ADTRAN SMART/RG SR555ac Bedienungsanleitung

SR555ac

Quick Start Guide

Installation

Locate the splitter cable that is included with your SmartRG gateway. It has three ports.

1. Connect the splitter as follows:

a. Connect the DSL port of the gateway and the Modem port of the splitter with a telephone cable

b. Connect the phone to the Phone port of the splitter with a telephone cable

c. Connect the incoming line to the Line port of the splitter.

2. Connect a LAN port of the gateway to the network card of the PC using an Ethernet cable.

3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gate-

way. Turn on the unit by pressing the On/Off button on the side of the gateway.

Note: If you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet

uplink, connect to the WAN interface using an Ethernet cable. You cannot use the xDSL uplink, 3G WAN service, and Eth-

ernet uplink at the same time.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to com-

plete before you can begin using your Internet applications (browser, email, etc.). If you are unable to connect to the Inter-

net, confirm that all cable connections are in place and the gateway’s power is turned on.

WAN

Modem

Line

RJ11

Phone

DSL USB

RESET

DC/

LAN

3G USB Data

Card / LTE

RJ45

LED Indicators

The indicator lights (LEDs) on the front of the SR555ac gateway

can help you understand the state of your gateway.

Legend: Green Green Blinking Red Lt. Blue Lt. Blue Blinking Dk Blue Dk. Blue Blinking

LED Action Explanation

All LEDs

except

those listed below Feature enabled &/or working correctly

Data being transferred

POWER Device in CFE mode

Device powered on and ready for use

DSL For VDSL only /WAN service

(Single Line -

Inner or Outer Pair)

For VDSL only WAN service (Bonded Line)

DSL line

acquiring sync

DSL line

(inner pair) connected DSL Line 0 (Inner pair) is active; DSL line 1 (Outer pair) is not

active.

DSL line

(outer pair) acquiring sync and con-

nected

DSL Line 1 (Outer pair) is active; DSL line 0 (Inner pair) is not

active

DSL connected Both DSL lines connected

LED Action Explanation

DSL down By default, this LED will blink when the DSL connection goes

down. You can modify this setting on the Advanced Settings >

DSL page.

Not lit No lines connected

Note: This LEDmay flash green briefly on startup.

INTERNET DSL sync acquired and gateway on line

Data being transferred

Internet authentication / connection has failed

Quick Gateway Configuration

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small cir-

cular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the

hole, press gently for 1 second, and then release the button. The system reboots and returns to the factory defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in the gateway's interface. Make sure that you have completed the

steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the factory default credentials shown below and click OK. The Device Info summary page appears.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Services sec-

tions of the SmartRG SR555ac Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the

instructions for the applicable method.

1. In the left navigation bar, click Wireless. The Basic page appears.

2. If the Enable Wireles checkbox is not already selected, click it to enable wireless.

3. If desired, in the SSID field, enter the network name to which you want your client devices connected. Continue

with the steps for the method you prefer.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow

these steps.

1. In the left navigation bar, click Wireless. Then click Security for the wireless band that you want to configure.

2. Select Enable WPS and click Apply/Save to commit your selection.

3. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a push-

button on its exterior or a software interface is used to initiate WPS connection. To learn how to use the WPS feature

on your client device, refer to its documentation.

Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS setup

such as connection failure, refer to your client device for further instructions.

Andere Handbücher für SMART/RG SR555ac

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Router Handbücher

ADTRAN

ADTRAN NetVanta 340 Series Handbuch

ADTRAN

ADTRAN 1200422L1 Handbuch

ADTRAN

ADTRAN NetVanta 3100 Series Bedienungsanleitung

ADTRAN

ADTRAN Express L768 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 340 Bedienungsanleitung

ADTRAN

ADTRAN TSU NetVanta Bedienungsanleitung

ADTRAN

ADTRAN Total Access 5000 Kurzanleitung

ADTRAN

ADTRAN TOTAL ACCESS 600R Benutzerhandbuch

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN BLUESOCKET VWLAN Bedienungsanleitung

ADTRAN

ADTRAN NETVANTA 3100 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1535P Handbuch

ADTRAN

ADTRAN NetVanta 3200 series Benutzerhandbuch

ADTRAN

ADTRAN Express L1.5 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN Express 4200 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5305 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4430 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3430 Bedienungsanleitung

ADTRAN

ADTRAN 4200990G1 Bedienungsanleitung

ADTRAN

ADTRAN Express 4100 Bedienungsanleitung

ADTRAN

ADTRAN Express XL Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3200 series Bedienungsanleitung

ADTRAN

ADTRAN NETVANTA 3200G Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise