ACU-RITE 01607BPDI Bedienungsanleitung

Instruction Manual

Weather Center

model 01607BPDI

Questions? Contact Customer Support at

(877) 221-1252 or visit www.AcuRite.com.

CONTENTS

Unpacking Instructions................2

Package Contents.......................2

Product Registration....................2

Features & Beneﬁts: 3-in-1 ..........3

Features & Beneﬁts: Display .......4

Setup ........................................6

3-in-1 Sensor Setup....................6

Display Unit Setup......................7

Intelli-Time®Clock ......................8

Set Time, Date & Units ................8

Backlight Settings .......................8

Placement Guidelines .................9

3-in-1 Sensor Installation ..........10

Using the Weather Center.........11

Troubleshooting........................13

Care & Maintenance ................15

Calibration ..............................15

Replace Intelli-Time®Battery......16

Speciﬁcations...........................17

FCC Information.......................17

Customer Support ....................18

Warranty.................................18

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Archive~ Products

Congratulations on your new AcuRite product. To ensure the best

possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective ﬁlm that is applied to the LCD screen prior to using this

product. Locate the tab and peel off to remove.

Package Contents

1. Display unit

2. 3-in-1 sensor

3. Sensor mounting bracket

4. Mounting hardware

5. Power adapter

6. Instruction Manual

IMPORTANT PRODUCT MUST BE REGISTERED

TO RECEIVE WARRANTY SERVICE

PRODUCT REGISTRATION

to receive 1 year

warranty protection

www.AcuRite.com

►

Features & Benets

3-in-1 SENSOR

1. Temperature & Humidity Sensors

(internal)

2. Release Lever for Battery Access

3. Mounting Point

4. Wind Speed Anemometer

5. Mounting Hardware

Includes anchors and screws.

Qty Diameter Length

4 #4 1”

1 #6 or #8 1/4” or 3/8”

6. Mounting Bracket

7. A-B-C Switch (not shown)

ID code that must match display’s

A-B-C switch to ensure units

synchronize.

Features & Benets

1 2 3 4

10 91113 12

242627

DISPLAY UNIT FRONT

1. Average Wind Speed

Based on all wind speed readings

from the past 2 minutes.

2. Current Wind Speed

3. Backlight Button

For momentary backlight and

dimmer settings.

4. Peak Wind Speed

Highest speed from past 60 minutes.

5. Current Indoor Temperature

Arrow icon indicates the direction the

temperature is trending.

6. Current Indoor Humidity

Arrow icon indicates the direction

the humidity is trending.

7. Barometric Pressure

Arrow icon indicates the direction

the pressure is trending.

8. Humidity Level Indicator

Indicates a high, low or ideal indoor

humidity level.

9. Display Low Battery Indicator

10. Date

11. Intelli-Time®Clock

Automatically updates itself for

Daylight Saving Time.

12. AUTO DIM Indicator

Indicates display backlight “AUTO

DIM” mode activated.

13. Moon Phase

14. Sensor Low Battery Indicator

15. Seasonal Information

Wind chill will show when temperatures

are below 40oF (4oC), Dew Point when

temperature is 41-79oF (5-26oC), and

Heat Index when temperature is over

80oF (27oC).

16. Learning Mode Icon

Disappears after weather forecast

self-calibration is complete.

17. 12 to 24 Hour Weather Forecast

Self-Calibrating Forecasting pulls data

from your sensor to generate your

personal forecast.

18. Current Outdoor Humidity

Arrow icon indicates the direction

the humidity is trending.

19. Outdoor Sensor Signal Strength

20. Current Outdoor Temperature

Arrow icon indicates the direction the

temperature is trending.

DISPLAY UNIT BACK

21. Integrated Hang Hole

for easy wall mounting.

22. A-B-C Switch

ID code that must match sensor’s A-B-C

switch to ensure units synchronize.

23. Plug-in for Power Adapter

24. Reset Button

Full reset to factory defaults.

25. Power Adapter

26. Intelli-Time®Battery Compartment

27. Battery Compartment

28. Button

for setup preferences.

29. Button

for setup preferences.

30. Button

for setup preferences.

31. Button

Press to access all-time high and

low records.

32. Battery Compartment Cover

(not shown)

•

• Install Batteries

V 4 AA batteries

sWf~~~"It(•P

#1-f

■

__a_ooc:_>_1_5=--8-=---

0-=-F_JI

ALKALINE

BATTERIES [TOOC)

158°F I

SETUP

3-IN-1 Sensor Setup

Set the A-B-C Switch

The A-B-C switch is located inside

the battery compartment. It can be

set to A, B or C. However, you must

select the same letter choices for

both the sensor and the display unit

in order for the units to synchronize.

Install or Replace Batteries

AcuRite recommends high quality

alkaline or lithium batteries for the

best product performance. Heavy

duty or rechargeable batteries are

not recommended.

The 3-in-1 sensor requires lithium

batteries in low temperature

1. Press the release lever and pull

off the lower housing of the

sensor.

2. Remove the battery compartment

cover. Take note of the A-B-C

switch setting inside the battery

compartment.

3. Insert 4 x AA batteries into the

battery compartment, as shown.

Follow the polarity (+/-) diagram

in the battery compartment.

4. Replace the battery cover and

lower housing of the sensor.

conditions. Cold temperatures can

cause alkaline batteries to function

improperly. Use lithium batteries in

the 3-in-1 sensor for temperatures

below -4ºF / -20ºC.

A-B-C Switch

set to match

display unit

A B C

•

I'~~-

~--- I

Display Unit Setup

1 Set the A-B-C Switch

Locate the A-B-C switch inside

the battery compartment. Set

the A-B-C switch to A, B or C.

You must select the same letter

choices for both the display unit

and the sensor in order for the

units to synchronize.

2 Install or Replace Backup

Batteries (optional)

1. Remove the battery

compartment cover.

2 Install Backup

Batteries

(optional)

3 AA batteries

2. Insert 3 x AA alkaline batteries

into the battery compartment,

as shown. Follow the polarity

(+/–) diagram in the battery

compartment.

3. Replace the battery cover.

3 Plug in Power Adapter

For the best performance, plug

in the power adapter as the main

power source for this product.

A-B-C Switch

set to match

sensor

Plug in Power Adapter

IMPORTANT: Batteries are a backup power source to preserve

records in the event of a power outage. Power adapter is

recommended as the primary power source to enjoy the full

functionality of this product.

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE

WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be

used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used

batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in ﬁre,

as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge

non-rechargeable batteries. DO NOT short-circuit the supply terminals.

Intelli-Time®Clock

Intelli-Time products are pre-programmed with the correct time and date. Intelli-

Time technology instructs the time and date to set themselves. All you need to

do is select your Time Zone and Daylight Saving Time preferences. The clock

will then automatically set itself and change for Daylight Saving Time.

Set the Time, Date & Units

Press the “ ” button, located on the back of the display unit, to enter SET

MODE. Once in set mode, the preference you are currently setting will blink on

the display.

To adjust the currently selected (ashing) item, press and release the “ “ or

“ “ buttons (press and HOLD to fast adjust).

To save your adjustments, press and release the “ ” button again to adjust

the next preference. The preference set order is as follows:

TIME ZONE

DST (Daylight Savings Time ON or OFF)*

CLOCK HOUR

CLOCK MINUTE

CALENDAR MONTH

CALENDAR DATE

CALENDAR YEAR

TEMPERATURE UNITS (ºF or ºC)

PRESSURE UNITS (inHg or hPa)

WIND UNITS (MPH or KPH)

You will automatically exit SET MODE if no buttons are pressed for 10 seconds.

Enter setup mode at any time by pressing the “ ” button.

* If you live in an area that observes Daylight Savings Time, DST should be set

to ON, even if it is not currently Daylight Savings Time.

Display Backlight Settings

This weather station’s color display features three different lighting settings:

High (100%) brightness, Medium (60%) brightness and Low (30%) brightness.

Using battery power alone, the backlight is available momentarily for 10

seconds by pressing the backlight button.

When display is powered with the power adapter, backlight remains on

at 100% brightness. Press the backlight button once to dim to 60% brightness;

press again to dim to 30%, press a 3rd time to enter “AUTO DIM” mode.

AUTO DIM appears below time.

AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.

MARCH 11- NOVEMBER 4 6:00 a.m. - 9:00 p.m. = 100% brightness

9:01 p.m. - 5:59 a.m.= 30% brightness

NOVEMBER 5 - MARCH 10 7:30 a.m. - 7:00 p.m.= 100% brightness

7:01 p.m. - 7:29 a.m. = 30% brightness

Placement for Maximum Accuracy

AcuRite sensors are sensitive to surrounding environmental conditions. Proper

placement of both the display unit and the sensor are critical to the accuracy and

performance of this product.

Display Unit Placement

Place the display unit in a dry area free of dirt and dust. To ensure

accurate temperature measurement, place out of direct sunlight and

away from heat sources or vents. Display unit stands upright for

tabletop use and is wall-mountable.

3-in-1 Sensor Placement

The 3-in-1 sensor is designed to remain outdoors all year long.

Choose an open location with no obstructions above or around the

sensor for the most accurate measurements.

Important Placement Guidelines

Display unit and sensor must be within 330 feet (100 m) of each other.

MAXIMIZE WIRELESS RANGE

Place units away from large metallic items, thick walls, metal surfaces, or other

objects that may limit wireless communication.

PREVENT WIRELESS INTERFERENCE

Place both units at least 3 feet (.9 m) away from electronic devices (TV, computer,

microwave, radio, etc.).

LOCATE AWAY FROM HEAT SOURCES

Position sensor away from heaters, air conditioners, chimneys, exhaust vents, asphalt

and concrete (surfaces that radiate heat).

LOCATE AWAY FROM HUMIDITY SOURCES

Avoid installing the sensor near pools, spas, or other bodies of water. Water sources

may impact humidity accuracy.

LOCATE AWAY FROM SPRINKLER HEADS

DO NOT install the sensor where it will be sprayed by a sprinkler system. This may

force water inside the sensor.

LOCATE AWAY FROM WIND OBSTRUCTIONS

DO NOT mount the sensor with obstructions around it.

Consider a location that is a wide open area, with few

structures around to ensure accurate wind speed measurement.

Visit us online to view installation photos and

video, or learn more about AcuRite technology: View Video

www.AcuRite.com/3in1

3-in-1 Sensor Installation Guidelines

INSTALLATION HEIGHT Mount the sensor at a minimum height of 5 feet (1.5 meters)

off the ground, in an open area. Higher is better for wind measurements - the

National Weather Service recommends 33 feet high!

MOUNTING OPTIONS The included mounting bracket is designed to screw directly

onto wooden posts or surfaces that are 2”x4” or larger. The sensor can also be

mounted directly to 3/4” steel pipe (available at hardware stores and home centers).

LEVEL INSTALLATION Use a

bubble level (not included) to ensure

level installation for accurate wind

measurement.

Top or Side Mount

1. Insert the mounting base into the hole

on the bottom of the sensor.

2. Use one of the screws included in the

hardware bag to fasten the lower

sensor housing to the mounting base.

3. Fasten mounting base to a post or

railing using 2 screws.

Pipe Mount

1. Insert pipe or similar item all the way into

the hole on the bottom of the sensor. Note:

Mounting base is not used.

2. Use one of the screws included in the

hardware bag to fasten the lower sensor

housing securely to the pipe.

The 3-in-1 sensor is now ready to use.

Basic Setup is Complete

The 3-in-1 sensor will now synchronize with

the display unit. It may take a few minutes

for synchronization to complete. If both or one of the units appear to be functioning

improperly, please refer to the troubleshooting section.

Top Mount Side Mount

Pipe Mount

Do not install during

electrical storms.

Do not place pipe

or sensor near

electrical lines or

electrical equipment.

Inhaltsverzeichnis

Andere ACU-RITE Wetterstation Handbücher

ACU-RITE

ACU-RITE 736 Bedienungsanleitung

ACU-RITE

ACU-RITE 250 Bedienungsanleitung

ACU-RITE

ACU-RITE 00634 Bedienungsanleitung

ACU-RITE

ACU-RITE 02030RM Bedienungsanleitung

ACU-RITE

ACU-RITE 00837W Bedienungsanleitung

ACU-RITE

ACU-RITE 00609SBDIA1 Bedienungsanleitung

ACU-RITE

ACU-RITE 737 Bedienungsanleitung

ACU-RITE

ACU-RITE 1525 Bedienungsanleitung

ACU-RITE

ACU-RITE 00829 Bedienungsanleitung

ACU-RITE

ACU-RITE 75107 Bedienungsanleitung

ACU-RITE

ACU-RITE 01033W Bedienungsanleitung

ACU-RITE

ACU-RITE 502 Bedienungsanleitung

ACU-RITE

ACU-RITE 01097 Bedienungsanleitung

ACU-RITE

ACU-RITE 02098 Bedienungsanleitung

ACU-RITE

ACU-RITE 06095 Bedienungsanleitung

ACU-RITE

ACU-RITE 01608 Bedienungsanleitung

ACU-RITE

ACU-RITE 01118 Bedienungsanleitung

ACU-RITE

ACU-RITE 02033 Bedienungsanleitung

ACU-RITE

ACU-RITE 250 Bedienungsanleitung

ACU-RITE

ACU-RITE 1605 Bedienungsanleitung

ACU-RITE

ACU-RITE Iris Bedienungsanleitung

ACU-RITE

ACU-RITE 00593W Bedienungsanleitung

ACU-RITE

ACU-RITE 1036 Bedienungsanleitung

ACU-RITE

ACU-RITE 992 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung