ADJ MINI DEKKER LZR Bedienungsanleitung

User Instructions

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

www.americandj.eu

8/16

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 2

herein are subject to change without notice. ADJProducts, LLC logo and identifying product names and numbers

herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of

copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product

names used in this document may be trademarks or registered trademarks of their respective companies and

are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered

trademarks of their respective companies.

ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment,

building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with

the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe,

unsufficient and negligent assembly, installation, rigging, and operation of this product.

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 3

Contents

INTRODUCTION.......................................................................................................................................................................4

GENERAL INSTRUCTIONS ........................................................................................................................................................4

FEATURES................................................................................................................................................................................4

SAFETY PRECAUTIONS ............................................................................................................................................................5

DMX SET UP ............................................................................................................................................................................6

LAYOUT ...................................................................................................................................................................................7

LASER WARNING LABELS ........................................................................................................................................................8

SYSTEM MENU........................................................................................................................................................................8

OPERATING INSTRUCTIONS ..................................................................................................................................................11

MASTER-SLAVE SET UP .........................................................................................................................................................11

UC IR/AIRSTREAM APP CONTROL.........................................................................................................................................12

2 CHANNEL DMX MODE .......................................................................................................................................................12

CAD DRAWING......................................................................................................................................................................12

7 CHANNEL DMX MODE .......................................................................................................................................................13

FUSE REPLACEMENT .............................................................................................................................................................13

TROUBLE SHOOTING.............................................................................................................................................................13

CLEANING..............................................................................................................................................................................14

SPECIFICATIONS....................................................................................................................................................................14

ROHS - A great Contribution to the Conservation of Environment.....................................................................................15

WEEE –Waste of Electrical and Electronic Equipment ........................................................................................................15

NOTES ...................................................................................................................................................................................16

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 4

INOZIONE

INTRODUCTION

Unpacking: Thank you for purchasing the Mini Dekker LZR by ADJ Products, LLC. Every Mini Dekker LZR has

been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton

for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your

fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case

damage has been found or parts are missing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without first contacting customer support.

Introduction: The Mini Dekker LZR is part of ADJ’s continuing pursuit for creating high quality affordable

intelligent fixtures. The Mini Dekker LZR is a DMX intelligent LED mooflower effect with laser. This fixture can

be used in a stand alone mode or connected in a Master/Slave configuration. This fixture has three operating

modes: Sound Active mode, Show mode, and DMX control.

Customer Support: If you encounter any problems, please contact your trusted American Audio shop.

We also offer the possibility, to contact us directly: You can contact us via our website www.americandj.eu or

via email: support@americandj.eu

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will

void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ.

PLEASE recycle the shipping carton when ever possible.

GENERAL INSTRUCTIONS

To optimize the performance of this product, please read these operating instructions carefully to familiarize

yourself with the basic operations of this unit. These instructions contain important safety information regarding

the use and maintenance of this unit. Please keep this manual with the unit, for future reference.

FEATURES

• Includes Hanging Yoke

• 3 Operating Modes: Show Mode, Sound Active, & DMX Control

• Light Weight

• Strobing

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 2 DMX Channel Modes: 2 Channels & 7 Channels

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 5

SAFETY PRECAUTIONS

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or

break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and

fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between

this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 14 for cleaning

details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or

other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in performance.

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 6

DMX SET UP

Power Supply: The ADJ Mini Dekker LZR contains a automatic voltage switch, which will auto sense the voltage

when it is plugged into the power source. With this switch there is no need to worry about the correct power

voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to

the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure

proper DMX data transmission, when using several DMX fixtures try to usethe shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a

fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or

anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Mini Dekker LZR

has two DMX channel modes; a 2 channel mode and 7 channel mode. The DMX address

is set electronically using the controls on the rear panel of the unit. Your unit and your DMX

controller require aapproved DMX-512 110 Ohm Data cable for data input and data output.

We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to

use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all

professional sound and lighting stores). Your cables should be made with a male and

female XLR connector on either end of the cable. Also remember that DMX cable must be

daisy chained and cannot be split.

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the

XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to

come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic

behavior.

Figure 2

XLR Pin Configuration

Pin1 = Ground

Pin2 = Data Compliment (negative)

Pin3 = Data True (positive)

Figure 3

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on

the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 wattresistor which is connected between

pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector

of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T)

will decrease the possibilities of erratic behavior.

Termination reduces signal errors and avoids

signal transmission problems and interference. It is

always advisable to connect a DMX terminal,

(Resistance 120Ohm 1/4 W) between PIN 2 (DMX-

) and PIN 3 (DMX +) of the last fixture.

Figure 4

Figure 1

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 7

DMX SET UP (continued)

5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmission in

place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data

cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric

stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor

3-pin XLR Female (Out)

5-pin XLR Male (In)

Ground/Shield

Pin 1

Data compliment (- signal)

Pin 2

Data True (+ signal)

Pin 3

Not used

Do Not Use

Not used

Do Not Use

LAYOUT

1.Function Display: Used to show the various menus and the selected functions.

2.Button:

To select the programming functions

To go forward in the selected functions

DOWN

To go backward in the selected functions

ENTER

To confirm the selected functions

3. DMX IN/OUT: For DMX512 links, use 3-pin XLR plug cable to link the unit together.

4. POWER IN: Used to connect to supply power.

5. Key for Laser: To turn on/off the laser Led. (Only for EU version)

American Version

Europe Version

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 8

LASER WARNING LABELS

SYSTEM MENU

American Version

Europe Version

SPEC

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 9

SYSTEM MENU (continued)

DMX Address

Channel Mode

Show Mode

Show Speed

Slave Mode

Sound State

Sound Sense

Master Mode

Blackout Mode

Hold Last state

Led

Strobe

Display Inversion

Reset

Fixture Hours

Software Version

Auto Test

A.D.J. Supply Europe B.V. –www.americandj.eu –Mini Dekker LZR Instruction Manual Page 10

System Menu: When making adjustments press ENTER to confirm your setup then press and hold the

MENU button for at least 3 seconds. To exit without making any adjustments press the MENU button.

The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.

2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired

address. Press ENTER to set your desired DMX address.

CHND - This will let select your desired DMX channel mode.

1. Press the MENU button until “CHND” is displayed, press ENTER. The current DMX channel mode will be

displayed

2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and

exit.

SHND - Show modes 0-2 (Factory programs).

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between 0-6. Shows 1-2 are factory programs, while

show “0” is random mode. Use the UP or DOWN buttons to find your desired show.

3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3

seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN

buttons.

SPEE - Show mode speed.

1. Press the MENU button until “SPEE” is displayed, press ENTER.

2. A number between 0-100 will now be displayed, the number is the current speed setting. Use the UP or

DOWN buttons to adjust the show speed. “0” being the slowest speed and “100” being the fastest.

3. Press ENTER to set the speed then press and hold the MENU button for at least 3 seconds to show mode.

SLND - This will let you set unit as a master or slave in a master/slave configuration.

1. Press the MENU button until “SLND” is displayed, press ENTER. Either “MAST”, “SL 1”, or “SL 2” will be

displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.

Note: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to “SL 2”,

the fixtures will now have contrast movement to each other.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to activate sound

active mode, or “OFF” to deactivate sound active mode.

3. Press ENTER to confirm.

SOSE - In this mode you can adjust the sound sensitivity.

1. Press the MENU button until “SOSE” is displayed, press ENTER.

2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0

being the least sensitive, and 100 being the most sensitive.

3. When you have found your desired setting press ENTER to confirm.

NODN - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,

or power is lost, the operating mode chosen in this setup is the running mode the fixture will revert to.

You can also set this as the operating mode you would like the unit to return to when power is applied.

1. Press the MENU button until “NODN” is displayed, and either “MASL”, “BLND”, or “LAST” will be displayed

beneath.

2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an operating

mode you would like the unit to start up in when power is applied or the DMX signal is lost.

SYSTEM MENU (continued)

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ 1226100361 Bedienungsanleitung

ADJ

ADJ 1223200047 Leitfaden

ADJ

ADJ FOCUS WASH 400 Bedienungsanleitung

ADJ

ADJ SCENE SETTER 48 Bedienungsanleitung

ADJ

ADJ UV Panel HP Bedienungsanleitung

ADJ

ADJ penta pix Bedienungsanleitung

ADJ

ADJ M-1212 Bedienungsanleitung

ADJ

ADJ M-103HD Bedienungsanleitung

ADJ

ADJ BUBBLETRON Bedienungsanleitung

ADJ

ADJ H20 IR Bedienungsanleitung

ADJ

ADJ Vision Series Bedienungsanleitung

ADJ

ADJ MDF2-9SYS Bedienungsanleitung

ADJ

ADJ FS3000LED Bedienungsanleitung

ADJ

ADJ DOTZ PAR 100 Bedienungsanleitung

ADJ

ADJ Startec STINGER Bedienungsanleitung

ADJ

ADJ LINK Bedienungsanleitung

ADJ

ADJ COB CannOn Wash DW Bedienungsanleitung

ADJ

ADJ VIZ870 Bedienungsanleitung

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ 15 HEX BAR IP Bedienungsanleitung

ADJ

ADJ Focus Spot Three Z Bedienungsanleitung

ADJ

ADJ SABER BAR 6 Bedienungsanleitung

ADJ

ADJ Vizi Q Wash7 Bedienungsanleitung

ADJ

ADJ Mega GO Par64 PLUS Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung