ABB PS S18-300 Bedienungsanleitung

Softstart Changing of

Printed Circuit Board

PS S18 - 300

5309 704-1 Rev2 May-03

- 2-

Please note!

The life span of electronics can be affected by damage caused by electrostatic

discharge. This can happen if a charged tool or person touches a component.

Therefore it is very important that all tools and personnel are discharged by touching an

earthed point before the printed

circuit board or any of the components are touched. It is equally important to

discharge the package with the new component before opening it.

A person walking on a carpet can be charged with up to fifteen

thousand volt (15000V). Compare this with the fact that some sensitive

components can be destroyed when discharged on a much lower level

(about 100V). We kindly ask you to pay notice to this, as this is a vital point in order to

ensure the life span of the product.

NEWS - Different versions of PCB

It exist two different version of PCB’s out in the field. The difference is the

terminals for all internal connections like gate-cables, fan-cables etc.

This kit is suitable for exchange the PCB, both the old and the new version of PCB.

In this kit you find the PCB with the new terminals. If you then have an old type of

product, with the old type of PCB, you will need to cut the old connections to the

PCB and exchange them to the new ones added in this kit. The position / location

for each new terminal is shown in picture no 2 below.

Step by step.

1. Disconnect the voltage from terminals 1L1, 3L2, and 5L3 (main supply).

2. Disconnect all cables from the terminals 1 to.12.

3. Remove the front cover.

4. Discharge the tools and yourself by touching earth (if you are not earthed).

5. Remove the old P.C.B.

6. Disconnect the cable on the P.C.B. from the thyristors, fans and thermal switch.

7. Check if you have the old type of PCB or the new one. If the terminals are of the

same type you have a new PCB. If so go to No 9 below.

8. If you have the old type of PCB, cut the old wires, and exchange the terminals for the

gate wires, fan wires, and thermal switch to the new ones included in the package.

9. Discharge the package with the new P.C.B by moving it to earth.

10. Mount the cable on the P.C.B. from the thyristors, fans and thermal switch.

See Fig1

11. Mount the new P.C.B.

12. Mount the front cover.

13. Connect the voltage and the other cable.

Ready for start!!

- 3-

This picture shows the old

type of PCB. On the next page

you find the new type, with

the new terminals.

Figure 1

- 4-

ABB Automation Technology Products AB, Control

S-721 61 Västerås, SWEDEN

Telephone +46 21 32 07 00

TELEFAX +46 21 12 60 01

(Changing PCB PS rev 2 S.DOC

Figure 2 – view from the front of the PCB (component side).

The New PCB with all new added connections including

short cables, which need to be connected to the old

wires.

PS – make sure that you are placing the

jumper for supply voltage in the correct

position , 110 – 120V or 220 – 240V DS

Inhaltsverzeichnis

Andere ABB Industrieelektrik Handbücher

ABB

ABB SACE Tmax XT Series Bedienungsanleitung

ABB

ABB EBS862 Bedienungsanleitung

ABB

ABB Three Phase Mechanical AutoLink Bedienungsanleitung

ABB

ABB PCS100 AVC-40-1B Bedienungsanleitung

ABB

ABB 6AGC085345 Bedienungsanleitung

ABB

ABB SACE Emax 2 Bedienungsanleitung

ABB

ABB UCC Series Bedienungsanleitung

ABB

ABB Ekip E-Hub Bedienungsanleitung

ABB

ABB ACS880 Series Bedienungsanleitung

ABB

ABB Relion 615 series Datenblatt

ABB

ABB OVR-15 Bedienungs- und Wartungshandbuch

ABB

ABB UEKE 3A1 Bedienungsanleitung

ABB

ABB VD4 Series Kurzanleitung

ABB

ABB ILTS-E Series Bedienungsanleitung

ABB

ABB TMAX XT XT7M Montageanleitung

ABB

ABB Baldor BC145 Montageanleitung

ABB

ABB Zenith ZT30 Bedienungsanleitung

ABB

ABB ACS850 series Fehlerbehebungshandbuch

ABB

ABB SACE Emax 2 Bedienungsanleitung

ABB

ABB MNS-SG Bedienungsanleitung

ABB

ABB Smile 41 AS-i Series Bedienungsanleitung

ABB

ABB TPS44-H32 Bedienungsanleitung

ABB

ABB SACE Emax 2 Bedienungsanleitung

ABB

ABB EBN861 Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

S&C

S&C Vista SD Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Bedienungsanleitung