ADTRAN ISU 512E Bedienungsanleitung

ISU 512e

ISDN Service Unit

Part Number 1203086L1

Document Number 61203086L1-1A

September 1999

Trademarks:

DMS-100 is a trademark of Northern Telecom, Inc.

5ESS is a registered trademark of LUCENT.

ISU is a trademark of ADTRAN, Inc.

ExpertISDN is a trademark of ADTRAN, Inc.

SunNet Manager is a registered trademark of Sun Microsystems, Inc.

HP Openview is a registered trademark of Hewlett-Packard Com-

pany.

Netview is a registered trademark of IBM.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

iii

ADTRAN YEAR 2000 (Y2K)

READINESS DISCLOSURE

ADTRAN has established a Year 2000 program to ensure that our

products and operations will correctly function in the new millen-

nium. ADTRAN warrants that all products meet Year 2000 specifica-

tions regardless of model or revision. Information about ADTRAN’s

Year 2000 compliance program is available at the following:

Web Site www.adtran.com

Product Matrix www.adtran.com/Y2Kfax.html

Faxback Document Line (256) 963-8200

Y2K plans and product certifications

are listed in the matrix

Y2K Project Line (256) 963-2200

E-mail year 2000@adtran.com

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of fire, electric shock and

injury to persons. The precautions are listed below.

1. Do not use this product near water (for example, near a bath tub,

wash bowl, kitchen sink or laundry tub, in a wet basement or near

a swimming pool).

2. Avoid using a telephone (other than a cordless type) during an

electrical storm. There may be a remote risk of electric shock from

lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the

leak.

4. Useonlythepower cord,powersupply, and/orbatteries indicated

in the manual. Do not dispose of batteries in a fire. They may ex-

plode. Check local codes for any special disposal instructions.

SAVE THESE INSTRUCTIONS.

FCC regulations require that the following information be pro-

vided in this manual:

1. This equipment complies with Part 68 of the FCC rules. On the bot-

tom of the equipment housing is a label that shows the FCC regis-

tration number and Ringer Equivalent Number (REN) for this

equipment. If requested, provide this information to the telephone

company.

2. If this equipment causes harm to the telephone network, the tele-

phone company may temporarily discontinue service. If possible,

advance notification is given; otherwise, notification is given as

soon as possible. The telephone company will advise the customer

of the right to file a complaint with the FCC.

3. The telephone company may make changes in its facilities, equip-

ment, operations, or procedures that could affect the proper oper-

ation of this equipment; advance notification and the opportunity

to maintain uninterrupted service are given.

4. If experiencing difficulty with this equipment,please contact ADT-

RAN (see inside back cover) for repair and warranty information.

The telephone company may require this equipment to be discon-

nected from the network until the problem is corrected or until it is

certain the equipment is not malfunctioning.

5. This unit contains no user serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provid-

ed with this equipment. In addition, an FCC compliant cable ap-

propriate for the dial backup option ordered is provided. This

equipmentis designed to be connectedtothe telephonenetwork or

premises wiring using an FCC compatible modular jack, which is

Part 68 compliant.

7. The following information may be required when applying to the

local telephone company for leased line facilities.

Service Type Digital Facility

Interface Code Service Order

Code Network

Jacks

ISDN 021S5 6.0F RJ-49C

FEDERAL COMMUNICATIONS COMMISSION RADIO

FREQUENCY INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio or

TV reception. The user is encouraged to try to correct the interference

by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Change or modifications to this unit not expressly ap-

proved by ADTRAN will void the user’s authority to

operate the equipment.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus as set out in the interference-

causingequipmentstandard entitled "DigitalApparatus," ICES-003of

the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques

applicables aux appareils numeriques de Class B prescrites dans la

norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003

edictee par le ministre des Communications.

vii

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies

certified equipment. This certification means that the equipment

meets certain telecommunications network protective, operational,

and safety requirements. The Department does not guarantee the

equipment will operate to the user’s satisfaction.

Before installing this equipment, ensure that it is permissible to be

connected to the facilities of the local telecommunications company.

The equipment must also be installed using an acceptable method of

connection. In some cases, the company’s inside wiring associated

with a single-line individual service may be extended by means of a

certified connector assembly (telephone extension cord). Compliance

with the above conditions may not prevent degradation of service in

some situations.

Repairs to certified equipment should be made by an authorized Ca-

nadian maintenance facility designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment mal-

functions, may give the telecommunications company cause to re-

quest the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines, and internal metallic

water pipe system, if present, are connected together. This precaution

may be particularly important in rural areas.

Users should not attempt to make such connections

themselves, but should contact the appropriate electric

inspection authority, or an electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the

percentage of the total load to be connected to a telephone loop which

is used by the device, to prevent overloading. The termination on a

loop may consist of any combination of devices subject only to the re-

quirement that the total of the Load Numbers of all devices does not

exceed 100.

viii

AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL

SERVICES

• An affidavit is required to be given to the telephone company

whenever digital terminal equipment without encoded analog

content and billing protection is used to transmit digital signals

containing encoded analog content which are intended for even-

tual conversion into voiceband analog signals and transmitted on

the network.

• The affidavit shall affirm that either no encoded analog content or

billing information is being transmitted or that the output of the

device meets Part 68 encoded analog content or billing protection

specifications.

• End user/customer will be responsible to file an affidavit with the

local exchange carrier when connecting unprotected CPE to a

1.544 Mbps or subrate digital service.

• Untilsuch time as subratedigital terminal equipmentis registered

for voice applications, the affidavit requirement for subrate ser-

vices is waived.

AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES

EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL

SERVICES

For the work to be performed in the certified territory of

_________________________

(telco name)

State of ___________________

County of __________________

I, _______________________________ (name),

_________________________________ (business address),

_________________________________ (telephone number)

being duly sworn, state:

I have responsibility for the operation and maintenance of the termi-

nal equipment to be connected to 1.544 Mbps and/or

_________subrate digital services. The terminal equipment to be con-

nected complies with Part 68 of the FCC rules except for the encoded

analog content and billing protection specifications. With respect to

encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, main-

tenance, and adjustment of the digital CPE with respect to encoded

analog content and billing protection information continuously com-

plies with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encod-

ed analog content or billing information which is intended to be de-

coded within the telecommunications network.

( ) The encoded analog content and billing protection isfactory set and

is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsi-

ble for establishment, maintenance, and adjustment of the encoded

analog content and billing information has (have) been trained to per-

form these functions by successfully having completed one of the fol-

lowing (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) B. A training course provided by the customer or authorized repre-

sentative, using training materials and instructions provided by the

manufacturer/grantee of the equipment used to encode analog sig-

nals; or

( ) C. An independent training course (e.g., trade school or technical

institution) recognized by the manufacturer/grantee of the equip-

ment used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/

maintainer(s) is (are) under the control of a supervisor trained in ac-

cordance with __________________ (circle one) above.

I agree to provide ______________________(telco’s name) with proper

documentation to demonstrate compliance with the information as

provided in the preceding paragraph, if so requested.

______________________________Signature

______________________________Title

______________________________Date

Transcribed and sworn to before me

This ____day of _________, 199 ____

______________________________

Notary Public

My commission expires:

______________________________

Andere Handbücher für ISU 512E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN NIU3 Bedienungsanleitung

ADTRAN

ADTRAN Total Access DSLAM 16-Port ADSL2+ Access Module... Bedienungsanleitung

ADTRAN

ADTRAN Total Access 480 Bedienungsanleitung

ADTRAN

ADTRAN T200 H2TU-R Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Produkthandbuch

ADTRAN

ADTRAN 1200221L1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 362R Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

ADTRAN

ADTRAN IQ 710 Benutzerhandbuch

ADTRAN

ADTRAN NetVanta 900 Series Handbuch

ADTRAN

ADTRAN 1442703PG2 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta E1/FE1 Network Interface Module Bedienungsanleitung

ADTRAN

ADTRAN T1 CSU ACE Bedienungsanleitung

ADTRAN

ADTRAN SFP Series Bedienungsanleitung

ADTRAN

ADTRAN Dial Backup Interface Module 1204006L2 Bedienungsanleitung

ADTRAN

ADTRAN Ethernet Over Bonded Copper MX3112 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 324E Bedienungsanleitung

ADTRAN

ADTRAN GPON 452 Bedienungsanleitung

ADTRAN

ADTRAN 1442351G7 Bedienungsanleitung

ADTRAN

ADTRAN NIU3 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 544R Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 1248 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung