Advantech PCL-725 Bedienungsanleitung
PCL-725
Relay Actuator and Isolated D/I Card
USER'S MANUAL
COPYRIGHT NOTICE
This documentation is copyrighted 1989 by Advantech Co.,
Ltd. All rights are reserved. Advantech Co., Ltd. Reserves
the right to make improvements in the products described
in this manual at any time without notice.
No part of this manual may be reproduced, copied,
translated or transmitted in any form or by any means
without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be
accurate and reliable. However, Advantech Co., Ltd.
assumes no responsibility for its use, nor for any
infringements of the rights of third parties which may result
from its use.
ACKNOWLEDGEMENTS
PC-LabCard is a trademark of Advantech Co., Ltd.
IBM and PC are trademarks of International Business
Machines Corporation.
MS-DOS is a trademark of Microsoft Corporation.
BASIC is a trademark of Dartmouth College.
Inter is a trademark of Intel Corporation.
Part No. 2003072500 4th Edition
Printed in Taiwan Sept. 1995
TABLE OF CONTENTS
CHAPTER 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1. General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2. Features, Application and Specifications . . . . . . . . . . . . . . . . . . . 2
CHAPTER2. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1. Initial Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2. Base Address Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.3. ConnectorPin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.4. Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5. Installing The PCL-725 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
CHAPTER3. DIGITAL I/O PROGRAMMING . . . . . . . . . . . . . . . . . . 11
CHAPTER 4. CUSTOMIZE THE CURRENT LIMIT RESISTOR . . .13
CHAPTER5. RELAY OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1. Using the ContactProtection Nomograph . . . . . . . . . . . . . . . . ..16
AppendixA. I/Oport Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CHAPTER 1. INTRODUCTION
1.1. General Description
The most common method of interfacing a microcomputer system, such as the
PC, is through the use of programmable digital input and output registers.
With digital output registers, the computer can write data into the registers,
treating the register as an I/O port. The output of these registers can then be
wired to an interface device, such as a relay. Thus, by writing data to an output
register, it would be possible to activate and deactivate a relay. The relay could,
in turn, control, for example, the power to a motor.
Digital input registers are similar but are used to sample the status of signals
attached to their inputs. For example, if a program wants to determine if a
switch is open or closed, the switch can be tied to the input of a digital input
register. A digital input register can be thought of as an I/O port that has wires
attached to individual bit locations. When read, the data results reflect the state
of the signals on the wires.
Designed with this idea in mind, the PCL-725 Relay Actuator & Isolated D/I
card is an IBM PC add-on card that offers you 8 relay actuators and 8 opto-
isolated digital inputs on a single board.
Typically, the 8 on-board relays can serve as ON/OFF control devices or small
power switches. The 8 opto-isolated D/I channels are ideal devices for
collecting digital inputs under noisy environment or floating potential. Also, the
8 isolated inputs provide the best method to prevent the ground loop problem.
For easy monitoring, each relay is equipped with one red LED to reflect its
ON/OFF status. Each input channel is jumper selectable to either isolated or
non-isolated input. Access to input and output channels is made possible
through a on-board 37-pin D type connector.
PCL-725 Introduction
1.2. Features, Application and Specifications
Features :
* 8 Relay actuator outputs.
* 8 Opto-isolated digital inputs.
* LED indicators to show activated relays.
* Jumper selectable isolated/non-isolated input signals.
* On-board relay driver circuits.
* On-board input signal conditioning circuits.
* Easy touse andprogram
Applications :
* Digital signal sensing.
* Switch contact status sensing.
* Limit switch monitoring.
* BCD interface.
* Industrial on/off control.
* Signal switching.
* Valve/solenoid control.
* External high power relay driving.
* Alarm activating.
* Annunciator control.
* Industrial automation.
* Laboratory automation.
* Useful with A/D's and D/A's.
PCL-725 Introduction
Specifications:
* Isolated Digital Input
Opto-isolator: 4N25
Input channels: 8
Input current: 60 MA max for isolated input. Input
buffered by voltage comparator
Input voltage: 5-24VDC
Input impedance: 560 Ohm/W
Threshold voltage: 1.5 VDC, adjustable by changing voltage
dividing resistors
Input mode: isolated or non-isolated
Withstanding voltage: 1500 VDC
* Non-isolated Digital Input
Logic level 0: 0-0.8 V
Logic level I: 2.0-5.25 V
" Relay Output
Relay Type: 4 SPDT (Form C)
4 SPST (Form A)
Contact rating: 120 V AC/DC, IA
Breakdown voltage: 1000 V AC/DC minimum
Operating time: 8 msec maximum (including Bounce)
Release time: 8 msec maximum
Insulation resistance: 100 MOhm minimum
Life expectancy: >10 million operations at full load
Power consumption: +12V, 33 mA for each relay, total
0.264A if ail relays are energized
+5V, less than 0.2A
Power supply: +12V from the PC bus
PCL-725 Introduction
* General
Dimensions : 5 3/4" x 3 3/4" (14.7 cm x 9.5 cm.)
Bus : IBM PC bus.
Slot : One 62-pin slot.
I/O port Address : Hex 200 - hex 3F8.
CHAPTER 2. INSTALLATION
2.1. Initial Inspection
Inside the shipping container, you should find this operating manual and the
PCL-725 card.
The PCL-725 was carefully inspected both mechanically and electrically before
shipment. It should be free of marks and scratches and in perfect electrical order
on receipt.
Remove the PCL-725 interface card from its protective packaging by grasping
the metal rear panel. Keep the anti-vibration package since it may be used to
return the card if it needs repair. The package may also be used if the card is
stored outside of the computer.
The board should be handled only by the edges. The integrated circuits on the
board can be damaged by static electric discharge.
2.2. Base Address Selection
Most of the peripheral devices and the interface adapters in the PC are
controlled and sensed using the digital input and output ports. These ports are
addressed using the I/O port address space of the 8088 or 80286 microcomputer.
The I/O port base address for the PCL-725 is selectable by an 8 position DIP
switch. Valid addresses are from hex 200 to hex 3FE. Refer to Figure 2.1 for the
location of the DIP switch (SW1).
PCL- 725 Installation
Figure 2.1 The PCL-725 Card
The required switch settings for various base addresses are illustrated as below :
Note : -ON = 0. OFF = 1
-"X" means "don't care"
-1..8 are switch positions
-A1..A8 correspond to address lines of the PC bus. A9 is
hard-wired to be 1.
-* means factory setting
PCL-725 Installation
-------------------------------------------------
I/O port switch position
address 1 2 3 4 5 6 7 8
(Hex) A8 A7 A6 A5 A4 A3 A2 Al
-------------------------------------------------
200-201 0 0 0 0 0 0 0 0
.
.
*2A8-2A9 0 1 0 1 0 1 0 0
.
.
2E8-2E9 0 1 1 1 0 1 0 0
2F8-2F9 0 1 1 1 1 1 0 0
3E8-3E9 1 1 1 1 0 1 0 0
3FE-3FF 1 1 1 1 1 1 1 1
2.3. Connector Pin Assignments
The PCL-725 card is equipped with a 37 pin D type connector accessible from
the rear plate. Please refer to Figure 2.1 for the location of the connector.
The following diagram below shows its pin assignments.
Legend:
DInL - digital input low, channeln
DInH - digital input high, channel n
GND -ground
NC n - normal close pin of relay n
NO n - normal open pin of relay n
COM n - common pin of relay n
PCL-725 Installation
NO 0 .1 20 . NO 3
COM 0 .2 21 . COM 3
NC 0 .3 22 . NC 3
NO 1 .4 23 . NO 4
COM 1 .5 24 . COM 4
NC 1 .6 25 . NO 5
NO 2 .7 26 . COM 6
COM 2 .8 27 . NO 6
NC 2 .9 28 . COM 6
NO 7 .10 29 . GND
COM 7 .11 30 . DI0L
DIOH .12 31 . DI1L
DI1H .13 32 . DI2L
DIZH .14 33 . DI3L
DI3H .15 34 . DI4L
DI4H .16 35 . DI5L
DI5H .17 36 . DI6L
DI6H .18 37 . DI7L
DI7H .19
2.4. Jumpers
There are two jumpers associated with each digital input channel for
configuring the channel as either isolated or non-isolated.
The following show the D/I channels and their corresponding jumpers :
D/I channel Jumpers
0JA0, JB0
1JA1, JB1
2JA2, JB2
3JA3, JB3
4JA4, JB4
5JA5, JB5
6JA6, JB6
7JA7, JB7
Examples are given here to illustrate how to configure the D/I channel. D/I
channel 1 is configured as isolated first, then non-isolated.
Inhaltsverzeichnis
Andere Advantech Computerhardware Handbücher
Advantech
Advantech ASMB-610V3 Installations- und Betriebshandbuch
Advantech
Advantech AIMC-3422 Installations- und Betriebshandbuch
Advantech
Advantech ECU-P1528PE Installations- und Betriebshandbuch
Advantech
Advantech AIMB-217 Bedienungsanleitung
Advantech
Advantech AIMC-3421 Installations- und Betriebshandbuch
Advantech
Advantech MIC-7420 Installations- und Betriebshandbuch
Advantech
Advantech PCA-6742 Series Installations- und Betriebshandbuch
Advantech
Advantech PCL-818L Bedienungsanleitung
Advantech
Advantech AMAX-4870 Installations- und Betriebshandbuch
Advantech
Advantech MIC-6311 Bedienungsanleitung
Advantech
Advantech PCE-5124 Bedienungsanleitung
Advantech
Advantech POC-W243 Series Bedienungsanleitung
Advantech
Advantech ARK-10 Bedienungsanleitung
Advantech
Advantech MOS-1121Y Series Bedienungsanleitung
Advantech
Advantech MIO-2363 Bedienungsanleitung
Advantech
Advantech MIO-5375 Installations- und Betriebshandbuch
Advantech
Advantech PCA-6742 Series Bedienungsanleitung
Advantech
Advantech PCA-6011 Installations- und Betriebshandbuch
Advantech
Advantech ASMB-831 Series Installations- und Betriebshandbuch
Advantech
Advantech TREK-550-A00E Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
