ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

Contents

1. Safety Instruction................................................................................... 2

2. Technical Specifications ......................................................................... 3

3. The Unit Construction............................................................................ 6

4. Installation ............................................................................................. 6

5. Control Panel ......................................................................................... 7

6. Main Function........................................................................................ 8

7. How to Control the Unit....................................................................... 14

7.1 DMX Connection ............................................................................ 14

7.2 DMX Address Setting...................................................................... 15

7.3 DMX Configuration ........................................................................ 16

8. Troubleshooting ................................................................................... 17

9. Fixture Cleaning ................................................................................... 18

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Please read this instruction carefully which includes important

information about the installation, usage and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

◆Note: Use only the color gel that can resist high temperature. (

＞

300

℃

)

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the

unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit

when installing the fixture.

The equipment must be fixed by the professionals. And it must be fixed at a place where is out of

the touch of people and has no one pass by or under it.

2. Technical Specifications

DMX Control: 2 Channel Mode (Dimming, Strobe)

Control Modes: DMX, Master/Slave

Lens Options: 5°，11°，14°，19°，26°，36°，50°or 70°

0% ~ 100% linear dimming

Variable Strobe Effects

Input Voltage: AC 100 ~240V, 50/6 0 Hz

Power Consumption: 335W

Light Sources

：

1× 280W WW LED (E-300 WW)

1× 280W CW LED (E-300 CW)

CCT

：

3200K ± 100K

5600K ± 150K

IP Grade

：

IP22

WW CRI

：

Ra≧90

CW CRI

：

Ra≧85

Weight

：

°：

10.8kgs

°，

°：

10.6kgs

°，

°：

10.2kgs

Dimension

：

°：

1155 ×378 × 524mm

°，

°：

872 ×276 × 524mm

°，

°：

712 ×276 × 524mm

°，

°：

637 ×276 × 524mm

3. The Unit Construction

4. Installation

1 2

Loosen the two screws on the Main Body (MB) and put the Framing System into the MB, then

turn the Framing System right .Tighten the two screws to fix the Framing System.

1. Lens Module

；

2. Framing System

；

3. Bracket

；

4. Main Body;

5. Clip for Gel Holder

6. Gobo Slot

3 4

Put the Lens Module into the Framing System and tighten the Lens Module into the Framing

System with two screws.

5. Control Panel

．

Display: To show the various menus and the selected functions.

．

Dimmer Adjust Knob

：

Adjust the lightness for the unit；

．

LED:

MASTER On Master Mode

SLAVE On Slave Mode

DMX On DMX input present

4．MAINS OUT: PowerCon loop connection for main power supply to the next unit;

．

MAINS IN:PowerCon connection from main power supply;

．

DMX IN:For DMX512 link, use 5-pin XLR cable to link the unit and the DMX controller;

．

DMX IN:For DMX512 link, use 3-pin XLR cable to link the unit and the DMX controller；

．

DMX OUT: For DMX512 link, use 5-pin XLR cable to link the next unit and output DMX signal;

．

DMX OUT: For DMX512 link, use 3-pin XLR cable to link the next unit and output DMX signal;

10. RJ 45 Socket: No function at the moment. Reserve for Art-net in the future.

11. Fuse (T 6.3A): To protect the unit from damage of over current;

12. POWER SWITCH: Turns On/off the power;

13. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

6. Main Function

To select any functions, press the MENU button until the required function is showing on the

display. Select the function by pressing the ENTER button and the display will blink. Use the

DOWN and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup to go back to the functions without any changes press the MENU button

again. Hold and press the MENU button for one second or wait for one minute to exit the menu

mode.

The main functions are shown below:

1 ch

2D ch

2 ch

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME ARAS Bedienungsanleitung

ACME

ACME LED-MS150 Bedienungsanleitung

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME CEILING 40 Bedienungsanleitung

ACME

ACME Color Par 36 Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME E-10 WW DXX Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME Color Fusion CF-805 Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME CB-16FC Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME Dotline 360 Bedienungsanleitung

ACME

ACME E-200 MB MC Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung