ADTRAN Total Access 900 Series Bedienungsanleitung

Technical Support 1-888-4ADTRAN (1-888-423-8726)

Configuring the

Total Access 900 Series

Web-Based GUI, AOS CLI,

and Connecting to the Unit

Quick Configuration Guide 61210916L1-42.1B March 2006

Web-Based GUI

The Web-based GUI is an online configuration tool that allows you to easily configure and view

the main settings, as well as the status of your system.

1. Connect the Total Access 900 Series unit to your network using the ETH 0/1 port on the rear

panel of the unit. The Total Access 900 Series units support auto MDI-MDIX crossover;

therefore, a straight-through cable can be used for this connection.

2. Configure your PC to obtain an IP address automatically (DCHP), or change the IP address

of your PC to 10.10.10.2. The default address for the Total Access 900 Series unit is

10.10.10.1.

3. Enter the IP address 10.10.10.1 (default) in your Internet browser Address field (see

example, below).

The configuration parameters used in the example outlined in this document are for

instructional purposes only. Please replace all example entries with your specific parameters

to configure your application.

Using the Web-Based GUI

Contact your network administrator if you need assistance changing your computer’s

IP settings.

If you cannot change the PC’s IP address, you will need to change the Total Access

900 Series IP address. For this procedure, see Connecting to the Total Access

900 Series on page 4.

2 Technical Support 1-888-4ADTRAN (1-888-423-8726) 61210916L1-42.1B

4. Once you are connected, you will be prompted to enter the user name and password.

Enter your User name (default is admin) and Password (default is password) and click OK.

5. The initial GUI screen appears.

While navigating the Web GUI, you will notice question mark symbols that

indicate additional information is available. Simply place your cursor over the symbol

to view the additional information.

61210916L1-42.1B Technical Support 1-888-4ADTRAN (1-888-423-8726) 3

Once you have logged in, click on Config Wizard to display the screen below. Use the buttons at

the bottom of the screen or the menu at the top left to navigate the Config Wizard.

Use the system’s Config Wizard utility as an online configuration tool to set up basic (as well as

advanced) voice applications. The Config Wizard can easily walk you through system setup,

voice and data settings, and trunk and station configuration through a series of easy to answer

questions. At the end of the wizard, you can review your choices and accept them or make

additional changes.

Using the Configuration Wizard

ADTRAN recommends using this wizard only for new installations. Some existing settings

may be lost or reset when using this wizard.

4 Technical Support 1-888-4ADTRAN (1-888-423-8726) 61210916L1-42.1B

Follow these steps if you are not able to change the PC’s IP address in order to access the Web

GUI. Change the Total Access 900 IP address to correspond with your network setup. See the

steps below for further instruction.

Connecting to the CRAFT Port

1. Connect a VT100 terminal (or PC with VT100 emulation software) to the Total Access 900

Series CRAFT port on the rear panel of your unit using a DB-9 (male) to DB-9 (female)

straight-through serial cable.

2. Insert the connector of the provided power cord into the power interface on the side panel of

the unit, and plug the cord into a standard electrical outlet.

3. Open a VT100 terminal session and configure the terminal’s COM port with the following

parameters:

Data Rate: 9600

Data Bits: 8

Parity Bits: None

Stop Bits: 1

Flow Control: None

4. Press the <Enter> key to activate the Adtran Operating System Command Line Interface

(AOS CLI). The AOS CLI allows you to access and control the system through a command-

driven CRAFT connection.

5. Enter enable at the > prompt, and enter the password when prompted. The default password

is password.

Changing the Total Access 900 Series IP Address

1. Enter config terminal to enter the Global Configuration mode.

2. Enter interface ethernet 0/1 to access the Ethernet interface.

3. Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the Ethernet port

using a 24-bit subnet mask. Contact your Network Administrator to obtain the IP address

(and subnet mask) for your particular configuration.

4. Enter no shutdown to activate the interface to pass data.

5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration

mode.

Saving the Configuration

1. Enter exit to return to the Enable command security mode.

2. At the #prompt, enter copy running-config startup-config to save the current configuration

to memory.

3. Enter exit to close the configuration session.

Connecting to the Total Access 900 Series

Return to Using the Web-Based GUI on page 1 (step 3) to connect to the

Total Access 900 Series Web-based GUI.

Andere Handbücher für Total Access 900 Series

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN Dual Nx56/64 Bedienungsanleitung

ADTRAN

ADTRAN SFP Bedienungsanleitung

ADTRAN

ADTRAN ATLAS 800 Series Module QUAD E1 Bedienungsanleitung

ADTRAN

ADTRAN Express 3000 Bedienungsanleitung

ADTRAN

ADTRAN DS3 MX Bedienungsanleitung

ADTRAN

ADTRAN ATLAS 550 Bedienungsanleitung

ADTRAN

ADTRAN DDS-DP Produkthandbuch

ADTRAN

ADTRAN HTU-C Bedienungsanleitung

ADTRAN

ADTRAN jobAid NETVANTA Bedienungsanleitung

ADTRAN

ADTRAN TR OCU DP Bedienungsanleitung

ADTRAN

ADTRAN D4 TRI-C DP Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 8044M Bedienungsanleitung

ADTRAN

ADTRAN Ethernet Over Bonded Copper MX3112 Bedienungsanleitung

ADTRAN

ADTRAN MX410 Bedienungsanleitung

ADTRAN

ADTRAN Fractional T1 Tandem Channel Unit FT1-TDM Bedienungsanleitung

ADTRAN

ADTRAN 602 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta Series Bedienungsanleitung

ADTRAN

ADTRAN ISU 512E Bedienungsanleitung

ADTRAN

ADTRAN 1442940G1 Bedienungsanleitung

ADTRAN

ADTRAN 1442703PG2 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 324E Bedienungsanleitung

ADTRAN

ADTRAN 424 ONT Bedienungsanleitung

ADTRAN

ADTRAN DSU III TDM Bedienungsanleitung

ADTRAN

ADTRAN Network Interface Module T1/FT1 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung