ADJ MOD QW100 Bedienungsanleitung

User Instructions

MOD QW100

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation.

This device uses and can radiate radio frequency energy and, if not installed and used in accordance with

the included instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

Date Document

Version

Software

Version

DMX

Channel

Mode

Notes

01/19/18 1 1.00 4/5/6/9/10 Initial Release

03/20/19 1.2 1.01 No Change IR Remote Functions Updated

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 2

MOD QW100 Table of Contents

Introduction

Features / Warranty Registration / Installation

Safety Precautions

Control Panel Layout

DMX Set Up

DMX Addressing

DMX Channel Modes

System Menu

Operating Instructions

Master-Slave Conguration

UC IR/Airstream IR Control

Dimmer Curve Chart

Dimensional Drawings

Housing Change / Frost Filter

Power Linking / Trouble Shooting / Cleaning

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 3

MOD QW100 Introduction

Unpacking: Thank you for purchasing the MOD QW100 by ADJ Products, LLC. Every MOD QW100

has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the carton appears to be dam-

aged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit has arrived intact. In the case damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The ADJ MOD QW100 is a DMX intelligent, high powered LED par fixture. This xture

can be used in a stand alone set up or connected in a Master/Slave set up. The MOD QW100 has

seven operating modes: Sound Active mode, Auto Run mode, Color Change mode, Color Fade mode,

RGBW Dimmer mode, Static Color mode, and DMX controlled. To optimize the performance of this

product, please read these operating instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information regarding the use and maintenance

of this unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

MOD QW100 Features

• Multi-Colors

• Seven Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• Locking 3-Pin & 5-Pin XLR Connections In/Out

• Five DMX Modes: 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, 9 Channel Mode, and

10 Channel Mode.

• ADJ UC IR compatible and Airstream IR compatible

• Multiple Unit Power Linking (See page 29)

INCLUED:

1 x Scissor Yoke

1 x Locking Power Cable

3 x Frost Filters (20/40/60 Degrees)

OPTIONAL ACCESSORIES:

MOD Kit Pearl White Housing Case (Order Code: MOD510)

MOD QW100 Warranty Registration

MOD QW100 Installation

The MOD QW100 carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-

tacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

The unit should be mounted using a mounting clamp (not provided), axing it to the mounting

bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration

and slipping while operating. Always ensure that the structure to which you are attaching the unit is

secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable

that can hold 12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 4

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 5

MOD QW100 Safety Precautions

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 29

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a marked change in performance.

E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 6

MOD QW100 Control Panel Layout

SET UP

MODE UP

DOWN

DMX IN

DMX OUTDMX OUTPOWER OUT

DMX INPOWER IN

MODE BUTTON

SET UP BUTTON

UP BUTTON

DOWN BUTTON

LCD DISPLAY

POWER IN

POWER OUT

DMX IN

DMX OUT

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 7

MOD QW100 DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions

from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The MOD QW100

can be controlled via DMX-512 protocol. The MOD QW100 has 5 DMX channel

modes. The DMX address is set on the rear panel of the MOD QW100. Your unit and

your DMX controller require a standard 3-pin XLR connector for data input and data

output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your

own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may

be purchased at almost all pro lighting stores). Your cables should be made with a

male and female XLR connector on either end of the cable. Also remember that

DMX cable must be daisy chained and cannot be split. Figure 1

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the

female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

MOD QW100 DMX Set Up

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA transmis-

sion in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting

standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily

available at most electric stores. The chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 8

ADJ Products, LLC - www.adj.com - MOD QW100 User Manual Page 9

DMX ADDRESSING

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture

responds to the correct control signal. This digital starting address is the channel number from which

the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment

of this starting DMX address is achieved by setting the correct DMX address on the digital control

display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses

for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react

in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number

you have set, based on the quantity of DMX channels of each xture. That means changing the settings

of one channel will only aect the selected xture.

In the case of the MOD QW100, when in 10 Channel you should set the starting DMX address of the

rst unit to 1, the second unit to 11 (10 + 1), the third unit to 21 (11 + 10), and so on. (See chart below

for more details.)

MOD QW100 DMX Addressing

Channelmode Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

4 channels 1 5  9  13

5 channels 1 6  11 16

6 channels 1 7  13 19 

9 channels

10 channels

11 21

19 28

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ ENCORE PROFILE MINI COLOR Bedienungsanleitung

ADJ

ADJ MDF2-9SYS Bedienungsanleitung

ADJ

ADJ Encore Profile 1000 Color Bedienungsanleitung

ADJ

ADJ HYD320 Bedienungsanleitung

ADJ

ADJ PAR Z120 RGBW Bedienungsanleitung

ADJ

ADJ ADJ FLAT PAR TRI18X Bedienungsanleitung

ADJ

ADJ 1223200047 Leitfaden

ADJ

ADJ ikon profile ww Bedienungsanleitung

ADJ

ADJ Mega GO Par64 PLUS Bedienungsanleitung

ADJ

ADJ LTS COLOR Bedienungsanleitung

ADJ

ADJ ELEMENT H6 FC Bedienungsanleitung

ADJ

ADJ 7P HEX IP Bedienungsanleitung

ADJ

ADJ EVS3 Bedienungsanleitung

ADJ

ADJ M-103HD Bedienungsanleitung

ADJ

ADJ THEATRIX PRO 48 LED Bedienungsanleitung

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ VIZI BEAM 12RX Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ FOCUS BEAM LED Bedienungsanleitung

ADJ

ADJ 18P HEX IP Bedienungsanleitung

ADJ

ADJ M-1212 Bedienungsanleitung

ADJ

ADJ Royal 3D Bedienungsanleitung

ADJ

ADJ DOTZ PAR 100 Bedienungsanleitung

ADJ

ADJ MOD TW100 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung