ACME Color Par 36 Bedienungsanleitung

User Manual

Please read the instrucon carefully before use

CP-36S

Contents

1. Safety Instructions ................................................................................. 2

2. Technical Specifications ......................................................................... 3

3. How To Set The Unit............................................................................... 4

3.1 Control Panel ................................................................................... 4

3.2 Main Function.................................................................................. 5

4. How To Control The Unit...................................................................... 11

4.1 Master/Slave Built In Preprogrammed Function ............................ 11

4.2 DMX Controller .............................................................................. 11

5. DMX512 Configuration ........................................................................ 12

6. DMX Connection.................................................................................. 14

7. Troubleshooting ................................................................................... 15

8. Fixture Cleaning ................................................................................... 16

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit. DO NOT handle the unit by its head only, always carry by

its base.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Unit surface temperature may reach up to 75 degrees C. DO NOT touch the housing with

bare-hands during its operation. Turn off the power and allow about 15 minutes for the unit to

cool down before replacing or serving.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that

the unit is firmly fixed to avoid vibration and slipping while operating and make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the fixtures weight. Always use a safety cable that can hold 12 times of the weight of

the fixture when installing.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specifications

DMX Channels: 3/5/6 channels mode

3 operation modes: DMX, Master/Slave, and Sound Activation

Great built-in programs under master/slave operation triggered by music.

Optional easy controller CA-8 for instant lighting show

0 ~ 100% Smooth dimming and various strobe effects

Perfect for stage, theatre, TV studio, rental and discotheques

Input Voltage

：

AC 100~240V, 50/60Hz

Power Consumption

：

112W

LED Source

：

36 x 3W Tri-color LEDs

Beam Angle

：

24°

Weight

：

2.6kgs

Dimension

：

477 x 224 x 268mm

3. How To Set The Unit

3.1 Control Panel

1. Display: Shows the various menus and the selected functions.

2. Button:

6. MENU To select the programming functions

7. DOWN To go backward in the selected functions

8. UP To go forward in the selected functions

9. ENTER To confirm the selected functions

3. Mains input: Connects to power supply.

4. DMX output: DMX512 link, use 3-pin XLR cable to link the next unit.

5. DMX input: DMX512 link, use 3-pin XLR cable to link the unit and DMX controller.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required selection as

shown on the display. Select the function by the ENTER button and the display will blink. Use the

DOWN/UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Press and hold the MENU button for about one second or wait for one minute to exit the

menu mode.

The main functions are shown below:

（DMX 512 Address）

To select the , press the ENTER button to show the DMX ADDRESS on the display. Use the

DOWN/UP button to adjust the address from 1to 512. Once the address has been selected, press

the ENTER button to setup, to go back to the functions without any changes press the MENU

button again. Hold and press the MENU button for one second or wait for one minute to exit the

menu mode.

（

DMX Channel Mode）

To select the , press the ENTER button to show the DMX CHANNEL MODE on the display.

Use the DOWN/UP button to select the 3 CH, 5 CH or 6 CH mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any changes press

the MENU button again. Hold and press the MENU button for one second or wait for one minute

to exit the menu mode.

（Show Mode）

To select the , press the ENTER button to show the SHOW MODE on the display. Use the

DOWN/UP button to select the (Show 1), (Show 2), (Show 3) ,

(Show 4) （show 5）， (color) or (fade) mode，when you select color or fade

mode, press ENTER to confirm, use UP/DOWN button to select 1-10 or adjust fade speed (speed 1:

slow, speed 2: medium, speed 3: fast). Once the mode has been selected, press the ENTER button

to setup, to go back to the functions without any changes press the MENU button again. Hold and

press the MENU button for one second or wait for one minute to exit the menu mode.

（Slave Mode

）

To select the , press the ENTER button to show the SLAVE MODE on the display. Use the

DOWN/UP button to select the （master）, (normal) or (2 light show) mode.

Once the mode has been selected, press the ENTER button to setup, to go back to the functions

without any changes press the MENU button again. Hold and press the MENU button for one

second or wait for one minute to exit the menu mode.

（Dimmer Speed）

To select the , press the ENTER button to show the DIMMER SPEED on the display. Use

the DOWN/UP button to select the （smooth）or (fast) mode.Once the mode has

been selected, press the ENTER button to setup, to go back to the functions without any changes

press the MENU button again. Hold and press the MENU button for one second or wait for one

minute to exit the menu mode.

（Sound Mode）

To select the , press the ENTER button to show the SOUND MODE on the display. Use the

DOWN/UP button to select the (sound mode on) or (sound mode off). Once the

mode has been selected, press the ENTER button to setup, to go back to the functions without any

changes press the MENU button again. Hold and press the MENU button for one second or wait

for one minute to exit the menu mode.

（Sound Sense）

To select the , press the ENTER button to show the SOUND SENSE on the display. Use the

DOWN/UP button to adjust the sound sensitivity from 0to 100. Once selected, press the ENTER

button to setup, to go back to the functions without any changes press the MENU button again.

Hold and press the MENU button for one second or wait for one minute to exit the menu mode.

（DMX State）

To select the , press the ENTER button to show the DMX STATE on the display. Use the

DOWN/UP button to select the (master slave mode) or (blackout mode). Once the

mode has been selected, press the ENTER button to setup, to go back to the functions without any

changes press the MENU button again. Hold and press the MENU button for one second or wait

for one minute to exit the menu mode.

（LED Display）

To select the , press the ENTER button to show the LED DISPLAY on the display. Use the

DOWN/UP button to select the (LED display on) or (LED display off) mode. Once

the mode has been selected, press the ENTER button to setup, to go back to the functions without

any changes press the MENU button again. Hold and press the MENU button for one second or

wait for one minute to exit the menu mode.

（Display）

To select the , press the ENTER button to show the DISPLAY on the display. Use the

DOWN/UP button to select the (normal) or (display inversion). To go back to the

functions without any changes press the MENU button again. Hold and press the MENU button for

one second or wait for one minute to exit the menu mode:

Display normal mode for the fixture putting on the floor;

Display inversion mode for the fixture fixing under ceiling.

（White Balance）

To select the , press the ENTER button to show the DIMMER SPEED on the display. Use the

DOWN/UP button to select the （red）, （green）or (blue) mode.Once the

mode has been selected, press the ENTER button to setup, use UP/DOWN button to adjust the

value 125-255, to go back to the functions without any changes press the MENU button again.

Hold and press the MENU button for one second or wait for one minute to exit the menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME GLORY PROFILE Bedienungsanleitung

ACME

ACME 04XOZONE Bedienungsanleitung

ACME

ACME LP-F2000 VW Bedienungsanleitung

ACME

ACME UV-9N Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

ACME

ACME CEILING 40 Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME LED-RC8 Bedienungsanleitung

ACME

ACME MP-90 RGBW Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME XP-470 BSW Bedienungsanleitung

ACME

ACME SAM-50 Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME iColorLed 18TC Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME GENESIS COLOR II Bedienungsanleitung

ACME

ACME Dotline360 TB-1230 QW Bedienungsanleitung

ACME

ACME LED-MS50A Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME LED-MTX25 IP Bedienungsanleitung

ACME

ACME LED-256D RGB Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung