Adam Equipment WBW 3M Bedienungsanleitung

Adam Equipment

WBW & WBW-M SERIES (EN)

SERIES WBW (FR)

WBW / WBW..M EG, WBW..aM NTEP(DE)

SERIES WBW & WBW-M(ES)

SERIE WBW & WBW-M (IT)

(P.N. 3036610540, Revision B, November 014)

Adam Equipment strives to be more environmentally focused and uses recycled materials and environmentally

friendly packaging where possible. As part of this initiative we have developed a short manual that uses less

paper and ink to describe the main functions of your new Adam indicator/scale. A complete version is available

at www.adamequipment.com. Thank you for your support of Adam Equipment and we hope that you enjoy

your new scale.

ENGLISH: P 1 - 11

FRANÇAIS: P 12 - 43

DEUTSCH: P 44 - 76

ESPAÑOL: P 77 - 89

ITALIANO: P 90 - 103

EU DECLARATION: P 104

CONTENT

1.0 SETTING UP AND TURNING ON THE SCALES................................2

2.0 OPERATION.........................................................................................2

2.1 NUMERIC ENTRY METHOD.............................................................2

2.2 ZEROING...........................................................................................2

2.3 TARING.............................................................................................2

2.4 WEIGHING ........................................................................................3

2.5 CHECK-WEIGHING...........................................................................3

3.0 RS-232 SPECIFICATION .....................................................................4

4.0 CALIBRATION .....................................................................................4

5.0 ERROR CODES ...................................................................................5

6.0 SPECIFICATIONS................................................................................6

7.0 MENU STRUCTURE ............................................................................9

8.0 WARRANTY INFORMATION.............................................................10

9.0 SERVICE INFORMATION..................................................................11

1.0 SETTING UP AND TURNING ON THE SCALES

There are three series within the range: WBW-M, WBW and WBWa. The WBW-M scales are configured at the factory

for compliance with EN 45501, OIML R-76. They have different capacities and readabilities from the standard WBW

series. The WBW series are similar to the WBWa series except the WBW scales are usually set for metric units,

whereas for the WBWa series are usually set for imperial units.

SETTING UP

The WBW Series comes with a stainless steel pan. Place it on the top if already not installed. Do not press with

excessive force as this could damage the load cell inside.

Level the scale by adjusting the four feet. The scale should be adjusted such that the bubble in the spirit level is in

the centre of the level and the scale is supported by all four feet. Attach the power supply module to the bottom of

the scale and plug into the mains. Press the [O/I] key to start. The software revision number will be displayed

followed by a self-test showing all digits before the zero is displayed along with the unit of weight that was selected

last.

NOTE: the scale can be operated from the battery. If desired, the battery life is approximately 50 hours. When the

battery needs charging a symbol on the display will turn on. The battery should be charged for 12 hours for full

capacity.

2.0 OPERATION

2.1 NUMERIC ENTRY METHOD

To set a value when required, use the keys as given below-

- [Limit] key to increase the flashing digit

- [Unit] key to move to the next digit and

- [Tare] key to accept the value

2.2 ZEROING

You can press the [Zero] key at any time to set the zero point from which all other weighing and counting is measured.

The scales have an automatic re-zeroing function to account for

minor drifting or accumulation of material on a connected

platform. However you may need to press [Zero] to re-zero the

scale if small amount of weight is still shown when the platform is

empty.

2.3 TARING

Zero the scale by pressing [Zero]. The zero indicator will be on. Place a container on the pan.

Press [Tare] when the reading is stable. The weight that was displayed is stored as the tare value, leaving zero on

the display. The stable and Net indicator will be on.

As a sample is added only the weight of the product will be shown. The scale could be tared a second time if another

type of product was added to the first one.

Press [Tare] or [Zero] to remove the tare value and display zero. The Net indicator will disappear.

2.4 WEIGHING

To determine the weight of a sample, first tare an empty container if used, then place the sample in the container.

The display will show the weight and the unit of weight currently in use. To change the weighing unit press the [Unit]

key.

2.5 CHECK-WEIGHING

Check-weighing is a procedure to show a display or sound an alarm when the weight on the platform meets or

exceeds the values stored in the memory. The memory holds values for a high limit and a low limit. Either or both

the limits can be set by the user.

The LCD display will indicate whenever the weight is within or exceeds the limits by showing “OK” (mass is between

the limits), “HI”(mass is above the high limit) or “LO”( mass is below the low limit).

The limits can be locked by the manager (see the menu structure section) .A Limit Password must be used to change

the limits or recall other limits from memory.

Setting up the limits

In normal weighing, Press the [Limit] key. It will show the current high limit.The user will be asked for the password

if the current check-weighing password is anything other than “0000”. See the parameter “F4 PS” in menu structure.

Enter the correct password using the numeric entry method as mentioned in section 2.1. If the password is “0000”

it will display the last used high limit. The “HI” symbol will appear on the display.

Press [Tare] to accept the displayed high limit or enter the new high limit using the numeric entrymethod (see section

2.1). When the desired value is entered press [Tare] to accept the value. The “LO” symbol will be on. Display will

show the last used low limit. Set the low limit in the same way the high limit was set.

Pressing the [Tare] key will return the scale to weighing, with the Check-weighing function enabled.

NOTE: The limits are displayed in the weighing unit in use. The decimal point is fixed at the position that is used for

the current weighing unit. If the weighing unit is pounds:ounces, the limits are entered in pounds and decimal parts

of pounds. i.e. 6.0125 lb.

Limits stored in memory

If the scale is turned off, it stores the last high and low limits in the memory along with information about the

weighing unit in use when the limits were stored. If the scale is turned on again, the limits and the weighing

unit will still be active.

3.0 RS-232 SPECIFICATION

The RS-232 is not available in WBW scales.

4.0 CALIBRATION

The WBW-M scales should not be calibrated by the user. Calibration of the scales may make it illegal to use the

scales. Contact your local metrology standards office for further assistance.

The WBW non-approved scales are calibrated using metric weights when the weighing unit selected is either

kilograms or grams and using pound masses when the weighing unit selected is either pounds, ounces or

pounds:ounces.

To start the calibration turn the scale off and then turn it on again. Press [Tare] during the self-test. Scale will show

“P- - - - “. Enter code number “0000” using the numeric entry method (see section2.1) and press [Tare]. This will take

you directly to the calibration section.Display will show "UnLoAd".

Remove all weight from the pan and then press the [Tare] key when the scale is stable. After the Zero point is set,

the display will show “Ld xx”. Place the suggested calibration mass on the pan. It is best to use a weight close to the

full capacity of the scale. If the mass is different from the displayed value, enter the value of the mass in whole

numbers using the numeric entry method (see section 2.1). The kg or the lb symbol will be on to show the active unit.

Press the [Tare] key when the stable indicator is on. The scale will calibrate to the mass and then return to weighing.

Remove the calibration weight as soon as calibration is complete.

5.0 ERROR CODES

During the initial power-on testing or during operation, the scale may show an error message. The meaning of the

error messages is described below.

If an error message is shown, repeat the step that caused the message. If the error message is still shown then

contact your dealer for support.

ERROR

CODE

DESCRIPTION

POSSIBLE CAUSES

Err 4

Err 4Err 4

Err 4

Initial Zero is greater than allowed

(4% of maximum capacity) when

power is turned on or when [Zero]

is pressed.

Weight on the pan when turning the scale on.

Excessive weight on the pan when zeroing the scale.

Platform is not installed.

Improper calibration of the scale.

Damaged load cell.

Damaged Electronics.

Err 6

Err 6Err 6

Err 6

A/D count is not correct when

turning the scale on. Load cell is damaged.

Electronics is damaged.

Err 8

Err 8Err 8

Err 8

High limit input error Low limit is set first, then the high limit is set lower than

the low limit and high limit not equal to zero.

Err 9

Err 9Err 9

Err 9

Low limit input error High limit is set first, then the low limit is set higher than

the high limit and low limit not equal to zero.

FAIL H or

FAIL H or FAIL H or

FAIL H or

FAIL L

FAIL LFAIL L

FAIL L

Calibration error Improper calibration (should be within +10% of the

factory calibration). The old calibration data will be

retained until the calibration process is complete.

6.0 SPECIFICATIONS

EC Type Approved Models

WBW 1.5M WBW 3M WBW 6M WBW 15M

Kilograms

Max 1.5 kg 3 kg 6 kg 15 kg

e = 0.0005 kg 0.001 kg 0.002 kg 0.005 kg

Grams

Max 1500 g 3000 g 6000 g 15000 g

e = 0.5 g 1 g 2 g 5 g

WBW 2 / 5a WBW 4 / 9a WBW 8 / 18a WBW 16 / 35a

Kilograms

Maximum Capacity 2.000 kg 4.000 kg 8.000 kg 16.000 kg

Tare Range -2.000 kg -4.000 kg -8.000 kg -16.000 kg

Readability 0.0002 kg 0.0005 kg 0.001 kg 0.002 kg

Repeatability (S.D.) 0.0002 kg 0.0005 kg 0.001 kg 0.002 kg

Linearity (±) 0.0004 kg 0.001 kg 0.002 kg 0.004 kg

Grams

Maximum Capacity 2000 g 4000 g 8000 g 16000 g

Tare Range -2000 g -4000 g -8000 g -16000 g

Readability 0.2 g 0.5 g 1 g 2 g

Repeatability (S.D.) 0.2 g 0.5 g 1 g 2 g

Linearity (±) 0.4 g 1 g 2 g 4 g

Pounds

Maximum Capacity 5 lb 9 lb 18 lb 35 lb

Tare Range -5 lb -9 lb -18 lb -35 lb

Readability 0.0005 lb 0.001 lb 0.002 lb 0.005 lb

Repeatability (S.D.) 0.0005 lb 0.001 lb 0.002 lb 0.005 lb

Linearity (±) 0.001 lb 0.002 lb 0.004 lb 0.01 lb

Ounces

Maximum Capacity 80 oz 144 oz 288 oz 560 oz

Readability 0.01 oz 0.02 oz 0.05 oz 0.1 oz

Repeatability (S.D.) 0.01 oz 0.02 oz 0.05 oz 0.1 oz

Linearity (±) 0.02 oz 0.04 oz 0.1 oz 0.2 oz

Pounds:Ounces

Maximum Capacity 5 lb: 0.00 oz 9 lb:0.00 oz 18 lb:0.0 oz 35 lb: 0.0 oz

Readability 0.01 oz 0.02 oz 0.1 oz 0.1 oz

Repeatability (S.D.) 0.01 oz 0.02 oz 0.1 oz 0.1 oz

Linearity (±) 0.02 oz 0.04 oz 0.2 oz 0.2 oz

OTHER SPECIFICATIONS

Units of measure WBW-M : kg, g

WBW/WBW.a: kg, g, lb, oz, lb:oz

Tare Full range

Stabilisation Time 2 seconds typical

Operating Temperature

-10°C to 40°C

Power supply 12 VDC, 800 Ma through an external Power Supply Module

Battery Internal rechargeable battery (~50 hours operation)

Calibration Automatic External

Display 6 digits LCD digital display with capacity tracker and symbols for units

Scale Housing IP 65 Sealed ABS Plastic housing with Stainless Steel pan

Pan Size 210 x 173 mm

Overall Dimensions

(wxdxh) 231 x 265 x 153 mm

Net Weight 3.3 kg / 7.26 lb

Applications Weighing Scales

Functions Weighing, Check weighing

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Adam Equipment Skala Handbücher

Adam Equipment

Adam Equipment DCT 201 Bedienungsanleitung

Adam Equipment

Adam Equipment PTS plus Series Bedienungsanleitung

Adam Equipment

Adam Equipment 103 Bedienungsanleitung

Adam Equipment

Adam Equipment NETS ME Price Bedienungsanleitung

Adam Equipment

Adam Equipment MDW - 250L Bedienungsanleitung

Adam Equipment

Adam Equipment MUW 300L Bedienungsanleitung

Adam Equipment

Adam Equipment AQ Series Bedienungsanleitung

Adam Equipment

Adam Equipment Nimbus NBL Series Bedienungsanleitung

Adam Equipment

Adam Equipment CBW Series Bedienungsanleitung

Adam Equipment

Adam Equipment ASC Bedienungsanleitung

Adam Equipment

Adam Equipment CBK series Bedienungsanleitung

Adam Equipment

Adam Equipment WBZ Series Bedienungsanleitung

Adam Equipment

Adam Equipment CFC SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment CBC-M Series Bedienungsanleitung

Adam Equipment

Adam Equipment LHS Series Bedienungsanleitung

Adam Equipment

Adam Equipment CCT Series Bedienungsanleitung

Adam Equipment

Adam Equipment WBW Series Bedienungsanleitung

Adam Equipment

Adam Equipment CQT 202 Montageanleitung

Adam Equipment

Adam Equipment CQT1752GR Bedienungsanleitung

Adam Equipment

Adam Equipment CBC SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment BCT Series Bedienungsanleitung

Adam Equipment

Adam Equipment HIGHLAND SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment DUNE SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment MDW-160M Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung