ACR Electronics OLAS CORE Betriebsanleitung

Alert Settings

(Guardian/Core)

Sound

Siren (Default)

Volume

Alert Delay

seconds

Connected to

(Guardian only)

Pause Alert Sound

0438

Far

MOB

1. Accept the alarm with the ACR OLAS App.

Troubleshooting

2. Bring the Tag within 1 meter of the Core.

3. Cancel the alarm on the Core by pressing the control

switch once. After 10 seconds the system will be

tracking again.

4. Navigate to the Alert Settings in the ACR OLAS App.

5. Adjust the Alert Delay to 6 seconds. This means if the

connection between the Tag and the Core is broken for

longer than 6 seconds the alarm will sound.

6. Walk to the location where the Tag previously set off

the alarm and then continue walking around the vessel.

If you experience a false alarm whilst testing the system, it is likely because the connection between the Tag and

the Core was broken for longer than 3 seconds. If this occurs carry out the following steps to adjust your system.

10s

Alert Settings

Sound

Siren (Default)

Volume

Alert Delay

seconds

Connected to

(Guardian only)

Pause Alert Sound

0438

Far

MOB

Tutorials

Online

Solo Mode

Vessel

Information

Alert Settings

Device Selection

FAQ’s

Close OLAS

Firmware Update

0438

Near

MOB

Press and hold the MOB button

on your GPS Chart Plotter

Send a MOB DSC alert

using your VHF

Tom

Overboard!

Step 1

Step 2

Continue to recovery

www.acrolas.com

Troubleshooting

9. If a false alarm sounds again return to step 1 and increase the Alert Delay at step 5 in increments of 3 seconds.

If false alarms continue after 15 seconds the Core should be moved closer to the point at which the alarm is

being triggered, or an additional OLAS Extender is required to cover the signal ‘black spot’.

Alert Settings

(Guardian/Core)

Sound

Siren (Default)

Volume

Alert Delay

seconds

Connected to

(Guardian only)

Pause Alert Sound

Alert Settings

(Guardian/Core)

Sound

Siren (Default)

Volume

Alert Delay

seconds

Connected to

(Guardianonly)

Pause Alert Sound

0438

Far

MOB

Tutorials

Online

Solo Mode

Vessel

Information

Alert Settings

Device Selection

FAQ’ s

Close OLAS

Firmware Update

0438

Near

MOB

Press and hold the MOB button

on your GPS Chart Plotter

Send a MOB DSC alert

using your VHF

Tom

Overboard!

Step 1

Step 2

Continue to recovery

www.acrolas.com

1m1m

7. You should always try to install your Core at least 0.5

meters from any equipment transmitting radio signals

including VHF Radios, antennas and cables.

8. If located within 0.5 meters it is possible false alarms may occur. If you

are experiencing false alarms try moving the Core hub away from

other electrical devices and then carry out the Core setup and range

test to see if the false alarms still occur.

Andere Handbücher für OLAS CORE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACR Electronics Zubehör Handbücher

ACR Electronics

ACR Electronics OLAS CORE Bedienungsanleitung

ACR Electronics

ACR Electronics FPR-10 PROGRAMMER Montageanleitung

ACR Electronics

ACR Electronics FPR-20 PROGRAMMER Montageanleitung

ACR Electronics

ACR Electronics 406 EPIRB, NOAA Bedienungsanleitung

ACR Electronics

ACR Electronics OLAS CORE Bedienungsanleitung

ACR Electronics

ACR Electronics FPR-100 PROGRAMMER Montageanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung