ABB ScreenMaster RVG200 Original Betriebsanleitung

Service instruction SI/RandC/001-EN

ScreenMaster RVG200

Paperless recorder

Terminal block failures

Measurement made easy

1Introduction

There have been instances reported where some or all inputs

on an RVG200 analog input card have shown as failed

immediately after installation, with no apparent cause for the

failure. In rare cases, this can be attributed to a faulty analog

input card but the most common cause has been identified as

a problem affecting the connection strips within the terminal

block assembly.

The reason for potential failure is that during installation,

unscrewing the terminal connection, inserting the wire and

tightening the screw can cause the spring assembly inside the

terminal block to move, breaking its contact with the PCB.

2Action

3 Tools required

— Medium, flat-bladed screwdriver

4 Identifying failures

1. Isolate the recorder from the power supply.

Referring to Fig. 4.1 (overleaf),

2. Press down into recess Aand pull terminal cover B

away from the case.

Continued...

Action when fault reported Action at next service

Information only Recall instruments

WARNING – Bodily injury

Isolate all power supplies to the recorder before removing

the terminal cover.

NOTICE – Property damage

The recorder is vulnerable to electrostatic damage.

Wear an anti-static strap or dismantle the unit on an

anti-static workbench.

SI/RandC/001-EN 10.2015

3. Insert a flat-bladed screwdriver into each slot Cin turn (2

slots) to release the locking arm and pull terminal block D

away from the case.

4. Check the position of spring contacts Ewithin the

terminal block assembly.

The correct position for the contacts is as shown in Fig. 4.1

– each contact must be positioned a minimum of halfway

across the slot in which the module board fits.

5. If a contact is positioned incorrectly or is damaged, replace

the terminal block assembly.

6. Fit the terminal block.

7. Refit terminal cover B.

Fig. 4.1 Examining the terminal block contacts

Note

We reserve the right to make technical changes or modify the contents of this

document without prior notice. With regard to purchase orders, the agreed

particulars shall prevail. ABB does not accept any responsibility whatsoever for

potential errors or possible lack of information in this document.

We reserve all rights in this document and in the subject matter and illustrations

contained therein. Any reproduction, disclosure to third parties or utilization of its

contents in whole or in parts – is forbidden without prior written consent of ABB.

ABB Limited

Process Automation

Howard Road

St. Neots

Cambridgeshire PE19 8EU

Tel: +44 (0)1480 475321

Fax: +44 (0)1480 217948

ABB Inc.

Process Automation

125 E. County Line Road

Warminster

PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

www.abb.com

Andere Handbücher für ScreenMaster RVG200

Andere ABB Messgerät Handbücher

ABB

ABB VA Master FAM540 Schulungshandbuch

ABB

ABB WaterMaster Bedienungsanleitung

ABB

ABB ODIN Bedienungsanleitung

ABB

ABB AMT-D1 Bedienungsanleitung

ABB

ABB XRC G5 Bedienungsanleitung

ABB

ABB Levelmeter 2000 Bedienungsanleitung

ABB

ABB ProcessMaster FEP630 series Bedienungsanleitung

ABB

ABB 10DX3111G Bedienungsanleitung

ABB

ABB SM1000 Bedienungsanleitung

ABB

ABB COMMANDER 1911 Bedienungsanleitung

ABB

ABB B23 Bedienungsanleitung

ABB

ABB Comem eOLI22 Bedienungsanleitung

ABB

ABB GLA232 Series Bedienungsanleitung

ABB

ABB ProcessMaster Installations- und Betriebshandbuch

ABB

ABB CM-UFD.M21 Beilage

ABB

ABB Sensyflow FMT700-P Bedienungsanleitung

ABB

ABB Gas Sampling Probe 2 Bedienungsanleitung

ABB

ABB GLA132 Series Bedienungsanleitung

ABB

ABB DATUM L150 Bedienungsanleitung

ABB

ABB SM500F Bedienungsanleitung

ABB

ABB Endura AZ20 series Bedienungsanleitung

ABB

ABB Sensyflow FMT500-IG Bedienungsanleitung

ABB

ABB AO2000-LS25 Bedienungsanleitung

ABB

ABB 4690 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung