Addonics Technologies HD9SITDRHS Bedienungsanleitung

Technical Support

If you need any assistance to get your unit functioning properly, please have your

product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

v3.1.11

www.addonics.com

User Guide

1:9 HS HDD Duplicator Pro

(HD9SITDRHS)

T E C H N O L O G I E S

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Drive InstallationGuide

Step 1

Use a Philips screwdriver to

turn the cover securing screw

clockwise into the "OPEN"

position.

Step 2

Slide the aluminum cover towards

the back end of the Diamond

enclosure and remove it.

Step 3

For SATA Drive:

Carefully place the SATA hard

drive with the label facing up into

the Diamond Enclosure. Push

the hard drive towards the back

end to secure the drive connec-

tors onto the Diamond

enclosure’s SATA connector.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

For IDE Drive

Note: Configure your IDE hard

drive as Master device

Connect the 4-Pin Molex cable to

the power connector on the IDE

hard drive. Carefully place the IDE

hard drive with the label facing up

into the Diamond enclosure. Push

the hard drive toward the back

end to secure the drive connectors

onto the Diamond enclosure’s IDE

connector.

Step 4

Turn the Diamond enclosure over

with the hard drive mounting holes

facing up. Use the included flat

head screws to secure the hard

drive onto the bottom of the enclo-

sure and turn in the screw to the

“LOCK” position.

Step 5

Insert the enclosure into a cradle in

the duplicator and secure it in place

with the handle and turn the cradle's

lock to the LOCK position. Note: the

drive will not power up until the

cradle's lock is in the LOCK posi-

tion.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Connecting the Power Cable and Powering On

a.Connect the power cord provided from the wall outlet tothe back of the tower.

b. Turn on the main power switch on the rear of the chassis.

c. Push the power button on the front of the unit to turn on the HDD duplicator.

There are four buttons and an LCD on the panel of HDD Duplicator.

1 – LCD shows a function or a message.

2 – it is used to scroll up function menus.

3 – it is used to scroll down function menus.

4 – it is used to execute a function.

5 – it is used to cancel a function.

Duplicator Panel

ENT

ESC

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Main Menu

1. Copy HDD

Scans the ports, then copies from the source to any targets found.

2. Async Copy HDD

Scans the ports, then copies from the source to any targets found. More

drives may be added before the process is complete, they will begin the

process as soon as they are detected.

3. Compare HDD

Scans the ports, then any targets found will be compared to the source.

4. Async Compare

Scans the ports, then any targets found will be compared to the source.

More drives to compare may be added before the process is complete,

they will begin the process as soon as they are detected.

Quick Start

By default, the duplicator will initialize, scan for drives and offer the

copy function. Insert the source and target drives, power up the unit,

wait for the copy function to appear, then press ENT.

Canceling Functions

When selecting menu options, canceling is done by pressing ESC.

When the unit is busy performing an operation such as copy, verify,

or overwrite, the operation can be canceled by holding the ESC

button until the unit beeps.

Duplicator Functions

The duplicator has three menu sections: The Main menu, Setup

Options, and Advanced Setup Options. Setup Options is accessed

through the Main menu. Advanced Setup Options is accessed by

holding the ESC button from any other menu until the unit beeps.

When the duplicator completes some of the functions it will record a

log of the most recent activity. Select VIEW LOG from the Main

Menu to review the latest function's results.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

5. PreScan Source

Reads all blocks on the source drive to confirm no I/O errors are encoun-

tered.

6. ReScan BUS

Manually scans all ports and reports how many units were found.

7. Source Size

Examines the source drive and reports total space and space used, if

drive contains compatible partitions. Press up/down to change display,

ESC to exit.

8. Secure Erase

Scans all ports, then erases all data on all connected drives.

NOTE: some drives will remain in a locked state when the process is

complete. Drives that are locked may not appear to an operating system

and will cause an I/O error if used as a target in the duplicator. If this

happens, start secure erase again and hold ESC to cancel the operation

a few moments after it begins.

9. Overwrite

Overwrite is used to write data onto the entire hard disk, it will destroy all

data on all HDDs connected to the duplicator (including Source HDD) by

writing data to all sectors. There are 4 sub-options: One pass (zero), One

pass (random), 3 pass and 7 pass.

10. Setup

Enters the Setup menu. See Setup Options.

11. View Log

Shows the results from the most recent drive operation, such as copy,

overwrite, etc.

12. Adv Setup

Enters the Advanced Setup Menu. Only available by holding ESC on any

Main Menu option. See Advanced Setup Options.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Setup options

10-1. Language

Use this option to select the language of the system, currently only Eng-

lish is supported.

10-2. Copy Size

Controls how much of the source drive to use for copy operations, in

percentage. Default setting is ALL (100%).

10-3. Startup Menu

Sets the first menu option to appear after boot. Default setting is Copy

HDD.

10-4. Auto Compare

Controls whether or not targets are compared automatically when copy is

complete. Default setting is OFF.

10-5. Button Sound

Enables audible beep when pressing buttons. Default setting is ON.

10-6. Device Info

Displays information about connected drives. Main display is drive manu-

facturer and size. Press up/down to select drives, ENT to display model

number and firmware revision of selected drive.

10-7. System Info

Displays firmware version and date.

10-8. Fast Copy

When this setting is ON, the duplicator will attempt to copy the source

drive's contents instead of the entire disk. Also controls Compare function.

Default setting is OFF.

NOTE: Target drive size is still required to be equal to or greater than

source. Only works with source drives formatted using Master Boot

Record. If the source drive has a boot record other than MBR, the entire

disk will be copied as if Fast Copy were OFF. If the source drive is format-

ted with a Master Boot Record and contains only FAT32 or NTFS parti-

tions, identical partitions will be created on the target(s) and only the files

will be copied. If the source drive with MBR format includes partitions

other than FAT32 or NTFS, all sectors of all partitions (including FAT32

and NTFS) will be duplicated.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

10-9. Auto Start Drive

When source drive is present, inserting a target drive will cause copy

process to begin automatically. Default setting is OFF.

10-10. Auto Start Timer

Sets delay in time after target insertion before beginning auto copy

process if Auto Start Drive is ON. Default setting is OFF (no delay).

10-11. Tolerance Size

Sets the minimum target size in percentage compared to the source that

is allowed to use for copying. Default is 100% (equal in size).

NOTE: Leaving this setting at 100% or using for minor adjustments only

is strongly recommended. Permitting target size less than source size

may result in inaccurate copies.

10-12. BootTime Delay

This option is used to set boot delay time. Default setting is 5 seconds.

10-13. Quick Compare

Sets Compare function to stop after a small amount of data has been

verified, up to 100MBytes. Default setting is OFF.

10-14. Copy with Size

Causes duplicate drive to report to an operating system the exact same

total size as source when copy is complete. Works only on drives format-

ted using a Master Boot Record. Default setting is OFF.

Advanced Setup Options

12-01. Read Error Skip

Allows duplicator to ignore I/O errors while reading source drive. Default

setting is OFF.

12-02. Update Firmware

Used to apply firmware updates. Connect a drive formatted as FAT

containing one partition with the firmware file in the root directory.

NOTE: This function scans the entire disk before proceeding. Providing a

drive that is as small as possible is strongly recommended.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

12-03. Compare Firmware

Used to confirm correct firmware. Connect a drive formatted as FAT

containing one partition with the firmware file in the root directory.

NOTE: This function scans the entire disk before proceeding. Providing

a drive that is as small as possible is strongly recommended.

12-04. Quick Erase HDD

Scans the ports, then quickly erases all sectors on all connected drives.

12-05. Full Erase HDD

Scans the ports, then completely erases all sectors on all connected

drives.

12-06. H/W Diagnostic

Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.

12-07. Load Default

Resets all configuration settings to default.

12-08. Copy HPA

Enables copy functions to duplicate the source drive's Host Protected

Area. Normally this area is defined as not available to a host controller

as defined by ATA/SATA specifications.

12-09. Burn In

Runs a function continuously until aborted. Selections are Copy &

Compare, Compare, Async Cpy & Cmp, Async Compare.

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

Inhaltsverzeichnis

Andere Addonics Technologies Disc-Duplikator Handbücher

Addonics Technologies

Addonics Technologies HD4SNH Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFH15-C Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGC3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies CFASTD5 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSI325 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11325DX Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDU11SAS Bedienungsanleitung

Addonics Technologies

Addonics Technologies DDU3SAS Bedienungsanleitung

Addonics Technologies

Addonics Technologies DigiCopier III DGC3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies Jasper II SID Bedienungsanleitung

Addonics Technologies

Addonics Technologies ZHDUESA Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDMU3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies JD2-3SN25 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSI325-A Bedienungsanleitung

Addonics Technologies

Addonics Technologies Jasper II JD2P3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies ST5DVRE Bedienungsanleitung

Addonics Technologies

Addonics Technologies ST55HPMXA Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSI325AES Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSAS Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGBRC1 Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGBRC7 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11SNDX Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS325DX Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11NB Bedienungsanleitung

Beliebte Disc-Duplikator Handbücher anderer Marken

Riso

Riso CV Series Handbuch

MicroBoards Technology

MicroBoards Technology GX-2 Bedienungsanleitung

Carry

Carry Pro118 Bedienungsanleitung

CopyPro

CopyPro PowerPro II Bedienungsanleitung

Primera

Primera Max Bedienungsanleitung

Logicube

Logicube EchoPlus-NG Bedienungsanleitung

Silca

Silca Delta 2000 SA Bedienungsanleitung

Reflex7

Reflex7 Daisy Chain Series Bedienungsanleitung

Vinpower Digital

Vinpower Digital SharkCopier DC Bedienungsanleitung

Codonics

Codonics Virtua E Bedienungsanleitung

Octave

Octave Copy Master II Bedienungsanleitung

Kanguru

Kanguru U2-DVDDUPE-S Bedienungsanleitung

StarTech.com

StarTech.com 8STSATDUP11 Bedienungsanleitung

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Bedienungsanleitung

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Bedienungsanleitung

Telex

Telex SpinWise Bedienungsanleitung

Aleratec

Aleratec 260206 Bedienungsanleitung