ACME FURY LED RGB Bedienungsanleitung

FURY LED RGB

RAGE LED RGB

LED-3082 RGB LED-3084 RGB

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Installation

4. How to set the unit

5. How to control the unit

6. DMX 512 Configuration

7. DMX 512 Connections

8. Troubleshooting

9. Fixture Cleaning

Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the fixture.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Disconnect main power before servicing and maintenance.

Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem, stop using the fixture immediately. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

Do not connect the device to any dimmer pack.

Do not touch any wire during operation and there might be a hazard of electric shock.

To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

The housing must be replaced if they are visibly damaged.

Do not look directly at the LED light beam while the fixture is on.

There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact your nearest dealer.

Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

For power supply, do not connect in series much more than 32 units, use

another mains supply for next 32 units.

2. Technical Specifications

Fitted with 2 x 3W tri-color LEDs, the DMX Fury/Rage LED fills the entire room with

powerful and laser-like muticolor beams, delivering fabulous effects.

Great built-in lighting shows under Master/Slave and SoundActive

Full range dimmer and variable strobe effects.

Optional CA-8 easy controller for enjoying instant lighting shows at you fingertips

LED display for easy navigation

Idear for discotheques, clubs, bars, parties, Mobile DJs, ect.

Input Voltage: AC100V~240V 50/60Hz

Power consumption: 16W

Fuse: T 6.3A

LED: 2 x 3W Tri-color LEDs 30000hrs rated

Dimension: 296 x 271 x 140mm

Weight: 4.0kgs (LED-3082 RGB)

3.8kgs (LED-3084 RGB)

3. Installation

The unit should be mounted via its screw

holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and

slipping while operating. Always ensure that

the structure to which you are attaching the

unit is secure and is able to support a weight

of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

4. How toset the unit

4.1Rear Panel

○

1Display: To show the various menus and the selected functions

LED:

○

2 DMX

DMX input present

○

3 MASTER

Master Mode

○

4 SLAVE

Slave Mode

○

5 SOUND

Flashing

Sound activation

Button:

○

6 MENU

To select the programming functions

○

7 DOWN

To go backward in the selected functions

○

8UP

To go forward in the selected functions

○

9 ENTER

To confirm the selected functions

○

10Microphone：Receive music for the sound active.

○

11 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.

○

12output：For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

○

13Only for remote control：By connect to the 1/4’’ microphone jack to control the unit for

Stand by, Function and Mode function.

○

14Safety Ring：For attached the safety cable.

○

15Mains output：Connect to supply mains power for the next unit.

○

16Mains input：Connect to supply mains power.

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to

setup or it will automatically return to the main functions without any change after idling 30

seconds. Back to the functions without any change press MENU button. The main functions

are shown below:

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup or automatically exit

menu mode without any change after 30 seconds. Back to the previous functions without

any change press MENU button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (1 channel) or (3

channels ) mode. Once select, press the ENTER button to setup or automatically exit menu

mode without any change after 30 seconds. To go back to the functions without any change

press the MENU button

Slave Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (master) or (slave 1) or

(Slave 2) mode. Once select, press the ENTER button to setup or automatically exit

menu mode without any change after 30 seconds. To go back to the functions without any

change press the MENU button

Show Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (Random show) or (show

1) or (Show 2) or … or (show8). Once select, press ENTER button to

store or automatically exit menu mode without any change after 30 seconds. To go back to

the functions without any change press the MENU button

Sound

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (sound on) or (sound off).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 30 seconds. To go back to the functions without any change press the MENU

button

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (blackout) or (normal).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 30 seconds. To go back to the functions without any change press the MENU

button.

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select (display on) or

(display off) mode. Once select, press ENTER button to setup or exit menu mode

without any change after 30 seconds. Back to the functions without any change press

MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to

select (normal) or (inverse), press ENTER button to setup. Back to the

functions without any change press MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run the built-in programmer for self-test. To go back to the functions

press the MENU button.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button.

Reset

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and all the motors will back to their home position.

4.3 Home Position Adjust

Press Enter button for about 5 seconds, “OPAN”will shown on the display, press ENTER

button to confirm, then use DOWN and UP button to adjust the home position (-127 - 127) of

the motor. Once the position has been selected, press the ENTER button to setup or exit the

offset mode without any change press the MENU button.

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show “L308”on the

display. After that the unit will be ready to receive DMX signal or run the built in programs.

5.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode and select

(random show), (show 1) or …or (show 8). Its DMX input jack will

have nothing plugged into it, and Its master LED will be constantly on and sound LED will

flash to the music. The other units will have to select (normal) or (2 light

show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the

slave led lights will constantly on.

2-light show

In slave mode, means the unit works as the master unit and means 2-light

show. In order to create a great light show, you can set on the second unit to get

contrast movement to each other, even if you have two units only.

5.2 Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By

connecting to the 1/4” microphone jack of the first unit, you will find that

the remote controller on the first unit will control all the other units for

Stand by, Function and Mode selection

5.3 DMX Controller

Using universal DMX controller to control the units, you have to set DMX address from 1 to

512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when

the display stops blinking or storing automatically 8 seconds later. To go back to the

functions without any change press the MENU button again. If you use please refer to the

following diagram to address your DMX512 channel for the first 4 /2 units.

1 channel mode:

3 channels mode:

Blackout

Blackout the unit

Function

1. SynchroStrobe

2. Asynchro Strobe

3. Sound Strobe

Select Show

(Show 1-8)

Select Speed

1. Slow

2. Middle

3. Fast

Mode

Sound/Strobe

(LED OFF)

Show

(LED ON)

LED blinking

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME Color Fusion CF-805 Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME Stage Panel 1080 Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME UV-9N Bedienungsanleitung

ACME

ACME Theatre LED Colour Flood Bedienungsanleitung

ACME

ACME Eventx 100 Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME Genesis move 25R Bedienungsanleitung

ACME

ACME Junior Series Bedienungsanleitung

ACME

ACME LP-F2000 VW Bedienungsanleitung

ACME

ACME MH-600A Mobile Color Bedienungsanleitung

ACME

ACME LED-MS150 Bedienungsanleitung

ACME

ACME Color Spot Bedienungsanleitung

ACME

ACME Color Par 36 Bedienungsanleitung

ACME

ACME SAM-50 Bedienungsanleitung

ACME

ACME THUNDERBOLT Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung