ADJ REVO 4 IR Bedienungsanleitung

User Manual

REVO 4 IR

WARNING! Due to the magnifying type lens, please keep the lens

out of contact with direct sunlight. Direct sunlight can cause heat

to build up inside of the unit, which will result in serious damage.

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 2

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 3

Unpacking: Thank you for purchasing the Revo 4 IR by ADJ Products, LLC. Every Revo 4 IR has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all equipment necessary to operate the unit

has arrived intact. In the event damage has been found or parts are missing, please contact our toll-

free customer support number for further instructions. Please do not return this unit to your dealer

without contacting customer support rst.

Introduction: The Revo 4 IR can be a four or 256 channel, DMX intelligent LED xture. The xture has

three dierent operating modes; sound-active, show mode, DMX controlled. The Revo 4 IR has twelve

shows to choose from. The unit can be used as a stand-alone unit or in a primary/secondary congu-

ration. For best results use fog or special eects smoke to enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide help and

to answer any question should you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are

Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online, visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Warning! This may cause severe eye damage. Avoid looking directly into the light source at all times!

Revo 4 IR General Information

Revo 4 IR General Instructions

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit, for

future reference.

Revo 4 IR Warranty Registration

The Revo 4 IR carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card

to validate your purchase and warranty. You may also register your product online at www.adj.com.

All returned service items whether under warranty or not, must be freight pre-paid and accompany a

return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof

of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 4

Revo 4 IR Features

• DMX-512 Protocol Compatible (Four or 256 DMX Channels)

• RGB + White

• 3 Operating Modes - Show Mode; Sound Active; DMX Controlled

• Stand Alone or Primary/Secondary Configuration

• Internal Microphone

• Digital Display for Address and Function Setting

• UC IR Compatible (Not Included)

• 12 Show Modes

Revo 4 IR Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-obser-

vance of this manual or any unauthorized modification to this unit.

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 5

Revo 4 IR Safety Precautions

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before

You Attempt To Install Or Operate This Unit!

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 17

for cleaning details.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a marked change in

performance.

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 6

Power Supply: The ADJ Revo 4 IR contains an automatic voltage switch, which will auto sense the

voltage when it is plugged into the power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and

controller manufactures as a form of communication between intelligent fixtures and controllers. A

DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as

serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals locat-

ed on all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to

be linked together and operate from a single controller, as long as all fixtures and the controller are

DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. Therefore, the first

fixture controlled by the controller could be the last fixture in the chain. When a fixture is assigned

a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no

matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements: The Revo 4 IR can be controlled via DMX-512 protocol.

The Revo 4 IR can be a four or 256 channel DMX unit. The DMX address is set electronically using

the controls on the rear panel of the unit. Your unit and your DMX controller require an approved

DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend Accu-

Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm

shielded cable (This cable may be purchased at almost all professional sound and lighting stores).

Your cables should be made with a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Revo 4 IR Set Up

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 7

Notice: Be sure to follow gures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield

could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-

minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Revo 4 IR Set Up

5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission

in place of 3-pin. 5-pin XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting

standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are

readily available at most electric stores. The chart below details a proper cable conversion.

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 8

Revo 4 IR System Menu

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 9

System Menu: When conrming your setting press ENTER and then hold MENU for at least

2-3 seconds, or you can wait 1 minute for automatic setup. To exit without making any adjust-

ments press the MENU button.

ADDR - DMX Address Setting.

1. Press the MENU button until “ADDR” is displayed, press ENTER.

2. The current DMX address will now be displayed and ashing. Press the UP or DOWN buttons to

nd your desired address. Press ENTER to set your desired DMX address.

NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and

hold the MENU button for at least 3 seconds.

CHND - This will let you switch between 4 Channel DMX mode and 256 Channel DMX mode.

1. Press the MENU button until “CHND” is displayed, press ENTER. Either “4CH” or “256C” will be

displayed.

2. Press the UP or DOWN buttons to choose your desired DMX mode and press ENTER to conm

and exit.

SCND - This will let you set unit as a primary or secondary in a primary/secondary congura-

tion.

1. Press the MENU button until “SCND” is displayed, press ENTER. “PRI”, “SEC 1” or “SEC 2” will

be displayed.

2. Press the UP or DOWN buttons until your desired setting is dis-played, press ENTER to conrm

and exit.

SHND: SH 0 - SH 12 - Show modes 0 - 12

Show Mode can run with or without sound active mode on.

With sound active mode on, the shows will tend to run faster.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between 0-12. Programs 1-12 are preset

shows, while “Sh 0” is random mode. Press the UP or DOWN buttons to nd your desired show

and press ENTER to conrm.

3. Press ENTER to conrm, and then press and hold the MENU button for at least 3 seconds.

SOUN - In this mode you can run the unit in sound active mode.

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN buttons to select one or the

other.

3. When you have made your selection, press the ENTER, and then press and hold the MENU

button for at least 3 seconds to conrm.

SENS - In this mode you can adjust the sound sensitivity.

1. Press the MENU button until “SENS” is displayed, press ENTER. A number between 0-100 will be

displayed.

2. Press the UP or DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive, and 100

being the most sensitive.

3. When you have found your desired setting press ENTER to conrm.

Revo 4 IR System Menu

ADJ Products, LLC - www.adj.com - Revo 4 IR User Manual Page 10

DNST - This mode can be used as a precaution mode, that

in case the DMX signal is lost, interrupted, or power is lost, the operating mode chosen in the

setup is the running mode the xture will go into when the DMX signal is lost. You can also set

this as the operating mode you would like the unit to return to when power is applied.

1. Press the MENU button until “DNST” is displayed, and either “PRSE”, “BLND”, or “LAST” will be

displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use the UP or DOWN buttons to choose

an operating mode you would like the unit to start up in when power is applied or the DMX signal

is lost.

• PRSE (Primary Secondary) - If the DMX signal is lost or power is applied, the unit will

automatically go into Primary Secondary mode and run a built-in show.

• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into

stand by mode.

• LAST - If the DMX signal is lost the xture will stay in the last DMX setting. If power is

applied and this mode is set, the unit will automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up.

LED - With this function the LED display will turn o after 2 minutes

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to

keep the LED display on at all times, or “OFF” to allow the LED display to turn o after 2 minutes.

Press any button to turn on the LED display again.

3. Press ENTER to conrm and exit.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Press the UP button to select “DSIP” to invert the display, or select “DISP” to keep the display in

the normal, upright orientation.

3. Press ENTER to conrm.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running time of the unit.

1. Press the MENU button until “FHRS” is displayed, press ENTER.

2. The display shows the running time of the unit. Press MENU to exit.

VER - Use this function to display the Software version of the unit.

1. Press the MENU button until “VER” is displayed, press ENTER.

2. The display will show the software version.

Revo 4 IR System Menu

Andere Handbücher für REVO 4 IR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ MDF2PSUX117 Benutzerhandbuch

ADJ

ADJ HEX206 Bedienungsanleitung

ADJ

ADJ MOD TWIOO Bedienungsanleitung

ADJ

ADJ InnoRollLED Bedienungsanleitung

ADJ

ADJ Fusion Tri FX Bar Bedienungsanleitung

ADJ

ADJ ELEMENT H6 PAK Bedienungsanleitung

ADJ

ADJ Dotz Par Bedienungsanleitung

ADJ

ADJ ENCORE LP18IP Bedienungsanleitung

ADJ

ADJ 18P HEX IP Bedienungsanleitung

ADJ

ADJ BubbleTron Xl Bedienungsanleitung

ADJ

ADJ American DJ FUSION FX BAR 1 Bedienungsanleitung

ADJ

ADJ MB DMX II Bedienungsanleitung

ADJ

ADJ Gobo Motion LED Montageanleitung

ADJ

ADJ VF FLURRY Bedienungsanleitung

ADJ

ADJ Par Z Move RGBW Bedienungsanleitung

ADJ

ADJ ECO UV BAR PLUS IR Bedienungsanleitung

ADJ

ADJ Inno Pocket Wash Bedienungsanleitung

ADJ

ADJ LTS COLOR Bedienungsanleitung

ADJ

ADJ IKON IR Bedienungsanleitung

ADJ

ADJ WiFly NE1 Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ WIFLY PAR QA5 Bedienungsanleitung

ADJ

ADJ penta pix Bedienungsanleitung

ADJ

ADJ MOD QA60 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung