ACME LS-608 RGB Bedienungsanleitung

Laser Bar RGB

LS-608 RGB

User Manual

Please read the instructions carefully before use

1. Safety Instructions............................................................................................................................2

2. Technical Specifications....................................................................................................................3

3. Installation ........................................................................................................................................3

4. How to set the fixture.......................................................................................................................4

4.1 Control Panel ..................................................................................................................................4

4.2 Main Functions...............................................................................................................................4

5. How To Control The Fixture..............................................................................................................8

6. DMX512 Configuration .....................................................................................................................8

7. Troubleshooting..............................................................................................................................10

8. Fixture Cleaning..............................................................................................................................11

1. Safety Instructions

WARNING

Laser radiation avoids body exposure, especially for eye, it’s easy to cause blindness. Please keep the

safe distance at 30 meters from clothing or skin.

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Disconnect main power before replacement or servicing.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature is

higher than this.

Unit surface temperature may reach up to 85 degrees C. DO NOT touch the housing with bare-hands

during its operation.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

DO NOT connect any dimmer.

DO NOT touch any cables during operation as high voltage may cause electric shock.

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

2. Technical Specifications

DMX Control;

Input Voltage: AC100V~240V，50/60Hz

Power Consumption of Laser: 800 mW x 6

Power Consumption 105W

IP Rate IP X4

Dimension: 915 x 225.5 x 249mm

Weight: 13.8Kgs

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed

to avoid vibration and slipping while operating and make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight. Always use

a safety cable that can hold 12 times of the weight of the fixture when installing.

The equipment must be installed by professionals and it must be installed in a place where is out of the

reach of people and no one can pass by or under it. The unit must be installed 0 ~ 30 meters from

adjacent surfaces.

4. How to set the fixture

4.1 Control Panel

○

1 Power Input /Output ○

2DMX IN/OUT

○

3 Key switch ○

4 LED Indicator

○

5 Display ○

6Menu

4.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display. Select the

function by the ENTER button and the display will blink. Use the DOWN/UP button to change the mode.

Once the required mode has been selected, press the ENTER button to setup or it will automatically

return to the main functions without any change after idling one minute. Back to the functions without

any change press the MENU button.

DMX Address

Select the DMX Address, press the ENTER button and the display will blink. Use the DOWN/UP button to

change the DMX 512 address. Once the address has been selected, press the ENTER button to save or

automatically exit menu mode without any change after one minute. Back to the previous functions

without any change press the MENU button.

Channel mode

Select the Channel Mode, press the ENTER button and the display will blink. Use the DOWN/UP button

to select the 5CH/20CH. Once select the required mode, press the ENTER button to save or automatically

exit menu mode without any change after one minute. To go back to the functions without any change

press the MENU button.

DMX Last State

Select the DMX Last State (The state when the fixture out of signal), press the ENTER button and the

display will blink. Use the DOWN/UP button to select Blackout (Blackout the output) or Hold (Hold the

last state). Once select the required mode, press the ENTER button to save or automatically exit menu

mode without any change after one minute. To go back to the functions without any change press the

MENU button.

Starting Value

Select the Starting Value, press the ENTER button and the display will blink. Use the DOWN/UP button to

select Red/Green/Blue and set the value of six lasers for Red1-Red6/Green1- Green6/Blue1- Blue from

000 to 125. Once select the required mode, press the ENTER button to save or automatically exit menu

mode without any change after one minute. To go back to the functions without any change press the

MENU button.

White Balance

Select the White Balance, press the ENTER button and the display will blink. Use the DOWN/UP button

to select Red /Green/ Blue/ Red1-Red6/Green1- Green6/Blue1- Blue6 and set the value from 90 to 255.

Once select the required mode, press the ENTER button to save or automatically exit menu mode

without any change after one minute. To go back to the functions without any change press the MENU

button.

Control Direction

Select the Control Direction press the ENTER button and the display will blink. Use the DOWN/UP button

to select Right to Left or Left to Right. Once select the required mode, press the ENTER button to save or

automatically exit menu mode without any change after one minute. To go back to the functions without

any change press the MENU button.

Auto Test

Select the Back Light, press the ENTER button. The fixture will test by itself automatically. Back to the

functions without any change press MENU button again.

Manual Test

Select the Manual Test, press the ENTER button and the display will blink. Use the DOWN/UP button to

select Red /Green/ Blue/ /Dimmer/Effect Red1-Red6/Green1- G r e e n 6/ Blue1- Blue6 and set the value

from 000 to 255. Once select the required mode, press the ENTER button to save or automatically exit

menu mode without any change after one minute. To go back to the functions without any change press

the MENU button.

Temperature

Select the Temperature, press the ENTER button and the display will show the current running

temperature of the fixture. To go back to the functions press the MENU button again.

Fixture Hours

Select the Fixture Hours, press the ENTER button and the display will show the running time of the

fixture. To go back to the functions press the MENU button.

Software Version

Select the Software Version, press the ENTER button and the display will show the version of software of

the fixture. To go back to the functions press the MENU button again.

5. How To Control The Fixture

1. Control by DMX Console；

Use universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so

that the units can receive DMX signal.

6. DMX512 Configuration

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME PAGEANT 300ZR II Bedienungsanleitung

ACME

ACME CEILING 40 Bedienungsanleitung

ACME

ACME PAGEANT 300ZR Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME LED-BL4B Bedienungsanleitung

ACME

ACME LED-BR10 Bedienungsanleitung

ACME

ACME BLINDER LINE 10 IP Bedienungsanleitung

ACME

ACME GLORY PROFILE Bedienungsanleitung

ACME

ACME LED-920D Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME Dotline360 TB-1230 QW Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME LED-256D RGB Bedienungsanleitung

ACME

ACME MINI ELLIPSOIDAL 10 Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung