ACME LED-ST2000 Bedienungsanleitung

MEGA STROBE

LED-ST2000

User Manual

Please read the user manual before use

Table of Contents

1，Safety Information…………………………………………………. 3

2，Rear Panel…………………………………………………………. 5

3，Preparation for Use ………………………………………………...5

4，Main Function …………………………………………………….. 6

5，Remote Control…………………………………………………….10

6，Technical Specification…………………………………………….13

1. Safety Information

Warning: This product is for professional use only! It is not for

household use.

The LED-ST2000 presents risks of lethal or severe injury due to fire and

heat, electric shock, ultraviolet radiation, and falls. Flashing light is also

known to trigger epileptic seizures in persons who are photosensitive.

Read this manual before powering or installing the fixture, follow the

safety precautions listed below and observe all warnings in this manual

and printed on the fixture.

Noted: high voltage in the LED board!

Super power strobes, so please avoid extended periods of

continuous flashing

To guard against electric shock

Do not remove the rear cover: there are no user-serviceable parts inside.

Always ground (earth) the fixture electrically.

Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

Do not expose the fixture to rain or moisture.

To guard against UV radiation, burns, and fire

Never operate the fixture with the front glass open, missing or damaged.

Do not stare directly into the light. Never look at an exposed LED while it is lit.

Never attempt to bypass the fuse. Always replace defective fuses with ones of the

specified type and rating.

Verify that the power feed cable is rated for the current draw of all connected

fixtures.

Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters

(20 inches) away from the fixture. Keep flammable materials well away from the

fixture.

Minimum distance to illuminated surface is 10 meters.

Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

Never place filters or other materials over the front glass cover.

The exterior of the fixture can reach temperatures up to 120° C (248° F). Allow the

fixture to cool for at least 15 minutes before handling.

Do not modify the fixture or install other than genuine parts.

Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104°

F).

To guard against falls

When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

Block access below the work area whenever installing or removing the fixture.

To guard against epileptic seizure

Do not operate the fixture near stairways.

Provide advance notice that strobe lighting is in use.

Avoid extended periods of continuous flashing, particularly at frequencies of 10 to

20 flashes per second.

2. Rear Panel

1, Fuse Holder

2, Main Power

3. LED display

4, Menu /UP/DOWN/ Enter button

5, DMX signal/ Flash indicator

6, DMX input/output

3. Preparation for Use

Table1: Cord cap wirings

INSTALLATION

The LED-ST2000 may be installed in any orientation. The mounting bracket provides

five 12 mm holes for direct fastening or attachment of rigging clamps.

To install the mounting bracket

1. Place the fixture face down on a table.

2. Place an aluminum washer on each mounting bracket stud.

3. Make clear the direction of left and right side of bracket and lock the screws. After

that, tighten one hand knob to lock the mounting bracket in one end of bracket.

4. MAIN FUNCTION

Press MENU button enter the function, then use UP/DOWN or MENU button

to select the function you want, final press ENTER button to confirm the

function you select. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second. The

main menu as follow:

4.1 DMX 512 address setting

Select ADDR option and the display will blink, press ENTER button to

confirm your selection. You can check the current DMX address from LED

display. The DMX address can be changed by press UP/DOWN button and

then press ENTER button to confirm your selection. Wait for 30 seconds, it

will return to main interface. If you want back to main menu, please hold

MENU button for 1 second.

4.2 Channel mode setting

Select CHMD option, press ENTER button to confirm your selection. Change

the channel way (1/2/3/4) by press UP/DOWN button. Press ENTER button

to confirm your selection. Wait for 30 seconds, it will return to main interface.

If you want back to main menu, please press MENU button.

4.3 LED display setting

Select the LED option, press ENTER button to confirm your selection. You

can see the current ON/OFF status of LED display now. You can change its

status by press UP/DOWN button. Then press ENTER button to confirm your

selection. If you choose OFF, than the LED display will close without any

operation for I min. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

4.4 LED display direction setting

Select DISP option, press ENTER button to confirm your selection. Select

the DISP / DSIP by press UP/DOWN button. Press ENTER button to confirm

your selection. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

4.5 Test setting

Select TEST option, press ENTER button to confirm your selection. The

flash indicator will light up and the unit will test automatically. Wait for

several seconds self-test, it will return to main interface. If you want back to

main menu, please hold MENU button for 1 second.

4.6 Temperature

Select the LEMP, press ENTER button and the display will show the

temperature of unit. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second.

4.7 Check the version number

Select the VER, press ENTER button to confirm. You can see the current

version number now (b 10/v 10) and check them by UP/DOWN. Wait for 30

seconds, it will return to main interface. If you want back to main menu,

please hold MENU button for 1 second.

Channel Mode:

DMX CONTROL SUMMARY

Intensity

Flash intensity can be set from minimum (blackout) to maximum on 1-channel DMX

modes, channel 2 in 2-channel DMX modes and channel 1 in the 3- and 4-channel

DMX modes.

The maximum intensity can be reduced by selecting low power mode as described

Duration

Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530 ms

on 60 Hz power supplies, on channel 2 in the 3- and 4-channel DMX modes. Flash

duration is fixed in 1 channel DMX mode.

Rate

Flash rate can be set from 0 flashes per second to 17.5 flashes per second Hz on 50

Hz power supplies or from 0 to 20 flashes per second on 60 Hz power supplies, on

channel 3 in the 3- and 4-channel DMX modes. Flash rate is also controllable in 1-

and 2-channel DMX mode.

Built-in effects

Six programmed effects are available on channel 4 in the 4-channel DMX mode

only. The effects may be altered using the intensity, duration, and rate controls.

Inhaltsverzeichnis

Andere ACME Scheinwerfer Handbücher

ACME

ACME TV PANEL200 Bedienungsanleitung

ACME

ACME LED-CTL6 Bedienungsanleitung

ACME

ACME LP-900 Bedienungsanleitung

ACME

ACME CM-108 RGB Bedienungsanleitung

ACME

ACME LED-ST50 Bedienungsanleitung

ACME

ACME theatre spot 150 TS-150 CW Bedienungsanleitung

ACME

ACME REFracted RLS 100 Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME LED-7474 Bedienungsanleitung

ACME

ACME DMX 512 Bedienungsanleitung

ACME

ACME SUPER NOVA RGB Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME TV PANEL100 Bedienungsanleitung

ACME

ACME BARRAGE LED-247 Bedienungsanleitung

ACME

ACME Dragonfly Bedienungsanleitung

ACME

ACME XPerior 700WZA Bedienungsanleitung

ACME

ACME BW-545 Bedienungsanleitung

ACME

ACME Invincibled LED-767RGBWII Bedienungsanleitung

ACME

ACME MEGA STROBE 5000 RGB Bedienungsanleitung

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Bedienungsanleitung

ACME

ACME TS-300M CW Bedienungsanleitung

ACME

ACME Dynamic 25 Spin LED?GF25 Bedienungsanleitung

ACME

ACME LED-192RGB Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung