ACME LP-900 Bedienungsanleitung

TV LIGHT PANEL 900

LP-900

UserManual

Please read the instructions carefully before use

CONTENTS

1. Safety Introductions..................................................................................................2

2. Technical Specifications............................................................................................3

3. Installation.................................................................................................................3

4. How To Set The Fixture ............................................................................................3

4.1 Control Panel ......................................................................................................3

4.2 Main Function......................................................................................................4

5. How To Control The Unit...........................................................................................7

5.1 Master/Slave Function ........................................................................................7

5.2 DMX Controller....................................................................................................7

6. DMX512 Configuration .............................................................................................8

7. DMX512 Connections...............................................................................................8

8. Troubleshooting........................................................................................................9

9. Fixture Cleaning......................................................................................................10

1. Safety Introductions

WARNING

yPlease keep this User Manual for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

yThe unit is for indoor use only and use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

yDisconnect mains power before fuse replacement or servicing.

yReplace fuse only with the same type.

yMake sure there are not flammable materials close to the unit while operating as it is fire hazard.

yUse safety cable when fixes this unit.

yMaximum ambient temperature is TA: 40℃and don’t operate it where the temperature is higher

than this.

yThere are no user serviceable parts inside the fixture. Do not open the housing or attempt any

repairs by yourself. In the unlikely event your fixture may require service, please contact the nearest

authorized technical assistance center and always use the same type spare parts. .

yDon’t connect the device to any dimmer pack or power pack.

yDo not look directly at the LED light beam while the fixture is on.

yDo not touch any wire during operation as high voltage might be causing electric shock.

yDue to the magnifying type lens, please keep the lens out of contact with direct sunlight. Direct

sunlight can cause heat to build up inside of the unit, which will seriously damage unit.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

For power supply, do not connect in series much more than 4 units, use

another mains supply for next 4 units.

2. Technical Specifications

yIt can be operated by DMX512 control or can be used as an individual unit without controller.

yIt can be linked together as many as required in master/slave mode, and perform the great built-in

programmed lighting shows triggered by music.

yPlease use a 3 pin XLR cable/plug when connecting them together.

yIt features different pre-programmed chase patterns.

y3 Channel modes.

yVoltage：AC 100V-240V~ 50/60Hz

yLED: Total 900pcs,

CW: 450pcs,

WW: 450pcs

yPower consumption: 76W

yFuse: T6.3A

yDimension: 356 x 328 x 111mm

yWeight: 5.6KG

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed

to avoid vibration and slipping while operating. Always ensure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight.Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch

of people and has no one pass by or under it.

4. How To Set The Fixture

4.1 Control Panel

○

1Display: To show the various menus and the selected functions

○

2 Indicator LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

COLOR

TEMP. Flashing Max. power consumption of

CW/WW

○

3 Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

○

4 Color Adjust knob: Adjust the color temperature from 3200k to 6500k, 25K as a step. When the

value is between 4825K and 4875K the green LED indicator will light .It

means the power consumption of CW/WW color the has reached maximum.

○

5 Dimmer Adjust knob: Adjust lightness for the unit.

○

6 DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

○

7 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

○

8 Mains output: Connect to supply mains power for the next unit.

○

9 Mains input: Connect to supply mains power.

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display. Select the

function by ENTER button and the display will blink. Use DOWN and UP button to change the mode.

Once the required mode has been selected, press ENTER button to setup or it will automatically return

to the main functions without any change after idling 30 seconds. Back to the functions without any

change press MENU button. The main functions are shown below:

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address has

been selected, press ENTER button to setup or automatically exit menu mode without any change after

30 seconds. Back to the previous functions without any change press MENU button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select the (2 channels) or (2

channels) or (3 Channels) mode. Once the mode has been selected, press the ENTER button to

setup or automatically exit menu mode without any change after 30 seconds. To go back to the functions

without any change press the MENU button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select the or or (dimmer)

mode, press the ENTER button to confirm, use UP and DOWN button to adjust the value between 0 and

255, once select press ENTER button to setup or automatically exit menu mode without any change

after 30 seconds. To go back to the functions without any change press the MENU button.

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER button, Use

DOWN and UP button to select the (blackout) or (normal). Once select, press ENTER

button to setup or automatically exit menu mode without any change after 30 seconds. To go back to the

functions without any change press the MENU button

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select (display on) or (display off)

mode. Once select, press ENTER button to setup or exit menu mode without any change after 30

seconds. Back to the functions without any change press MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to select

(normal) or (inverse), press ENTER button to setup. Back to the functions without any change

press MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER button and

the unit will run the built-in programmer for self-test. To go back to the functions press the MENU button.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER button and

the display will show the number of working hours of the unit. To go back to the functions press the

MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER button and

the display will show the version of software of the unit. To go back to the functions press the MENU

button again.

5. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave function

2. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address setting will be

effected at once. Every time you turn the unit on, it will show type on the display. After that the unit will be

ready to receive DMX signal or run the built in programs.

5.1 Master/Slave Function

By linking the units in master/slave connection, the first unit will be master automatically. You should set

the master unit effect via its knobs, then the other units (slave) will lighting as the same.

5.2 DMX Controller

An universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so

that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has

been selected, press and keep ENTER button pressed up to when the display stops blinking or storing

automatically 30 seconds later. To go back to the functions without any change press the MENU button

again.

If you use please refer to the following diagram to address your DMX512 channel for the first 4 units.

2 channels:

3 channels:

6. DMX512 Configuration

2/2/3 Channels Mode:

7. DMX512 Connections

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the

input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or

damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down

the system

2. The DMX output and input connectors are pass-through to maintain the DMX circuit when one of the

units’ power is disconnected.

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal errors. Solder

a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in

the DMX-output of the last fixture.

4. Each lighting fixture needs to have an address set to receive the data sent by the controller. The

address number is between 0-511 (usually 0 & 1 are equal to 1).

5. 3 pin XLR connectors are more popular than 5 pins XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),

Pin4/5: not used

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are some suggestions for

easy troubleshooting:

A. The fixture does not work, no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and DMX

polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture

or the previous one.

4. Try to use another DMX controller.

Inhaltsverzeichnis

Andere ACME Scheinwerfer Handbücher

ACME

ACME TS-300M CW Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME REFracted RLS 100 Bedienungsanleitung

ACME

ACME BARRAGE LED-247 Bedienungsanleitung

ACME

ACME DMX 512 Bedienungsanleitung

ACME

ACME LED-192RGB Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME TV PANEL100 Bedienungsanleitung

ACME

ACME PAGEANT CM-600z Bedienungsanleitung

ACME

ACME theatre spot 150 TS-150 CW Bedienungsanleitung

ACME

ACME XPerior 700WZA Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME MEGA STROBE 5000 RGB Bedienungsanleitung

ACME

ACME Invincibled LED-767RGBWII Bedienungsanleitung

ACME

ACME TV PANEL200 Bedienungsanleitung

ACME

ACME LED-7474 Bedienungsanleitung

ACME

ACME LED-4TC Bedienungsanleitung

ACME

ACME CP?64 BD15 Bedienungsanleitung

ACME

ACME LED-CTL6 Bedienungsanleitung

ACME

ACME MEGA STROBE 5000 Bedienungsanleitung

ACME

ACME LED-ST2000 Bedienungsanleitung

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Bedienungsanleitung

ACME

ACME Butterfly quard Bedienungsanleitung

ACME

ACME BW-545 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung