA9988-0BM10 Bedienungsanleitung
Siemens
Siemens SITRANS LVS100 Bedienungsanleitung
Murata
Murata GRM32ER60G227ME05 Series Bedienungsanleitung
Siemens
Siemens SENTRON SUPERSWITCH 3KL82 Series Bedienungsanleitung