Adaptec APA-1480 SlimSCSI Bedienungsanleitung
U
SER
S
G
UIDE
S
LIM
SCSI 1480 A
DAPTER
© 1997 Adaptec, Inc.
All rights reserved. Adaptec, and the
Adaptec logo are trademarks of Adaptec,
Inc. which may be registered in some
jurisdictions.
Printed in Singapore
STOCK NO.: 511537-00, Rev. A KL 8/97
R
▼ ▼ ▼ ▼ SlimSCSI 1480 Adapter
User’s Guide
iii
▼ ▼ ▼ ▼ Contents
Introduction 1
Contents of Kit 1
System Requirements 1
Installing the SlimSCSI 1480 2
Installing the SlimSCSI Windows 95 Driver 5
Using the SlimSCSI Adapter 6
Hot Plugging 6
Controlling the SCAM and Ultra Features 7
Understanding SCSI 10
SCSI IDs 10
SCAM Protocol 10
Terminating the SCSI Bus 11
Obtaining SCSI Cables 11
Connector Types 12
Troubleshooting 13
General Hardware Troubleshooting 13
General Software Troubleshooting 14
Windows 95 Troubleshooting 14
Contacting Adaptec 19
Electronic Support 19
Technical and Product Support 19
Sales and Ordering Information 20
1
Introduction
Congratulations on your purchase of Adaptec’s SlimSCSI 1480. The
SlimSCSI 1480 delivers full 32-bit PCI performance at speeds up to
20 MBytes/sec., allowing your high-performance SCSI devices to
operate at their maximum speed. Enjoy the same versatility and per-
formance as a desktop PC, plus the convenience of instant plug-in
connections and hot swapping.
Contents of Kit
■SlimSCSI 1480 CardBus-to-UltraSCSI Adapter
■SlimSCSI 1480 setup diskette
■SlimSCSI 1480 Adapter User’s Guide
■50-pin high-density cable
■50-pin low-density cable
■Adaptec EZ-SCSI software and Quick Reference Guide
■Mail-in card for free DB25 cable
■Registration card
System Requirements
■Portable PC with CardBus-enabled PC Card slot
■Windows®95, version 4.00 950B or later
2
SlimSCSI 1480 User’s Guide
Note:
The CardBus specification differs from the standard
PC Card (PCMCIA) specification. As a result, CardBus
adapters like the SlimSCSI 1480 will not operate in, and can-
not be inserted in, a standard PC Card slot.
Installing the SlimSCSI 1480
Follow these steps to install the SlimSCSI 1480 and connect your
SCSI devices to it:
1
Remove the SlimSCSI 1480 from its packaging.
2
Determine which of the two 50-pin cables you will use to con-
nect the SlimSCSI 1480 to your first (or only) SCSI device. To
do this, see which cable connector (high-density or low-den-
sity) fits the SCSI connector on the back of the device.
Note:
If your SCSI device has a DB25 (25-pin) connec-
tor, you can order a free DB25 cable from Adaptec by
sending in the card included in this User’s Guide.
3
Connect the SlimSCSI cable to the SlimSCSI 1480, as shown
below:
CardBus Slots
SlimSCSI 1480
SlimSCSI Connector
3
Installing the SlimSCSI 1480
4
Plug the other end of the cable into the first (or only) SCSI
device, as shown below. Make sure the SCSI device is not
powered.
5
(Optional) Connect up to two additional UltraSCSI devices by
daisy-chaining them to the first device, as shown below:
6
Be sure that each SCSI device has a unique SCSI ID ranging
from 0 to 6. If any two devices have the same ID, change the
SCSI ID of one device. This is usually done by changing a
switch on the back of the device. (For more information, see
SCSI IDs on page 10.)
SCSI Connector SCSI Device
Terminator
SCSI Devices
Terminator
4
SlimSCSI 1480 User’s Guide
The diagram below shows a typical SCSI device with a select-
able SCSI ID switch:
7
Terminate the last (or only) SCSI device connected to the
SlimSCSI 1480. Read the device documentation if you are not
sure how to terminate the device, or refer to Terminating the
SCSI Bus on page 11.
8
Be sure that at least one external SCSI device provides SCSI
bus termination power or that the last device on the bus sup-
plies termination power to itself. Read the device documenta-
tion if you are not sure whether the SCSI device provides
termination power.
9
Connect all power cables to the SCSI devices. Then power up
all the devices.
10
Insert the SlimSCSI 1480 into one of your portable PC’s Card-
Bus slots.
11
Power up your portable PC.
Next, you must install the SlimSCSI Windows 95 driver.
5
Installing the SlimSCSI Windows 95 Driver
Installing the SlimSCSI
Windows 95 Driver
1
If Windows 95 is not already running, start it now.
2
If the SlimSCSI 1480 is not already inserted in the CardBus slot,
insert it now. Then wait until Windows 95 finishes building the
database information for the adapter. The Windows 95 Update
Device Driver Wizard starts automatically.
3
When you are prompted by the Update Device Driver wizard,
insert the SlimSCSI 1480 Setup Diskette for Windows 95 in the
floppy disk drive. Click the Next button.
Note:
Refer to the Windows 95 Device Driver Wizard
Help if you have questions about installing the driver.
4
If you see Adaptec APA-1480 CardBus SCSI Controller in the
dialog box, click the Finish button.
If you see a message prompting you to insert the disk that is
already in the floppy drive, click OK. Then type a: as the
source from which to copy files and click OK again.
5
Wait until the PC Card (PCMCIA) icon appears on the
Windows taskbar in the lower right corner of the screen. This
indicates that the driver is successfully installed!
If the PC Card icon does not appear on the taskbar, click the
Start button and select Settings and Control Panel. In the Con-
trol Panel, double-click the PC Card (PCMCIA) icon. In the
Properties dialog box, select Show control on taskbar if it is
not already selected and click OK. The PC Card icon should
then appear on the taskbar.
Congratulations! You have successfully installed the SlimSCSI 1480!
6
SlimSCSI 1480 User’s Guide
Using the SlimSCSI Adapter
Hot Plugging
After you install the APA-1480 driver for the SlimSCSI 1480, you can
insert or remove the SlimSCSI 1480 at any time except when data is
being transferred on the SCSI bus. This is called hot plugging. (You
can tell that data is being transferred if the SCSI device activity light
is on.) Follow these steps to remove the SlimSCSI 1480 while
Windows 95 is running
1
Click on the small PC Card (PCMCIA) icon in the lower right
corner of the screen. You will see a dialog box similar to the
following:
2
Select Adaptec APA-1480 CardBus UltraSCSI Adapter.
3
Click the Stop button.
4
When you see the message You may safely remove this device,
remove the SlimSCSI 1480 from the slot.
Andere Handbücher für APA-1480 SlimSCSI
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Adaptec Adapter Handbücher
Adaptec
Adaptec 131CA - AAA RAID Controller Montageanleitung
Adaptec
Adaptec AVA-2902E Bedienungsanleitung
Adaptec
Adaptec AFW-8300 Bedienungsanleitung
Adaptec
Adaptec AUA-1420 Bedienungsanleitung
Adaptec
Adaptec XHub4 - Hub - USB Bedienungsanleitung
Adaptec
Adaptec AHA-3940U Bedienungsanleitung
Adaptec
Adaptec AHA-3980 Bedienungsanleitung
Adaptec
Adaptec 39320A-R Bedienungsanleitung
Adaptec
Adaptec 81605ZQ Bedienungsanleitung
Adaptec
Adaptec 29320LPE - SCSI Card Storage Controller U320 320... Bedienungsanleitung
Adaptec
Adaptec Trantor T130 Handbuch
Adaptec
Adaptec ARO-1130U2 Montageanleitung
Adaptec
Adaptec AIC-7890 Bedienungsanleitung
Adaptec
Adaptec Trantor T160 Handbuch
Adaptec
Adaptec AUA-1411 Bedienungsanleitung
Adaptec
Adaptec DuoConnect AUA-3121 Bedienungsanleitung
Adaptec
Adaptec 29320ALP Bedienungsanleitung
Adaptec
Adaptec T-128 Bedienungsanleitung
Adaptec
Adaptec RCM-FC2500 Bedienungsanleitung
Adaptec
Adaptec APA-1350 Bedienungsanleitung
