ADTRAN Cable T1 ESF CSU ACE Bedienungsanleitung

T1 ESF CSU ACE

User Manual

Part Number 1203025L1

61203025L1-1C

May 2001

Trademark Information:

T-WATCH is a trademark of ADTRAN.

OpenView is a registered trademark of Hewlett Packard Company.

SunNet Manager is a trademark of Sun Micro Systems, Inc.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

iii

The following conventions are used in this manual.

Important Safety Instructions

When using your telephone equipment, please follow these basic safety precautions

to reduce the risk of fire, electrical shock, or personal injury:

1. Do not use this product near water, such as near a bathtub, wash bowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm.

There is a remote risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual.

Do not dispose of batteries in a fire. They may explode. Check with local codes

for special disposal instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equip-

ment or endangerment to human life.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital

terminal equipment without encoded analog content and billing protection is

used to transmit digital signals containing encoded analog content which are

intended for eventual conversion into voice band analog signal and transmitted

on the network.

• The affidavit shall affirm that either no encoded analog content or billing informa-

tion is being transmitted or that the output of the device meets Part 68 encoded

analog content or billing protection specification.

• End use/customer will be responsible to file an affidavit with the local exchange

carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital ser-

vice.

• Until such time as subrate digital terminal equipment is registered for voice appli-

cations, the affidavit requirements for subrate services are waived.

Affidavit for Connection of Customer Premises Equipment to 1.544 MBPS and/

or Subrate Digital Services

For the work to be performed in the certified territory of ______________ (telco name)

State of ________________________________

County of ______________________________

I, _______________________ (name), ____________________ (business address),

_____________________ (telephone number) being duly sworn, state:

I have the responsibility for the operation and maintenance of the terminal equipment

to be connected to 1.544 Mbps and/or __________________ subrate digital services.

The terminal equipment to be connected complies with Part 68 of the FCC rules

except for the encoded analog content and billing protection specification.With

respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance and adjust-

ment of the digital CPE with respect to encoded analog content and billing protection

information continuously complies with Part 68 of the FCC rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog con-

tent or billing information which is intended to be decoded within the telecommuni-

cations network.

( ) The encoded analog content and billing protection is factory set and is not under

the control of the customer.

I attest that the operator(s) maintainer(s) of the digital CPE responsible for the estab-

lishment, maintenance and adjustment of the encoded analog content and billing

information has (have) been trained to perform these functions by successfully having

completed one of the following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used

to encode analog signals; or

( ) B. A training course provided by the customer or authorized representative, using

training materials and instructions provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) rec-

ognized by the manufacturer/grantee of the equipment used to encode analog sig-

nals; or

( ) D. In lieu of the proceeding training requirements, the operator(s)/maintainer(S) is

(are) under the control of a supervisor trained in accordance with _______________

(circle one) above.

I agree to provide ____________________ (telco’s name) with proper documentation

to demonstrate compliance with the information in the preceding paragraph, if so

requested.

_____________________ Signature

_____________________ Title

_____________________ Date

Subscribed and sworn to before me

This _________ day of ___________________, 20__

_______________________________________

Notary Public

My commission expires: _________________________

vii

FCC regulations require that the following information be provided in this man-

ual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of the

equipment housing is a label that shows the FCC registration number and Ringer

Equivalence Number (REN) for this equipment, if applicable. If required, this

information must be given to the telephone company.

2. The following information may be required when applying to the local telephone

company for leased line facilities.

3. An FCC compliant telephone cord with a modular plug may be provided with

this equipment. This equipment is designed to be connected to the telephone net-

work or premises wiring using a compatible modular jack, which is FCC Part 68

compliant. See installation instructions for details.

4. If this equipment causes harm to the telephone network, the telephone company

may temporarily discontinue service. If possible, advance notification is given;

otherwise, notification is given as soon as possible. The telephone company will

advise the customer of the right to file a complaint with the FCC.

5. The telephone company may make changes in its facilities, equipment, operations,

or procedures that could affect the proper operation of this equipment. If this hap-

pens, the telephone company will provide advance notification and the opportunity

to make the necessary modifications to maintain uninterrupted service.

6. If experiencing difficulty with this equipment, please contact ADTRAN for repair and

warranty information. If the equipment is causing harm to the network, the tele-

phone company may request this equipment to be disconnected from the network

until the problem is resolved or it is certain that the equipment is not malfunctioning.

7. This unit contains no user-serviceable parts.

8. The FCC recommends that the AC outlet to which equipment requiring AC

power is to be installed is provided with an AC surge arrester.

Service Type REN/SOC FIC USOC

1.544 Mbps - SF 6.0F 04DU9-BN RJ48C

1.544 Mbps - SF and B8ZS 6.0F 04DU9-DN RJ48C

1.544 Mbps - ESF 6.0F 04DU9-1KN RJ48C

1.544 Mbps - ESF and B8ZS 6.0F 04DU9-1SN RJ48C

viii

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction man-

ual, may cause harmful interference to radio frequencies. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC

limits.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus as set out in the interference-causing equipment standard enti-

tled “Digital Apparatus," ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:

"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

Change or modifications to this unit not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate the equip-

ment.

Canadian Equipment Limitations

Notice: The Canadian Industry and Science Canada label identifies certified equip-

ment. This certification means that the equipment meets certain telecommunications

network protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be con-

nected to the facilities of the local telecommunications company. The equipment must

also be installed using an acceptable methods of connection. In some cases, the com-

pany’s inside wiring associated with a single line individual service may be extended

by means of a certified connector assembly (telephone extension cord). The customer

should be aware that compliance with the above limitations may not prevent degra-

dation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian mainte-

nance facility designated by the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

TheLoadNumber(LN)assignedtoeachterminaldevicedenotesthepercentageof

the total load to be connected to a telephone loop which is used by the device, to pre-

vent overloading. The termination on a loop may consist of any combination of

devices subject only to the requirement that the total of the Load Numbers of all

devices does not exceed 100.

Users should not attempt to make such connections themselves, but

should contract the appropriate electric inspection authority, or an elec-

trician, as appropriate.

Limited Product Warranty

ADTRAN warrants that for five (5) years from the date of shipment to Customer, all

products manufactured by ADTRAN will be free from defects in materials and work-

manship. ADTRAN also warrants that products will conform to the applicable speci-

fications and drawings for such products, as contained in the Product Manual or in

ADTRAN's internal specifications and drawings for such products (which may or

may not be reflected in the Product Manual). This warranty only applies if Customer

gives ADTRAN written notice of defects during the warranty period. Upon such

notice, ADTRAN will, at its option, either repair or replace the defective item. If ADT-

RAN is unable, in a reasonable time, to repair or replace any equipment to a condition

as warranted, Customer is entitled to a full refund of the purchase price upon return

of the equipment to ADTRAN. This warranty applies only to the original purchaser

and is not transferable without ADTRAN's express written permission. This warranty

becomes null and void if Customer modifies or alters the equipment in any way, other

than as specifically authorized by ADTRAN.

EXCEPT FOR THE LIMITEDWARRANTY DESCRIBED ABOVE, THE FOREGOING

CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND

THE EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL

OTHER WARRANTIES (EXPRESSED OR IMPLIED). ADTRAN SPECIFICALLY DIS-

CLAIMS ALL OTHER WARRANTIES, INCLUDING (WITHOUT LIMITATION),

ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIEDWAR-

RANTIES, SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER.

In no event will ADTRAN or its suppliers be liable to Customer for any incidental,

special, punitive, exemplary or consequential damages experienced by either Cus-

tomer or a third party (including, but not limited to, loss of data or information, loss

of profits, or loss of use). ADTRAN is not liable for damages for any cause whatso-

ever (whether based in contract, tort, or otherwise) in excess of the amount paid for

the item. Some states do not allow the limitation or exclusion of liability for incidental

or consequential damages, so the above limitation or exclusion may not apply to Cus-

tomer.

Andere Handbücher für Cable T1 ESF CSU ACE

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN DSU IQ Bedienungsanleitung

ADTRAN

ADTRAN T200 IDSL OCU-R Bedienungsanleitung

ADTRAN

ADTRAN XFP NG-PON2 ONU Bedienungsanleitung

ADTRAN

ADTRAN 602 Bedienungsanleitung

ADTRAN

ADTRAN T200 H4R Bedienungsanleitung

ADTRAN

ADTRAN Total Access 374 Produkthandbuch

ADTRAN

ADTRAN Express 3100 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Bedienungsanleitung

ADTRAN

ADTRAN 4200990G1 Handbuch

ADTRAN

ADTRAN DS3 NIU3 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 8044M Bedienungsanleitung

ADTRAN

ADTRAN Total Access 480 Bedienungsanleitung

ADTRAN

ADTRAN ATLAS 800 Series Module QUAD E1 Bedienungsanleitung

ADTRAN

ADTRAN OC-12 Bedienungsanleitung

ADTRAN

ADTRAN OSU 300 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 6330 Series Bedienungsanleitung

ADTRAN

ADTRAN FXS/DPO/PLAR 1109403L2 Bedienungsanleitung

ADTRAN

ADTRAN 24-Port DSLAM Access Module IADSL Module Bedienungsanleitung

ADTRAN

ADTRAN MX410 Bedienungsanleitung

ADTRAN

ADTRAN NETVANTA OCTAL POE Bedienungsanleitung

ADTRAN

ADTRAN BR10 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 900 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 832 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung