Advantech WISE-4210 Series Installations- und Betriebshandbuch

WISE-4210 Startup Manual 1

Thank you for purchasing the WISE-4210 module. This

quick start guide is intended to help you deploy your new

module. The guide contains basic information on the power

and application wiring.

Should you require additional instructions, please refer to

the user manual.

The WISE-4210 is designed for a standard industrial

unregulated 24 VDC power supply. For some applications,

it can also accept +10 to +50 VDC power input with 200 mV

peak-to-peak power ripple. The immediate ripple voltage

should be between +10 and +50 VDC. Batteries may also be

used as an alternative power source.

• 1 x WISE-4210 module

• 1 x Mounting bracket

• 1 x Quick start manual

• 1 x China RoHS declaration (UA series only)

• 1 x Antenna (UA series only)*

*For NA series, antennas should be ordered respectively

per required frequency range

** WISE-S200 I/O module should be ordered respectively

WISE-4210

Industrial LPWAN SUB-G Wireless I/O Module

Startup Manual

Open the rubber cover on the side of WISE-4210 nodes,

there is a battery switch to turn on or turn off the battery

power supply.

The module accepts 3 x AA, 3.6 V lithium battery. The bat-

teries should be installed facing the same direction.

Battery

Overview

For more information on this and other Advantech

products, please visit our website at:

http://www.advantech.com

For technical support and service:

https://www.advantech.com/support/

This startup manual is for WISE-4210.

Part No. 2003421052

Printed in Taiwan

Edition 3

October 2019

Input Power Requirements

Packaging List

Power Supply Wiring

2 WISE-4210 Startup Manual

WISE-S214 (4AI/4DI)

Digital Input- Dry Contact

Analog Input

WISE-S250 (6DI/2DO/1RS-485)

Digital Input-Dry Contact

Digital Output

RS-485 Port

WISE-S251 (6DI/1RS-485)

Digital Input – Dry Contact

RS-485 Port

Normal

Mode

Mode Light Press

(0.5 Sec)

Long Press

(2 Secs)

Power Sav-

ing Mode

LED turns

on→Gets

battery

level→LED

turns off*

Leave normal

mode

Non-power

Saving Mode

Getbattery

level→LED

turns off*

Leave normal

mode

Site-

Survey

Mode

Light Press

(0.5 Sec)

Long Press

(2 Secs)

Tx site survey packet Leave site survey mode

OTA

Mode

Status Light Press

(0.5 Sec)

Long Press

(2 Secs)

Rx Status Read battery

level

Leave OTA

mode

Tx Status

(by USB port)

Conguration Tx Firmware

Low Battery NA Leave OTA

mode

Update FW

fail

Reset OTA

mode NA

*LED indicators will go off automatically 15 secs later when

using battery power

Application Wiring

Membrane Button

WISE-4210 Startup Manual 3

Notes

1. Please install the CP210x USB to UART Controller driver: https://www.silabs.com/products/development-tools/software/

usb-to-uart-bridge-vcp-drivers.

2. ThepowerfromUSBisnotsufcienttopowerWISE-4210module.PleasepluginaDCpowersourcefrom+Vsand-Vs

pin.

Quick Start

1. Plug in a DC power source to the +Vs and -Vs pins of your module or insert charged batteries

2. Connect the module to your computer via the micro-USB port

3. Open WISE Studio and press Go To Conguration

4. Click ConnecttolinkWISE-4210-thewebcongurationpagewillappear

5. UsethewebcongurationinWISEUtilityorpressOpen In Browser toopenthewebcongurationpageinanybrowser

(GoogleChromeisrecommended)

6. Click Informationtocheckthestatusofthemoduleortocongurethemodule

4 WISE-4210 Startup Manual

LED Indicators

LED Color Indication Behavior

Status Green

Blink

2 Hz: Initial Status

0.5 Hz: Node is connected and normally at work

(Automatically goes OFF after 15 seconds when battery power is used)

On Site Survey mode

OFF OTA mode (RF RX or RF TX on)

RF RX Green

On(at least 10 ms) ReceivingdatafromtheGateway

On Listen RF channel

Off Idle

RF TX Yellow On(at least 10 ms) SendingdatatotheGateway

(Automatically disabled after 15 seconds when battery power is used)

Off Idle

Error Red

Fast Blink

• I/O Error

• OTA Fail

• TX/RX Firmware fail in OTA

Slow Blink • Low battery voltage

• Low RTC battery voltage

Off No error

Signal 4 Green Fast Blink • RF related error

Signal 3 Green Fast Blink • I/O error

Signal

Strength Green

On * 4

• Full signal

(In site survey mode)

• Battery level (100%)

(Automatically goes OFF after 15 seconds when battery power is used)

On * 3

• Goodsignal

(In site survey mode)

• Battery level (100~50%)

(same as above)

On * 2

• Okay signal

• Battery level (50~30%)

(same as above)

On * 1

• Poor signal

• Battery level (30~0%)

(same as above)

All Off • No signal

• Battery level (0%)

Battery Level

Battery PN: 1760002647-01

Indication

(Green) Percentage

4 100%

3 100~50%

2 50~30%

1 30~0%

Andere Handbücher für WISE-4210 Series

Andere Advantech E/A-System Handbücher

Advantech

Advantech ADAM-6050W Bedienungsanleitung

Advantech

Advantech AMAX-5000 Series Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Advantech

Advantech WISE-2200-M Installations- und Betriebshandbuch

Advantech

Advantech 48/24-Channel Digital Input/Output USB Module... Bedienungsanleitung

Advantech

Advantech PCL-813 Bedienungsanleitung

Advantech

Advantech ADAM-3600-A1F Bedienungsanleitung

Advantech

Advantech PCM-3753I-AE Bedienungsanleitung

Advantech

Advantech WISE-4610 Series Bedienungsanleitung

Advantech

Advantech ADAM-5000/TCP Series Bedienungsanleitung

Advantech

Advantech WISE-5000 Series Bedienungsanleitung

Advantech

Advantech ADAM-6156PN Bedienungsanleitung

Advantech

Advantech ADAM-6100PN Series Bedienungsanleitung

Advantech

Advantech PCI-1758UDO Installations- und Betriebshandbuch

Advantech

Advantech AMAX-5000 Series Bedienungsanleitung

Advantech

Advantech WISE-4000 Series Bedienungsanleitung

Advantech

Advantech WISE-4060 Installations- und Betriebshandbuch

Advantech

Advantech PCI-1713 Bedienungsanleitung

Advantech

Advantech WISE-4610 Series Bedienungsanleitung

Advantech

Advantech B+B SmartWorx Zlinx ZZ24D-NA-SR Bedienungsanleitung

Advantech

Advantech USB-4751 Bedienungsanleitung

Advantech

Advantech ADAM-6300 Series Bedienungsanleitung

Advantech

Advantech UNO-2000-LKAE Bedienungsanleitung

Advantech

Advantech USB-4716 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung