ACME TS-300M CW Bedienungsanleitung

TS-300M CW

TS-300M WW

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instructions ................................................................................. 2

2. Technical Specifications ......................................................................... 3

3. The Plate for Color Filter & Barn Door Installation................................. 4

4. How To Set The Unit............................................................................... 5

4.1 Control panel ................................................................................... 5

4.2 Main Functions ................................................................................ 6

5. How to Control the Unit....................................................................... 11

5.1 Master/Slave Built In Preprogrammed Function ............................ 11

5.2 DMX Controller .............................................................................. 11

5.3 DMX 512 Configurations ................................................................ 12

6. DMX 512 Connections ......................................................................... 12

7. Troubleshooting ................................................................................... 13

8. Fixture Cleaning ................................................................................... 14

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specifications

◆Manual linear dimming zoom range: 15°~ 53°

◆DMX, Master/Slave, Manual, Art-Net

◆4 dimming curves, 2 optional dimmer speed

◆0~100% smooth dimming

◆Low noise under 35db@1m

◆Rotating barn door and hanger

Power supply: AC 100~240V, 50/60Hz

Power consumption: 320W

Color Temperature: 5500+200K (TS-300 CW)

3200+200K (TS-300 WW)

Light Source: 1 × 300W white LED

CRI: WW ≥95

CW ≥95

WW: ≥95

CW: ≥95

Weight: 10 Kgs

Dimension: 340×583×284mm

583 340

284

3. The Plate for Color Filter & Barn Door Installation

Fig. 1

At first, please push the Lock Cap button by hand as the arrow ○

1E A, and move away the Lock as the

arrow A○

2E A; Then insert the Plate for Color Filter into the inside slot from topsideA○

3E A;

Fig. 2

Secondly, please insert the Barn Door into the outside slot from topside as arrow A○

4E A, and fasten

the lock (Note: the Barn Door must be fastened into the inside of the lock’s hook ); then flip down

the lock cap again as arrowA○

5E A.

4. How To Set The Unit

4.1 Control panel

8910

711

1. Display: Show the various menus and the selected functions.

2. LED:

MASTER On Master Mode

SLAVE On Slave Mode

DMX On DMX input present

3. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

4. Dimmer: Manual adjust the dimmer value.

5 Zoom: Manual adjust the zoom value.

6. DMX input: For DMX512 link, use 5-pin XLR cable to link the unit together.

7. POWER IN: Connects to mains supply power.

8. POWER OUT: Connects to the next unit.

9. DMX output: For DMX512 link, use 5-pin XLR cable to link the unit together.

10. Fuse(T10A): Used to protect the unit from damage of the over current.

11.ETHERNET: Connect with the multimedia and use software to control the units via ArtNet;.

4.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use the DOWN and UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup or

it will automatically return to the main functions without any change after idling one minute. Back

to the functions without any change press the MENU button.

The main functions are shown below:

DMX Address

Select DMX Address, press the ENTER button to confirm, the present address will blink on the

display. Use the UP and DOWN button to adjust the DMX address from 1to 512. Once the address

has been selected, press the ENTER button to save. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Are-Net Setup

To select Are-Net Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or Art-Net Port Setup, press the ENTER button to store. When choose Ethernet

IP Setup, use the UP/DOWN button to select IP Address or Subnet Mask.When choose Art-Net

Port Setup, use the UP/DOWN button to select Net, Subnet or Universe. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

1CH or 2CH channels mode, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode.

Dimmer Speed

Select Dimmer Speed, press the ENTER button to confirm, present mode will blink on the display.

Use the DOWN and UP button to select the Smooth (dimmer speed smooth) or Fast(dimmer

speed fast) mode. Once the mode has been selected, press the ENTER button to save. Hold and

press the MENU button about one second or wait for one minute to exit the menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display, use

the UP/DOWN button to select Mode 1,Mode 2,Mode 3 or Mode 4. Once selected, press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

Linear: The increase in light intensity appears to be linear as DMX value is increased.

S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Slave Mode

Select Slave Mode, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to select the Master or Slave mode. Once the mode has been selected,

press the ENTER button to save. Hold and press the MENU button about one second or wait for

one minute to exit the menu mode.

DMX State

Select DMX State, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to select the Master Slave, Blackout or Hold mode. Once the mode has

been selected, press the ENTER button to save. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Display Settings

Enter menu mode, select Display Settings, press ENTER button to confirm, use UP/DOWN button

to select Contrast Ratio, Backlight Auto Off, Invert Display or Language.

Contrast Ratio

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Scheinwerfer Handbücher

ACME

ACME LED-4TC Bedienungsanleitung

ACME

ACME Dynamic 25 Spin LED?GF25 Bedienungsanleitung

ACME

ACME theatre spot 150 TS-150 CW Bedienungsanleitung

ACME

ACME LED-7474 Bedienungsanleitung

ACME

ACME BARRAGE LED-248 Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME CB-348TC Bedienungsanleitung

ACME

ACME TV PANEL100 Bedienungsanleitung

ACME

ACME Super Splash Bedienungsanleitung

ACME

ACME SUPER NOVA RGB Bedienungsanleitung

ACME

ACME Butterfly quard Bedienungsanleitung

ACME

ACME DMX 512 Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME BW-545 Bedienungsanleitung

ACME

ACME Invincibled LED-767RGBWII Bedienungsanleitung

ACME

ACME MEGA STROBE 5000 RGB Bedienungsanleitung

ACME

ACME REFracted RLS 100 Bedienungsanleitung

ACME

ACME Dragonfly Bedienungsanleitung

ACME

ACME LED-ST50 Bedienungsanleitung

ACME

ACME LED-ST2000 Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME CM-108 RGB Bedienungsanleitung

ACME

ACME PAGEANT CM-600z Bedienungsanleitung

ACME

ACME LED-CTL6 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung