ADJ HYDRO BEAM X1 Bedienungsanleitung

User Instructions

HYDRO BEAM X1

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

08/21/19 11.0 11 / 14 Initial Version

Date Document

Version

Software

Version >

DMX Channel

Mode Notes

10/01/19 1.2 N/C N/C Software Update Instructions Added

12/17/19 1.3 1.3 N/C Updated Display Lock/Unlock Feature

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 2

Hydro Beam X1 Table of Contents

Introduction

Features I Warranty Registration

IP65 Notice

Safety Guidelines

Overview

Discharge Lamp Warning

Lamp Installation

Torque Settings & IP Tester

Screw Locations

Fixture Installation

Connections

DMX Set Up

DMX Addressing

DMX Channel Modes

Gobos

System Menu

WiFly Control

Error Codes

Dimensional Drawings

Updating the Software

Power Linking I Cleaning

Limited Warranty (USA Only)

Technical Specications

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 3

Hydro Beam X1 Introduction

Unpacking: Thank you for purchasing the Hydro Beam X1 by ADJ Products, LLC. Every Hydro Beam

X1 has been thoroughly tested and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during shipping. If the carton appears to be

damaged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit has arrived intact. In the case damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The ADJ Hydro Beam X1 is a DMX intelligent, IP rated, high powered, moving head fixture.

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. This product is intended to be used by

professionally trained personnel only and is not suitable for private use.

These instructions contain important safety information regarding the use and maintenance of this

unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Hydro Beam X1 Features

• IP65 Outdoor Rated

• Electronic Dimming 0-100%

• DMX-512 protocol

• IP65 Locking 5-Pin XLR Connector In & Out

• Multiple DMX Modes

• IP65 Locking Power Connector In & Out

• Colors: 14 + Open (Including CTB & UV)

• Gobos: 15 Gobos + Open

• Prism: Rotating 16-Facet Circular

• Frost Effect

• Multiple Unit Power Linking (See page 38)

Included:

1 x IP65 Locking Power Cable

2 x Omega Brackets

Hydro Beam X1 Warranty Registration

The Hydro Beam X1 carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under war-

ranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by

contacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 4

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 5

Hydro Beam X1 IP Notice

IP65 RATED

An IP rated lighting xture is one, which is commonly installed in outdoor environments

and has been designed with an enclosure that eectively protects the ingress (entry)

of external foreign objects such as dust and water. The International Protection (IP)

rating system is commonly expressed as "IP" (Ingress Protection) followed by two

numbers (i.e. IP65) where the numbers dene the degree of protection. The rst digit

(Foreign Bodies Protection) indicates the extent of protection against particles entering

the xture and the second digit (Water Protection) indicates the extent of protection

against water entering the xture. An IP65 rated lighting xture is one, which has been

designed and tested to protect against the ingress of dust (6) and low-pressure water

jets from any direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS

NOT suitable for marine and/or coastal environment installations. Installing

this xture in a marine and/or coastal environment may cause corrosion and/

or excessive wear to the interior and/or exterior components of the xture.

Damages and/or performance issues resulting from installation in a marine

and/or coastal environment will void the manufactures warranty and will NOT be subject

to any warranty claims and/or repairs.

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 6

Hydro Beam X1 Safety Guidelines

FOR YOUR OWN PERSONAL SAFETY, PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY

BEFORE YOU ATTEMPT TO INSTALL OR OPERATE THIS UNIT!

• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS

YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM

MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND

GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO

ANY WARRANTY CLAIMS AND/OR REPAIRS.

• DO NOT PLUG THE FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH THE FIXTURE DURING OPERATION AS IT MAY BE HOT!

KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

• ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC GREASE

(AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR

ELECTRICAL SHORT CIRCUIT.

• IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE CHANGES SUCH AS RELOCATION

FROM AN OUTDOOR COLD TO AN INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE

ON IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF ENVIROMENTAL TEMPERATURE

CHANGE CAN CAUSE INTERNAL FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT HAS

REACHED ROOM TEMPERATURE BEFORE POWERING ON.

• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• Be sure that the local power outlet is compatible with the required voltage for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used to

reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this

device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point

where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 38 for cleaning

details.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other

appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when the appliance does not appear to operate

normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 7

Hydro Beam X1 Safety Guidelines

SAFETY G U I DELINES

To guarantee a smooth operation, it is important to follow all instructions and guidelines in

this manual. ADJ Products, LLC is not responsible for injury and/or damages resulting

from the misuse of this fixture due to the disregard of the information printed in this

manual. Only qualified and/or certified personnel should perform installation of this fixture

and only the original rigging parts included with this fixture should be used for installation.

Any modifications to the fixture and/or the included mounting hardware will void the

original manufactures warranty and increase the risk of damage and/or personal injury.

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.

DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID

YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM

MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF

SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID

THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY

WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT!

KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY

SEALED WITH A DIELECTRIC GREASE (AVAILABLE AT MOST

ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION AND/OR

ELECTRICAL SHORT CIRCUIT.

IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE

CHANGES SUCH AS RELOCATION FROM AN OUTDOOR COLD TO AN

INDOOR WARM ENVIRONMENT, DO NOT POWER THE FIXTURE ON

IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT OF

ENVIRONMENTAL TEMPERATURE CHANGE CAN CAUSE INTERNAL

FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF UNTIL IT

HAS REACHED ROOM TEMPERATURE BEFORE POWERING ON.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 8

Hydro Beam X1 Safety Guidelines

S A FETY GUI D ELI N E S

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET UV

RADIATION! FIXTURE EMITS HIGH INTENSITY WAVELENGTH

OF ULTRAVIOLET UV LIGHT FROM THE UV COLOR FILTER.

WEAR PROPER EYE AND SKIN PROTECTION. AVOID

PROLONGED PERIODS OF EXPOSURE TO UV COLOR FILTER.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING

UV PAINTS ON SKIN. AVOID DIRECT EYE AND/OR SKIN

EXPOSURE AT DISTANCES LESS THAN 11 feet (3.3m). DO NOT OPERATE FIXTURE

WITH DAMAGED/MISSING EXTERNAL COVERS. DO NOT LOOK DIRECTLY INTO THE

UV LIGHT AND/OR VIEW UV LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT

MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT. INDIVIDUALS SUFFERING

FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DIS-ORDERS, OR

INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT

IF EXPOSED TO THE ULTRAVIOLET UV LIGHT EMITTED FROM THE UV LED.

DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow

approximately 60 minutes for the fixture to cool down before servicing.

DO NOT shake fixture; avoid brute force when installing and/or operating fixture.

DO NOToperate fixture if the power cord has become frayed, crimped, damaged and/or if any

of the power cord connectors are damaged and do not insert into the fixture securely with ease.

NEVER force a power cord connector into the fixture. If the power cord or any of its

connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots; these must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.

When installing fixture in a suspended environment, always use mounting hardware that is no

less than M10 x 25 mm, and always attach an appropriately rated safety cable.

ALWAYS disconnect fixture from main power source before performing any type of service

and/or cleaning procedure. Only handle the power cord by the plug end; never pull out the

plug by tugging the wire portion of the cord.

During the initial operation of this fixture, a light smoke or smell may emit from the interior

of the fixture. This is a normal process and is caused by excess paint in the interior of the casing

burning off from the heat associated with the lamp and will decrease gradually over time.

Consistent operational breaks will ensure fixture will function properly for many years.

ONLY use the original packaging and materials to transport the fixture in for service.

ADJ Products, LLC - www.adj.com - Hydro Beam X1 User Manual Page 9

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which

are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ

lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,

glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,

discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures

from all manufacturers. Although there is no true way to fully prevent this issue from happening, the

guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service

for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT

SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,

INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.

DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

Hydro Beam X1 Safety Guidelines

Andere Handbücher für HYDRO BEAM X1

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ 7P HEX IP Bedienungsanleitung

ADJ

ADJ MB DMX II Bedienungsanleitung

ADJ

ADJ MB DMX II Bedienungsanleitung

ADJ

ADJ MIRAGE Q6 PAK Bedienungsanleitung

ADJ

ADJ ECO UV BAR 50 IR Bedienungsanleitung

ADJ

ADJ FOCUS WASH 400 Bedienungsanleitung

ADJ

ADJ ENCORE BURST 200 Bedienungsanleitung

ADJ

ADJ TRI18XS Bedienungsanleitung

ADJ

ADJ PAR Z100 5K Bedienungsanleitung

ADJ

ADJ MEGA HEX PAR Bedienungsanleitung

ADJ

ADJ Vizi BSW 300 Bedienungsanleitung

ADJ

ADJ ENCORE FR50Z Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ Eliminator Lighting FROST FX BAR W Bedienungsanleitung

ADJ

ADJ PAR Z120 RGBW Bedienungsanleitung

ADJ

ADJ wifly bar qa5 Bedienungsanleitung

ADJ

ADJ LINK Bedienungsanleitung

ADJ

ADJ ELEMENT QA Bedienungsanleitung

ADJ

ADJ VIZI BEAM 12RX Bedienungsanleitung

ADJ

ADJ ENCORE BURST RGBW IP Bedienungsanleitung

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ M-103HD Bedienungsanleitung

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ VIZ870 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung