ADT QuickConnect Gebrauchs- und Pflegehandbuch

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Compatible with:

Ademco Lynx

ADT QuickConnect

Instructions:

W H A T Y O U ’ L L N E E D :

•A registered MyADT Account

•1 small Phillips head screwdriver

•7.2V, 3700mAh battery

You can purchase a 7.2 Volt 3700 mAh battery from MyADT or from retailers such as Walmart,

Amazon, Batteries Plus, Home Depot, and Lowe’s. We also recommend checking with your local

retailers for availability. Here are the specifications of the 7.2 Volt 3700 mAh battery:

•Voltage: 7.2 V

•Capacity: 3700 mAh

•Terminals: Connector

•Chemistry: NiMH

•Length: 4”

Battery Instructions:

Ademco Lynx & ADT QuickConnect

•Width: 2.7”

•Height: 0.07”

•Weight: 0.30 lbs.

N O T E :

The battery pack is located inside the keypad. The battery pack has black and red wires coming out of

it with a modular connector at the end.

C A U T I O N :

Do not remove the green plastic cover from around the new battery pack. This covering is necessary

for a proper connection and may cause serious injury or damage if removed or damaged.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 1:

Set your system to Test Mode. Log into your MyADT account, click on the Alarm System tab, and select

System Test.

Step 2:

Unplug the control panel’s transformer from the outlet. You may need the screwdriver to remove the

retaining screw on the transformer.

Step 3:

Find the two tabs on top of your keypad, press them in to release the cover and gently pull the keypad

toward you.

Step 4:

Quickly inspect the old battery. If the battery looks abnormal (i.e. has a swollen or split case, liquid

leaking from the case, or corroded terminals) close the keypad and call (800) ADT-ASAP to schedule a

service call.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 5:

Remove the small screw from the plastic battery bracket. Be sure to put the screw in a place where you

won’t lose it since you’ll need it later.

Step 6:

Gently remove the wires from their retaining clips, and then disconnect the battery wires by pulling on

the plastic connector.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Then tip the top of the battery up to remove it from the compartment.

Step 7:

Remove the new battery from its packaging.

C A U T I O N :

Do not remove the green plastic cover from around the new battery pack. This covering is necessary

for a proper connection and may cause serious injury or damage if removed or damaged.

Step 8:

Place the new battery in the compartment and then screw in place the plastic battery bracket.

Step 9:

Thread the wires under the retaining clips, remove the protective plastic from the connector, and plug

it into the receptacle.

Step 10:

Replace the keypad, the two tabs snap back into place, and then plug the transformer back into the

outlet.

Battery Instructions:

Ademco Lynx & ADT QuickConnect

Step 11:

Check your alarm keypad to ensure it no longer displays the “BAT” or “SYSTEM LO BATTERY”

message. If it still shows a low battery message, try entering your code and pressing the OFF button.

Repeat if necessary. If the message still shows, it may take 24 to 48-hours for the battery to fully charge.

If after 48-hours the message still shows, please go to MyADT.com and start a Chat Session with us, or

call (800) ADT-ASAP to troubleshoot your system.

When the message is gone or you’re waiting for the battery to charge, remove your system from Test

Mode at MyADT.com.

Ensure your system is working properly by testing your system. Go to MyADT.com and place your

system on test and then follow the directions in the user guide to test your system or visit MyADT.com

to find your user guide

Inhaltsverzeichnis

Andere ADT Sicherheitssystem Handbücher

ADT

ADT Safewatch Pro 3000 Benutzerhandbuch

ADT

ADT TSSC Montageanleitung

ADT

ADT Garda Response PM30 Bedienungsanleitung

ADT

ADT Commercial Fire & Burglary Alarm System FOCUS 200... Montageanleitung

ADT

ADT ADTHYBWL Series Bedienungsanleitung

ADT

ADT On-The-Go Bedienungsanleitung

ADT

ADT iCenter 8142ADT Bedienungsanleitung

ADT

ADT Safewatch Quick Connect Plus Bedienungsanleitung

ADT

ADT Commercial Fire & Burglary Alarm System FOCUS 200... Bedienungsanleitung

ADT

ADT PremisePro none Bedienungsanleitung

ADT

ADT SAFEWATCH EZ Bedienungsanleitung

ADT

ADT Commercial Fire & Burglary Alarm System FOCUS 200... Bedienungsanleitung

ADT

ADT On-The-Go Emergency Response System Bedienungsanleitung

ADT

ADT SASW3000EN Bedienungsanleitung

ADT

ADT SECURITY MANAGER 2000 Bedienungsanleitung

ADT

ADT Safe-N-Go Bedienungsanleitung

ADT

ADT Security System D7412 Bedienungsanleitung

ADT

ADT BHS-3000C Bedienungsanleitung

ADT

ADT Keychain Remote Bedienungsanleitung

ADT

ADT Entrepreneur 3000EN Betriebsanleitung

ADT

ADT Safewatch Plus Enterpreneur Security Systems Bedienungsanleitung

ADT

ADT 3G Cellular Medical Alert System Bedienungsanleitung

ADT

ADT SAFEWATCH PRO Bedienungsanleitung

ADT

ADT Ademco Vista 20P/PSIA Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung